CEN/TC 129/WG 3 - Laminated glass

This document defines terms and describes component parts for laminated glass and laminated safety glass for use in building.

This document specifies dimensions, limit deviations and edge finishes of laminated glass and laminated safety glass for use in building.
This document is not applicable to panes having an area less than 0,05 m2.

This document specifies performance requirements for laminated glass as defined in ISO 12543-1.
NOTE       Any defects that are found in installed laminated safety glass are dealt with in ISO 12543-6.

This document specifies defects of finished sizes and test methods with regard to the appearance of laminated glass and laminated safety glass when looking through the glass.
All references to laminated glass in this document refer to both laminated glass and laminated safety glass.
NOTE      Special attention is paid to acceptability criteria in the vision area.
This document is applicable to finished sizes at the time of supply.

This document specifies performance requirements for laminated safety glass as defined in ISO 12543-1.
NOTE       Any defects that are found in installed laminated safety glass are dealt with in ISO 12543-6.

This document specifies test methods relating to resistance to high temperature, humidity and radiation for laminated glass and laminated safety glass for use in building.

This European Standard covers the evaluation of conformity and the factory production control of
-   EN ISO 12543-2: Laminated safety glass;
-   EN ISO 12543-3: Laminated glass;
inclusive laminated (safety) glass with fire resistant properties.
For glass products with electrical wiring or connections for e.g. alarm or heating purposes, this standard covers only wiring subject for electrical potential difference to earth  less than 50 V a.c. or less than 75 V d.c.

CMC - Editorial error, numbering of subclauses in A.3

This document specifies a test method for determining the mechanical viscoelastic properties of interlayer materials. The interlayers under examination are those used in the production of laminated glass or laminated safety glass. The shear characteristics of interlayers are needed to design laminated glass in accordance with EN 16612:2019 and prEN 19100 (all parts).
Parameters of the Prony series, widely used in numerical simulation, can be derived from the measurements in Annex C.

This document specifies the composition, tolerances and characteristics, i.e. mechanical, acoustic, optical and thermal properties, of folio interlayers for the manufacturing of laminated glass and laminated safety glass for use in buildings and construction works and it defines their general quality criteria.
This document does not apply to interlayers for laminated glass which are achieved by pouring the interlayer material in liquid state on or between the plies of glass or plastic glazing sheet material generally followed by drying or chemical or ultraviolet curing.

This European Standard covers the assessment and verification of constancy of performances and the factory production control of laminated glass and laminated safety glass for use in buildings.
NOTE   For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.

ISO 12543-6:2011 specifies defects of finished sizes and test methods with regard to the appearance of laminated glass when looking through the glass.
ISO 12543-6:2011 is applicable to finished sizes at the time of supply.

ISO 12543-1:2011 defines terms and describes component parts for laminated glass and laminated safety glass for use in building.

ISO 12543-3:2011 specifies performance requirements for laminated glass as defined in ISO 12543-1.

ISO 12543-4:2011 specifies test methods in respect of resistance to high temperature, humidity and radiation for laminated glass and laminated safety glass for use in building.

ISO 12543-5:2011 specifies dimensions, limit deviations and edge finishes of laminated glass and laminated safety glass for use in building.

ISO 12543-6:2011 specifies defects of finished sizes and test methods with regard to the appearance of laminated glass when looking through the glass.
ISO 12543-6:2011 is applicable to finished sizes at the time of supply.

ISO 12543-2:2011 specifies performance requirements for laminated safety glass as defined in ISO 12543-1.

ISO 12543-2:2004 specifies performance requirements for laminated safety glass.

This part of this European Standard specifies dimensions, limit deviations, and edge finishes of laminated glass and laminated safety glass for use in building. It does not apply to panes having an area less than 0,05 m2.

This part of this European Standard specifies performance requirements for laminated glass as defined in prEN ISO 12543-1.

This part of this European Standard specifies test methods in respect of resistance to high temperature, humidity and radiation for laminated glass and laminated safety glass for use in building.

This part of this European Standard defines terms and describes component parts for laminated glass and laminated safety glass for use in building.

ISO 12543-2:2004 specifies performance requirements for laminated safety glass.

This part of this European Standard specifies defects of finished sizes and test methods with regard to the appearance when looking through the glass. Special attention is paid to acceptability criteria in the vision area. These criteria apply to products at the time of supply.