CEN/TC 182/WG 7 - JWG CEN/TC 182/CEN/TC 54 Pressure vessels for refrigerating systems
Standardization of pressure vessels and piping for refrigerating systems.
JWG CEN/TC 182/CEN/TC 54 Pressure vessels for refrigerating systems
Standardization of pressure vessels and piping for refrigerating systems.
General Information
1.1 This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary piping intended for use in refrigerating systems, heat pumps and secondary cooling and heating systems. These refrigerating systems and heat pump systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
1.2 This document applies to piping, including welded or brazed attachments up to and including the flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
1.3 This document applies to the selection, application and installation of safety accessories intended to protect the piping during the various phases of the refrigeration cycle.
1.4 This document applies to the following piping:
- heat exchanger consisting of piping for the purpose of cooling or heating air where piping aspects are predominant;
- piping incorporated into an assembly (e.g. self-contained system, condensing unit);
- field erected piping.
1.5 This document applies to piping with an internal pressure down to -1 bar, to account for the evacuation of the piping prior to charging with refrigerant.
1.6 This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445 3:2014/A5:2018 associated with refrigerating systems. It applies to piping subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 14276-1:2020 or as specified in this document. In addition, piping designed to this document will have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, the EN 13480 series can be used for the design construction and inspection of the piping. Under these circumstances, the unique nature of a refrigerating plant, as indicated in the introduction of EN 14276-1:2020, will also be taken into account.
1.7 This document applies to piping where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and in EN 14276-1:2020.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps. These systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
This document applies to vessels, including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
This document applies to pressure vessels with an internal pressure down to -1 bar, to account for the evacuation of the vessel prior to charging with refrigerant.
This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445-3:2014 associated with refrigerating systems. It applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 13445-2:2014 and EN 13445-3:20141 or as specified in this document. In addition, vessels designed to this document can have a maximum allowable temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, it is important that the EN 13445 series be used for the design, construction and inspection of the vessel. Under these circumstances, it is important that the unique nature of refrigerating plant, as indicated in the introduction to this document, also be taken into account.
It is important that pressure vessels used in refrigerating systems and heat pumps of category less than II as defined in Annex H comply with other relevant clauses of EN 378-2:2016 for vessels.
This document applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and Annex I of this document.
This document does not apply to vessels of the following types:
- vessels of riveted construction;
- multi-layered, autofrettaged or prestressed vessels;
- vessels directly heated by a flame;
- "roll bond" heat exchangers.
- Standard106 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary piping intended for use in refrigerating systems, heat pumps and secondary cooling and heating systems. These refrigerating systems and heat pump systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
1.2 This document applies to piping, including welded or brazed attachments up to and including the flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
1.3 This document applies to the selection, application and installation of safety accessories intended to protect the piping during the various phases of the refrigeration cycle.
1.4 This document applies to the following piping:
- heat exchanger consisting of piping for the purpose of cooling or heating air where piping aspects are predominant;
- piping incorporated into an assembly (e.g. self-contained system, condensing unit);
- field erected piping.
1.5 This document applies to piping with an internal pressure down to -1 bar, to account for the evacuation of the piping prior to charging with refrigerant.
1.6 This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445 3:2014/A5:2018 associated with refrigerating systems. It applies to piping subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 14276-1:2020 or as specified in this document. In addition, piping designed to this document will have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, the EN 13480 series can be used for the design construction and inspection of the piping. Under these circumstances, the unique nature of a refrigerating plant, as indicated in the introduction of EN 14276-1:2020, will also be taken into account.
1.7 This document applies to piping where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and in EN 14276-1:2020.
- Draft38 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps. These systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
This document applies to vessels, including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
This document applies to pressure vessels with an internal pressure down to -1 bar, to account for the evacuation of the vessel prior to charging with refrigerant.
This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445-3:2014 associated with refrigerating systems. It applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 13445-2:2014 and EN 13445-3:20141 or as specified in this document. In addition, vessels designed to this document can have a maximum allowable temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, it is important that the EN 13445 series be used for the design, construction and inspection of the vessel. Under these circumstances, it is important that the unique nature of refrigerating plant, as indicated in the introduction to this document, also be taken into account.
It is important that pressure vessels used in refrigerating systems and heat pumps of category less than II as defined in Annex H comply with other relevant clauses of EN 378-2:2016 for vessels.
This document applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and Annex I of this document.
This document does not apply to vessels of the following types:
- vessels of riveted construction;
- multi-layered, autofrettaged or prestressed vessels;
- vessels directly heated by a flame;
- "roll bond" heat exchangers.
- Draft49 pagesEnglish languagesale 10% offe-Library read for1 day
2010-03-29 EMA: Mandate and consultant added following e-mail from PM sent to dataservice on 2010-03-29.
- Draft9 pagesEnglish languagesale 10% offe-Library read for1 day
2010-03-29 EMA: Mandate and consultant added following e-mail from PM sent to dataservice on 2010-03-29.
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies the requirements for material, design, manufacturing, testing and documentation for stationary piping intended for use in refrigerating systems, heat pumps and secondary cooling and heating systems. These refrigerating systems and heat pump systems are referenced in this standard as refrigerating systems as defined in EN 378-1.
1.2 This European Standard applies to piping including welded or brazed attachments up to and including the flanges, screwed, welded or brazed connectors or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
1.3 This European Standard applies to the selection, application and installation of safety accessories intended to protect the piping during the various phases of the refrigeration cycle.
1.4 This European Standard applies to the following piping:
- heat exchanger consisting of piping for the purpose of cooling or heating air where piping aspects are predominant;
- piping incorporated into an assembly (e.g. self contained system, condensing unit);
- field erected piping.
1.5 This European Standard applies to piping with an internal pressure down to - 1 bar, to account for the evacuation of the piping prior to charging with refrigerant.
1.6 This European Standard applies to both the mechanical loading conditions and thermal conditions as defined in EN 13480-3 associated with refrigerating systems. It applies to piping subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 14276-1 or as specified in this European Standard. In addition piping designed to this standard needs to have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 64 bar. Outside of these limits, EN 13480 should be used for the design construction and inspection of the piping. Under these circumstances the unique nature of a refrigerating plant, as indicated in the introdu
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps. These systems are referenced in this standard as refrigerating systems as defined in EN 378-1.
This European Standard applies to vessels including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
This European Standard applies to pressure vessels with an internal pressure down to - 1 bar, to account for the evacuation of the vessel prior to charging with refrigerant.
This European Standard applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445-3 associated with refrigerating systems. It applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 13445-2 and EN 13445-3 or as specified in this standard. In addition vessels designed to this standard should have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 64 bars. Outside of these limits, it is important that EN 13445 be used for the design, construction and inspection of the vessel. Under these circumstances it is important that the unique nature of refrigerating plant, as indicated in the introduction to this standard, also be taken into account.
It is important that pressure vessels used in refrigerating systems and heat pumps of category less than II as defined in Annex H comply with other relevant clauses of EN 378-2 for vessels.
This European Standard applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and Annex I of this standard.
This European Standard does not apply to vessels of the
- Standard86 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies the requirements for material, design, manufacturing, testing and documentation for stationary piping intended for use in refrigerating systems, heat pumps and secondary cooling and heating systems. These refrigerating systems and heat pump systems are referenced in this standard as refrigerating systems as defined in EN 378-1.
1.2 This European Standard applies to piping including welded or brazed attachments up to and including the flanges, screwed, welded or brazed connectors or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
1.3 This European Standard applies to the selection, application and installation of safety accessories intended to protect the piping during the various phases of the refrigeration cycle.
1.4 This European Standard applies to the following piping:
heat exchanger consisting of piping for the purpose of cooling or heating air where piping aspects are predominant;
piping incorporated into an assembly (e.g. self contained system, condensing unit);
field erected piping.
1.5 This European Standard applies to piping with an internal pressure down to – 1 bar, to account for the evacuation of the piping prior to charging with refrigerant.
1.6 This European Standard applies to both the mechanical loading conditions and thermal conditions as defined in EN 13480-3 associated with refrigerating systems. It applies to piping subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 14276-1 or as specified in this European Standard. In addition piping designed to this standard needs to have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 64 bar. Outside of these limits, EN 13480 should be used for the design construction and inspection of the piping. Under these circumstances the unique nature of a refrigerating plant, as indicated in the introdu
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps. These systems are refer-enced in this standard as refrigerating systems as defined in EN 378-1.
This European Standard applies to vessels including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
This European Standard applies to pressure vessels with an internal pressure down to – 1 bar, to account for the evacuation of the vessel prior to charging with refrigerant.
This European Standard applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445-3 associated with refrigerating systems. It applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 13445-2 and EN 13445-3 or as specified in this standard. In addition vessels designed to this standard should have a maximum design tempera-ture not exceeding 200 °C and a maximum design pressure not exceeding 64 bars. Outside of these limits, it is es-sential that EN 13445 be used for the design, construction and inspection of the vessel. Under these circumstances it is important that the unique nature of refrigerating plant, as indicated in the introduction to this standard, also be taken into account.
It is important that pressure vessels used in refrigerating systems and heat pumps of category less than II as de-fined in Annex H comply with other relevant clauses of EN 378-2 for vessels.
This European Standard applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and Annex I of this standard.
This European Standard does not apply to vessels of t
- Standard85 pagesEnglish languagesale 10% offe-Library read for1 day