19.060 - Mechanical testing

This document specifies a test method for determining the flex resistance of rubber- or plastics‑coated
fabrics in the folded condition. The test method is applicable only to products which can be clamped in
the test apparatus used and to products with which the fold made in the test specimen can be caused to
move back and forth along the specimen during the test.
The appearance of the test specimen, after completion of either the flex number (see 3.1) or a specified
number of flex cycles, ...view more

ISO 6506-2:2017 specifies methods of direct and indirect verification of testing machines used for determining Brinell hardness in accordance with ISO 6506‑1 and also specifies when these two types of verification have to be performed.
The direct verification involves checking that individual machine performance parameters fall within specified limits whereas the indirect verification utilizes hardness measurements of reference blocks, calibrated in accordance with ISO 6506‑3, to check the mach...view more

This part of IEC 60749 describes a salt atmosphere test that determines the resistance of
semiconductor devices to corrosion. It is an accelerated test that simulates the effects of
severe sea-coast atmosphere on all exposed surfaces. It is only applicable to those devices
specified for a marine environment.
The salt atmosphere test is considered destructive.

ISO 4545-2:2017 specifies the method of verification and calibration of testing machines for determining Knoop hardness for metallic materials in accordance with ISO 4545‑1.
A direct method of verification and calibration is specified for the testing machine, indenter, and the diagonal length measuring system. An indirect verification method using reference blocks is specified for the overall checking of the machine.
If a testing machine is also to be used for other methods of hardness testing...view more

ISO 4545-3:2017 specifies the method for the calibration of reference blocks to be used for the indirect verification of Knoop hardness testing machines as specified in ISO 4545‑2.
The method is applicable only for indentations with long diagonals ≥0,020 mm.

This part of IEC 60794 applies to optical fibre cables for use with telecommunication
equipment and devices employing similar techniques, and to cables having a combination of
both optical fibres and electrical conductors.
The object of this standard is to define test procedures to be used in establishing uniform
requirements for mechanical requirement performance.
Throughout this standard the wording “optical cable” may also include optical fibre units,
microduct fibre units, etc.
Genera...view more

ISO 14577-2:2015 specifies the method of verification and calibration of testing machines for carrying out the instrumented indentation test in accordance with ISO 14577‑1:2015.
It describes a direct verification method for checking the main functions of the testing machine and an indirect verification method suitable for the determination of the repeatability of the testing machine. There is a requirement that the indirect method be used in addition to the direct method and for the periodic ro...view more

This part of IEC 60749 provides a test method to evaluate the endurance of semiconductor
devices used in high temperature and high humidity environments.
This test method is used to evaluate the endurance against corrosion of the metallic
interconnection of chips of semiconductor devices contained in plastic moulded and other
types of packages. It is also used as a means of accelerating the leakage phenomena due to
the moisture penetration through the passivation film and as a pre-condition...view more

ISO 6506-3:2014 specifies a method for the calibration of reference blocks to be used in the indirect verification of Brinell hardness testing machines as described in ISO 6506‑2.
The procedures necessary to ensure metrological traceability of the calibration machine are also specified.

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to define a standard test method to assess the possibility of whisker growth by external mechanical stress on the tin and tin-alloy plated parts of a connector in its application (after wire termination, after soldering, after mounting, mate...view more

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the ability of a fixed male tab and its fixing to withstand a specified bending stress. If so specified in the detail specification, forces other than bending may be applied.

This part of IEC 60512, when required by the detail specification, is used for testing electrical connectors within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the ability of terminations to withstand the mechanical stresses likely to be applied during normal assembly operations.

This part of IEC 60512, when required by the detail specification, is used for testing electrical connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the ability of a contact to withstand a specified bending moment or force. If so specified in the detail specification, forces other than bending may be applied. Although this tes...view more

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the ability of a fixed male tab and its fixing to withstand specified tensile and compressive forces. If so specified in the detail specification, forces other than tension ...view more

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the holding capacity of contacts with resilient features by means of gauges. The test is also applicable to the grounding contact spring, and other similar contact systems, where the ability...view more

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of contacts to resist deformation (damage) from crimping operations. Although this test is intended for cylindrical contacts, especially machined contacts, it is applicabl...view more

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the ability of a fixed male tab and its fixing to withstand specified tensile and compressive forces. If so specified in the detail specification, forces other than tension ...view more

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of an insulation grip to hold the insulation of a cable/wire under specified conditions.

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the holding capacity of grounding contact springs by means of gauges.