ISO 368:2017

Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64

ISO 368:2017 specifies the dimensions (length and inner diameter) and permissible total run-out tolerances of tubes with taper 1:38 and 1:64 for ring-spinning, doubling and twisting spindles used in the textile industry. It also specifies the dimensions and tolerances of the gauges for checking the tubes.

Matériel de préparation de filature, de filature et de retordage — Tubes pour broches de continus à filer et à retordre à anneaux, conicité 1:38 et 1:64

General Information

• Status: Published
• Publication Date: 29-Nov-2017
• ICS: 59.120.10 - Spinning, twisting and texturing machines
• Technical Committee: ISO/TC 72/SC 1 - Spinning preparatory, spinning, twisting and winding machinery and accessories
• Drafting Committee: ISO/TC 72/SC 1 - Spinning preparatory, spinning, twisting and winding machinery and accessories
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 07-Nov-2023

Relations

• Consolidated By: ISO 20884:2019/Amd 1:2021 - Petroleum products — Determination of sulfur content of automotive fuels — Wavelength-dispersive X-ray fluorescence spectrometry — Amendment 1: Addition of the SSD detector to the Monochromatic excitation part of Table 1
• Effective Date: 06-Jun-2022
• Revises: ISO 368:2006 - Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64
• Effective Date: 17-Dec-2016

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 368
Fifth edition
2017-12
Spinning preparatory, spinning and
doubling (twisting) machinery —
Tubes for ring-spinning, doubling and
twisting spindles, taper 1:38 and 1:64
Matériel de préparation de filature, de filature et de retordage —
Tubes pour broches de continus à filer et à retordre à anneaux,
conicité 1:38 et 1:64
Reference number
ISO 368:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 368:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 368:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types, dimensions and tolerances . 1
4.1 Tubes . 1
4.1.1 Tube types . 1
4.1.2 Dimensions . 1
4.1.3 Total run-out tolerance . 1
4.2 Gauges . 1
5 Tubes and gauges . 2
5.1 Tubes . 2
5.2 Gauges . 3
6 Designation . 5
6.1 Tubes . 5
6.2 Gauges . 6
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 368:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member bod
...