ISO/TC 72/SC 1 - Spinning preparatory, spinning, twisting and winding machinery and accessories

ISO 368:2017 specifies the dimensions (length and inner diameter) and permissible total run-out tolerances of tubes with taper 1:38 and 1:64 for ring-spinning, doubling and twisting spindles used in the textile industry. It also specifies the dimensions and tolerances of the gauges for checking the tubes.

ISO 96-1:2016 specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the appropriate travellers for flange rings employed on ring spinning and ring twisting machines. It also specifies the method of designation of the travellers.

ISO 18600:2015 defines terms of the card with a web-forming method using staple fibres for non-woven machinery.

ISO 18599:2015 specifies the dimensions and execution of strips for water nozzle solidification including their designation.

ISO 21485:2013 establishes a vocabulary of terms related to, and the principles of construction of, draw frames and their components, used for cotton spinning in the textile industry.

ISO 16853:2010 specifies the main dimensions, with tolerances, of rectangular sliver cans used in the textile industry. It also gives information about the right-angle position of cans according to ISO 1101.

ISO 96-2:2009 specifies the principal dimensions of HZ- and J-rings, and the mass and tolerance on the mass, of the appropriate travellers for HZ- and J-rings employed on ring spinning and ring twisting machines. It also specifies the method of designation of the travellers.

ISO 28239:2008 establishes a vocabulary of terms related to, and the principles of construction of, openers and cleaners used in the textile industry in the preparation for spinning of cotton and other staple fibres.

ISO 26243:2007 specifies terms and definitions for the card with regard to spinning procedure for cotton and other staple fibres.

ISO 93-1:2006 specifies the main dimensions of cylindrical sliver cans used in the textile industry.

ISO 93-2:2006 specifies the principal features of spring bottoms -- with and without pre-tension -- for cylindrical sliver cans, as specified in ISO 93-1, used in the textile industry.

ISO 9903-1:2003 specifies the main dimensions for section wires for metallic card clothing with foot without interlocking or interchaining.

ISO 9903-2:2003 specifies the main dimensions for section wires for metallic card clothing with interchaining foot.

This International Standard specifies the main dimensions of coverings for ready-for-use top rollers (synthetic coverings). It is applicable to spinning preparatory and spinning machinery.

This International Standard specifies the dimensions, characteristics and designations of steel pins recommended for spinning preparatory and spinning machinery.

Specifies the main dimensions, tolerances and designation of cones for cross winding with a half angle of cone 4° 20 ' . Furthermore, directives are given for the characteristics of cones and for the control of the diameters and lengths of the cone.

Specifies the main dimensions, tolerances and designation of cones for cross winding for dyeing purposes with a half angle of cone 4° 20 ' . Furthermore, directives are given for the characteristics of cones and for the control of the diameters and lengths of the cone.

Specifies the main dimensions, tolerances and designation of cones for cross winding with a half angle of cone 5° 57 ' . Furthermore, directives are given for the characteristics of cones and for the control of the diameters and lengths of the cone.

Contains recommended types of cones (values of half angles, lengths and large inner diameters) used in the field of textile industry.

Specifies the main dimensions, tolerances and designation of cones for cross winding with a half angle of cone 3° 30 ' . Furthermore, directives are given for the characteristics of cones and for the control of the diameters and lengths of the cone.

Describes details for packaging and labelling of cotton bales.

Cancels and replaces the first edition (1984). Specifies the main dimensions, tolerances and designation of cylindrical tubes for tape yarns. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Cancels and replaces the first edition (1982). Specifies the main dimensions of cylindrical tubes used in the field of textile machinery.

Cancels and replaces the first edition (1981). Specifies the main dimensions, tolerances and designation of cylindrical tubes for open-end spinning. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Specifies the main dimensions, tolerances and designation of cylindrical tubes of perforated tubes for cheese dyeing. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Intended to reduce the innumerable dimensions of cotton bales. Standardization of the dimensions of bales of man-made fibres might be the subject of a future International Standard. Lays down the nominal overall dimensions and the bale density of banded cotton bales. Applicable to the shaping and forming, the transport and opening of the bales. Not applicable to wrapping, banding, and marking of bales.

Specifies the spindle gauges for the machines named. The spindle gauge is the distance between the axes of two adjoining spindles. The sizes of spindle gauges are shown in a table. - Replaces the first edition (ISO 94-1972).

Specifies the numbering and the dimensions for the two types of card gauges currently used to set the distance between the working elements of cards. Dimensions of gauges, typ A are shown in table 1, numbering and thickness of the gauges are contained in table 2. - Replaces the first edition (ISO 2572-1974)

Figure 1a shows a flyer bobbin of the type with shoulder, figure 1b gives a flyer bobbin of the type without shoulder. Table 1 contains the main dimensions and tolerances of bobbins with shoulder, table 2 those of bobbins without shoulder. - Replaces ISO Recommendations R 344/1-1963 and R 344/2-1969 and constitutes its technical revision.

Lays down the dimensions, shapes and sections of wires for flexible card clothings. A table comprises values for card wire size and for card wire section (for example, round, biconvex and so on).

Defines left and right sides of single-sided machines, double-sided machines with lateral driving unit and double-sided machines with centre driving unit.

To determine the side of a spinning machine with flow of the material in one single direction, the observer looks against this flow. Examples: Blowroom machines, cards, crawing frames and fly frames. Definitions of the side of a spinning machine with flow of the material in various directions and of a double-sided spinning machine are given in detail.

ISO 96-1:2009 specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the appropriate travellers for flange rings employed on ring spinning and ring twisting machines. It also specifies the designation method for the travellers.

ISO 21485:2006 establishes a vocabulary of terms related to, and the principles of construction for, draw frames and their components, used for cotton spinning in the textile industry.

ISO 368:2006 specifies the dimensions (length and inner diameter) and permissible total run-out of tubes with taper 1:38 and 1:64 for ring-spinning, doubling and twisting spindles used in the textile industry. It also specifies the dimensions and tolerances of the gauges for checking the tubes.

ISO 16853:2003 specifies the main dimensions, with tolerances, of rectangular sliver cans used in the textile industry. It also gives information about the right-angle position of cans.

Cancels and replaces the first edition (1989). Specifies the main dimensions, tolerances and designation of cylindrical tubes for textured yarns. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Gives the main dimensions, tolerances and designation of cylindrical tubes for gross-wound packages in winding and twisting. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Gives the main dimensions, tolerances and designation of cylindrical tubes for continuous spin-drawn synthetic filament yarns. Gives directives for the characteristics of tubes and for the control of the inner diameter and length of the tube.

Specifies the overall dimensions of banded bales of man-made staple fibres. These dimensions allow for an optimum utilisation of the loading space of freight containers and trucks.

Specifies the principal dimensions of HZCH-, HZ- and J-rings, the mass, the tolerance on the mass, wire section, range of numbers of the appropriate travellers for these rings. Includes the designation method for the travellers.

Specifies the principal dimensions of T-rings, the mass, the tolerance on the mass, wire section, range of numbers of the appropriate travellers for these rings. Includes the designation method for the travellers.

Specifies the dimensions, tolerances, hardness and designation of three types of wires.

Specifies the dimensions (length and inner diameter) and permissible total run-out of tubes as well as the dimensions and tolerances of the gauges for checking the tubes. This third edition cancels and replaces the second edition (1982).