F23.70 - Radiological Hazards

SIGNIFICANCE AND USE
5.1 This test method is intended to provide a standardized test procedure of protective materials to ensure comparable results among manufacturers and users.  
5.2 This test method involves measurement of the attenuation of X-rays by protective clothing material at an accelerating potential (kVp) between 60 and 130 kVp. These energies are considered to be representative of those commonly used during medical diagnosis.  
5.3 The reporting of the attenuation at a specific X-ray energy is intended to allow the end user organization to assess the attenuating properties of the protective clothing material at that energy level.
SCOPE
1.1 This test method establishes procedures for measuring the attenuation of X-rays by protective materials at accelerating potentials from 60 to 130 kVp.  
1.2 This test method provides attenuation values of primary beam X-radiation.  
1.3 This test method applies to both leaded and non-leaded radiation protective clothing materials.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is designed to provide a standardized procedure to ensure comparable results between manufacturers, testing laboratories, and users.  
5.2 This test method attempts to realistically quantify the radiation protection provided by radiation protective garments under real-world conditions for workers primarily exposed to scattered radiation in medical fluoroscopy work.  
5.3 This test method is designed to simulate exposure conditions to radiation scattered from the body of the patient undergoing fluoroscopy through an angle of 90° from the primary X-ray beam.  
5.4 The test method is designed to include contributions of radiation dose to the wearer from secondary radiation emitted from the shielding material.
SCOPE
1.1 This test method establishes a procedure for measuring the relative reduction in the intensity of X-radiation provided by shielding garments to the human user under conditions simulating actual use.  
1.2 This test method provides a condition simulating X-rays generated between 60 and 130 kV that are scattered through an angle of 90° by a water equivalent material.  
1.3 This test method applies to both leaded and no-leaded radiation protective materials.  
1.4 This test method provides a method for inclusion of secondary radiations generated within the protective material into a more realistic evaluation of radiation protection.  
1.5 The values given in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended to provide a standardized test procedure of protective materials to ensure comparable results among manufacturers and users.  
5.2 This test method involves measurement of the attenuation of X-rays by protective clothing material at an accelerating potential (kVp) between 60 and 130 kVp. These energies are considered to be representative of those commonly used during medical diagnosis.  
5.3 The reporting of the attenuation at a specific X-ray energy is intended to allow the end user organization to assess the attenuating properties of the protective clothing material at that energy level.
SCOPE
1.1 This test method establishes procedures for measuring the attenuation of X-rays by protective materials at accelerating potentials from 60 to 130 kVp.  
1.2 This test method provides attenuation values of primary beam X-radiation.  
1.3 This test method applies to both leaded and non-leaded radiation protective clothing materials.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is designed to provide a standardized procedure to ensure comparable results between manufacturers, testing laboratories, and users.  
5.2 This test method attempts to realistically quantify the radiation protection provided by radiation protective garments under real world conditions for workers primarily exposed to scattered radiation in medical fluoroscopy work.  
5.3 This test method is designed to simulate exposure conditions to radiation scattered from the body of the patient undergoing fluoroscopy through an angle of 90° from the primary X-ray beam.  
5.4 The test method is designed to include contributions of radiation dose to the wearer from secondary radiation emitted from the shielding material.
SCOPE
1.1 This test method establishes a procedure for measuring the relative reduction in the intensity of X-radiation provided by shielding garments to the human user under conditions simulating actual use.  
1.2 This test method provides a condition simulating X-rays generated between 60 and 130 kV that are scattered through an angle of 90° by a water equivalent material.  
1.3 This test method applies to both leaded and no-leaded radiation protective materials.  
1.4 This test method provides a method for inclusion of secondary radiations generated within the protective material into a more realistic evaluation of radiation protection.  
1.5 The values given in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7.

SIGNIFICANCE AND USE
5.1 This test method is intended to provide a standardized test procedure of protective materials to ensure comparable results among manufacturers and users.  
5.2 This test method involves measurement of the attenuation of X-rays by protective clothing material at an accelerating potential (kVp) between 60 and 130 kVp. These energies are considered to be representative of those commonly used during medical diagnosis and treatment.  
5.3 The reporting of the attenuation at a specific X-ray energy is intended to allow the end user organization to assess the attenuating properties of the protective clothing material at that energy level.
SCOPE
1.1 This test method establishes procedures for measuring the attenuation of X-rays by protective materials at accelerating potentials from 60 to 130 kVp.  
1.2 This test method provides attenuation values of primary beam X-radiation.  
1.3 This test method applies to both leaded and non-leaded radiation protective clothing materials.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method is intended to provide a standardized test procedure of protective materials to ensure comparable results among manufacturers and users.
This test method involves measurement of the attenuation of X-rays by protective clothing material at an accelerating potential (kVp) between 60 and 130 kVp. These energies are considered to be representative of those commonly used during medical diagnosis and treatment.
The reporting of the attenuation at a specific X-ray energy is intended to allow the end user organization to assess the attenuating properties of the protective clothing material at that energy level.
SCOPE
1.1 This test method establishes procedures for measuring the attenuation of X-rays by protective materials at accelerating potentials from 60 to 130 kVp.
1.2 This test method provides attenuation values of primary beam X-radiation.
1.3 This test method applies to both leaded and non-leaded radiation protective clothing materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.