ISO 96-1:2009

Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames — Part 1: Flange rings T and SF and their travellers

ISO 96-1:2009 specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the appropriate travellers for flange rings employed on ring spinning and ring twisting machines. It also specifies the designation method for the travellers.

Matériel pour l'industrie textile — Anneaux et curseurs pour machines à filer et à retordre — Partie 1: Anneaux T et SF et leurs curseurs

General Information

• Status: Withdrawn
• Publication Date: 09-Mar-2009
• Withdrawal Date: 09-Mar-2009
• ICS: 59.120.10 - Spinning, twisting and texturing machines
• Technical Committee: ISO/TC 72/SC 1 - Spinning preparatory, spinning, twisting and winding machinery and accessories
• Drafting Committee: ISO/TC 72/SC 1 - Spinning preparatory, spinning, twisting and winding machinery and accessories
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 09-Nov-2016

Relations

• Revised: ISO 96-1:2016 - Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames — Part 1: Flange rings T and SF and their travellers
• Effective Date: 27-Sep-2014
• Revises: ISO 96-1:1992 - Textile machinery and accessories — Rings and travellers for ring spinning and ring doubling frames — Part 1: T-rings and their appropriate travellers
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 96-1
Second edition
2009-03-01


Textile machinery and accessories —
Rings and travellers for ring spinning
and ring twisting frames —
Part 1:
Flange rings T and SF and their travellers
Matériel pour l'industrie textile — Anneaux et curseurs pour machines
à filer et à retordre —
Partie 1: Anneaux T et SF et leurs curseurs





Reference number
ISO 96-1:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 96-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 96-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 96-1 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories,
Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories.
This second edition cancels and replaces the first edition (ISO 96-1:1992), which has been technically revised.
ISO 96 consists of the following parts, under the general title Textile machinery and accessories — Rings and
travellers for ring spinning and ring twisting frames:
⎯ Part 1: Flange rings T and SF and their travellers
⎯ Part 2: HZ- and J-rings and their travellers
© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATI
...