oSIST prEN 14188-4:2006

Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants

This European Standard specifies requirements for material characterisation for primers for hot and cold applied joint sealants for use in roads, airfields and other concrete pavements. This European Standard also applies for primers for hot applied joint sealants in bituminous surfacing and between bituminous surfacing and concrete pavements.

Fugeneinlagen und Fugenmassen - Teil 4: Spezifikationen für Voranstriche für Fugeneinlagen und Fugenmassen

Produits de scellement de joints - Partie 4 : Spécifications relatives aux primaires utilisés avec les produits de scellement de joints

Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants

General Information

• Status: Not Published
• ICS: 91.100.50 - Binders. Sealing materials
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CES - Roads
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 21-Mar-2014
• Due Date: 26-Mar-2014
• Completion Date: 21-Mar-2014
• Ref Project: prEN 14188-4 - Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 14188-4:2006
01-april-2006
Joint fillers and sealants - Part 4: Specifications for primers to be used with joint
sealants
Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants
Fugeneinlagen und Fugenmassen - Teil 4: Spezifikationen für Voranstriche für
Fugeneinlagen und Fugenmassen
Produits de scellement de joints - Partie 4 : Spécifications relatives aux primaires utilisés
avec les produits de scellement de joints
Ta slovenski standard je istoveten z: prEN 14188-4
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
oSIST prEN 14188-4:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 14188-4:2006

---------------------- Page: 2 ----------------------
oSIST prEN 14188-4:2006
EUROPEAN STANDARD
DRAFT
prEN 14188-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2006
ICS

English Version
Joint fillers and sealants - Part 4: Specifications for primers to be
used with joint sealants
Produits de scellement de joints - Partie 4 : Spécifications Fugeneinlagen und Fugenmassen - Teil 4: Spezifikationen
relatives aux primaires utilisés avec les produits de für Voranstriche für Fugeneinlagen und Fugenmassen
scellement de joints
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 227.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14188-4:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 14188-4:2006
prEN 14188-4:2006 (E)
Contents Page
Foreword.3
1 Scope.3
2 Normative references.3
3 Terms and definitions .4
4 Types.4
5 Requirements.4
5.1 Shelf life.4
5.2 Homogeneity.4
5.3 Density.4
5.4 Viscosity.5
5.5 Resistance against alkali.5
5.6 Drying behaviour.5
5.7 Solid content.5
5.8 Flash point.5
5.9 Softening point of solids.5
5.10 Dangerous substances.5
6 Evaluation of conformity.6
6.1 General.6
6.2 Type testing.7
6.2.1 Initial Type Testing .7
6.2.2 Further type testing .7
6.3 Factory Production Control (FPC) .7
6.3.1 General.7
6.3.2 Frequency of testing .7
6.3.3 Equipment.7
6.3.4 Raw materials and components.7
6.3.5 Design process.8
6.3.6 Non-conforming products.8
7 Marking, labelling and packaging .8
7.1 General.8
7.2 Primer.8
7.3 Containers.8
Annex A (normative) Initial Type Testing and frequencies of testing for Factory Production
Control .9
Annex B (informative) Example of a product data sheet.10

2

---------------------- Page: 4 ----------------------
oSIST prEN 14188-4:2006
prEN 14188-4:2006 (E)
Foreword
This European Standard (prEN 14188-4:2006) has been prepared by Technical Committee CEN/TC 227
“Road materials”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
1 Scope
This European Standard specifies requirements for material characterisation for primers for hot and cold
applied joint sealants for use in roads, airfields and other concrete pavements. This European Standard also
applies to primers for hot applied joint sealants in bituminous surfacing and between bituminous surfacing and
concrete pavements.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 14188-1, Joint fillers and sealants — Part 1: Specifications for hot applied sealants.
EN 14188-2, Joint fillers and sealants — Part 2: Specifications for cold applied sealants.
EN 1427, Bitumen and bituminous binders - Determination of softening point - Ring and ball method
EN 26927, Building construction — Jointing products−Sealants — Vocabulary.
EN ISO 2431, Paints and varnishes — Determination of flow time by use of flow cups.
EN ISO 2719, Determination of flash point — Pensky-Martens closed cup method.
EN ISO 2811-2, Determination of density.
prEN 15466-1, Primers for cold and hot applied joint sealants — Part 1: Test method for the determination of
homogeneity.
prEN 15466-2, Primers for cold and hot applied joint sealants — Part 2: Test method for the determination of
resistance against alkali.
prEN 15466-3, Primers for cold and hot applied joint sealants — Part 3: Test method for the determination of
drying behaviour and solid content.
3

---------------------- Page: 5 ----------------------
oSIST prEN 14188-4:2006
prEN 14188-4:2006 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 14188-1, EN 14188-2 and EN 26927
and the following apply.
3.1
primer
surface coating applied to the faces of the joint before placing the sealant in order to ensure its adhesion
3.2
manufacturer's limiting value MLV
the manufacturer’s stated minimum or maximum value to be met during testing according to the requirements
of this European Standard
3.3
manufacturer's declared value MDV
value declared by the manufacturer accompanied by a declared tolerance
4 T
...