83.140.30 - Plastics pipes and fittings for non fluid use

This part of ISO 16486 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirement...view more

This part of ISO 16486 specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and require...view more

This part of ISO 16486 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series of standards is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, this document lays down dimensional charac...view more

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, it lays down dimensional characteristics and require...view more

This document specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. This document establishes a calculation and d...view more

This document specifies the endurance test necessary to confirm the ability of hand-operated plastics
valves to withstand prolonged use, with repeated opening and closure. It does not specify the ability of
valves to withstand adverse conditions, in particular those of chemically aggressive fluid media and/or
environments, or excessive fluid velocities and cavitation.
NOTE Concerning the chemical aggression of the materials, a classification table is reported in
ISO/TR 10358[1].
This docum...view more

This document specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore.
This document is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from - 196 °C to + 45 °C.
NOTE   Offshore LNG hose assemblies are also speci...view more

This document specifies the endurance test necessary to confirm the ability of hand-operated plastics valves to withstand prolonged use, with repeated opening and closure. It does not specify the ability of valves to withstand adverse conditions, in particular those of chemically aggressive fluid media and/or environments, or excessive fluid velocities and cavitation. NOTE Concerning the chemical aggression of the materials, a classification table is reported in ISO/TR 10358[1]. This document in...view more

This draft European Standard describes and specifies the characteristics and performance requirements for assemblies made of tubing and hoses complying with EN 16436-1 to be used in the same conditions.
All connections are given in Annex B.
This draft European Standard only defines specific connections which are not defined in other standards (e.g. EN 16129).

This document specifies the requirements and test methods for plastics piping systems intended to be
used for the renovation of underground gas supply networks. It is applicable to pipes and fittings, as
manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or
any sprayed coatings or annular filler.
This document gives the general requirements common to all relevant renovation techniques.

This document, in conjunction with ISO 11299-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of gas supply networks.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable
to polyethylene (PE) pipe of either solid wall single layer or co-extruded layer construction, which is
reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe...view more

This document, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types: PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
PE pipes with co-­‐extruded layers on either or both the outside and inside of the pipe...view more

This document gives requirements for the qualification and manufacture of GRP piping and fittings in
order to enable the purchase of GRP components with known and consistent properties from any source.
It is applicable to qualification procedures, preferred dimensions, quality programmes, component
marking and documentation.
This document is intended to be read in conjunction with ISO 14692-1.

This document defines the applications, pressure rating methodology, the classification of the products
according to application, type of joint and resin matrix and the limitations to both the materials of
construction and the dimensions. It also lists the terms, definitions and symbols used and provides
guidance in the use and interpretation of ISO 14692-2, ISO 14692-3 and ISO 14692-4.
ISO 14692 (all parts) is applicable to GRP piping systems that 1) utilize joints that are capable of
rest...view more

This document gives guidelines for the design of GRP piping systems. The requirements and
recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire
endurance, spread of fire and emissions and control of electrostatic discharge.
This document is intended to be read in conjunction with ISO 14692-1.

This document gives requirements and recommendations for the fabrication, installation, inspection
and maintenance of GRP piping systems for use in oil and natural gas industry processing and utility
service applications. The recommendations apply to delivery, inspection, handling, storage, installation,
system pressure testing, maintenance and repair.
It is intended to be read in conjunction with ISO 14692-1.

ISO 14692-3:2017 gives guidelines for the design of GRP piping systems. The requirements and recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire endurance, spread of fire and emissions and control of electrostatic discharge.
This document is intended to be read in conjunction with ISO 14692‑1.

ISO 14692-4:2017 gives requirements and recommendations for the fabrication, installation, inspection and maintenance of GRP piping systems for use in oil and natural gas industry processing and utility service applications. The recommendations apply to delivery, inspection, handling, storage, installation, system pressure testing, maintenance and repair.
It is intended to be read in conjunction with ISO 14692‑1.

ISO 14692-2:2017 gives requirements for the qualification and manufacture of GRP piping and fittings in order to enable the purchase of GRP components with known and consistent properties from any source.
It is applicable to qualification procedures, preferred dimensions, quality programmes, component marking and documentation.
ISO 14692-2:2017 is intended to be read in conjunction with ISO 14692‑1.