EN ISO 1403:2019
(Main)Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:2019)
Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:2019)
This document specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 2,5 MPa (25 bar).
These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses.
These hoses can be used with additives which lower the freezing point of water.
Gummischläuche mit Textileinlage für allgemeine Anwendungen mit Wasser - Spezifikation (ISO 1403:2019)
Dieses Dokument legt die Anforderungen an drei Typen von Gummischläuchen mit Textileinlage für allgemeine Anwendungen mit Wasser in einem Betriebstemperaturbereich von −25 °C bis +70 °C und bei einem maximalen Arbeitsdruck bis zu 2,5 MPa (25 bar) fest.
Diese Schläuche sind nicht für Anwendungen zur Förderung von Trinkwasser, den Zulauf an Waschmaschinen, als Feuerwehrschläuche, für spezielle Landwirtschaftsmaschinen und als faltbare Schläuche vorgesehen.
Diese Schläuche können angewendet werden, wenn das Wasser Zusätze zur Gefrierpunktserniedrigung enthält.
Tuyaux en caoutchouc à armature textile d'usage général pour l'eau - Spécifications (ISO 1403:2019)
Le présent document spécifie les exigences pour trois types de tuyaux en caoutchouc à armature textile d'usage général pour l'eau, sur une plage de températures de service de −25 °C à +70 °C et pour une pression maximale de service jusqu'à 2,5 MPa (25 bar).
Ces tuyaux ne sont pas destinés au transport d'eau potable, au raccordement de machine à laver, aux machines agricoles spéciales et ne sont pas destinés à être utilisés comme tuyaux d'arrosage souple ou comme tuyaux d'incendie.
Ces tuyaux peuvent être utilisés avec des additifs abaissant la température de congélation de l'eau.
S tekstilom ojačene gumene cevi za splošno namensko uporabo vode - Specifikacija (ISO 1403:2019)
Ta dokument določa zahteve za tri vrste s tekstilom ojačenih gumenih cevi za splošno namensko uporabo vode z delovno temperaturo od –25 °C do +70 °C in največjim delovnim tlakom do 2,5 MPa (25 barov). Te cevi niso namenjene za prenos pitne vode, za dovode pralnih strojev, za gasilske cevi, za cevi za posebne kmetijske stroje ali za vodne cevi, ki jih je mogoče zložiti. Te cevi je mogoče uporabljati z dodatki, ki znižujejo ledišče vode.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2019
Nadomešča:
SIST EN ISO 1403:2009
S tekstilom ojačene gumene cevi za splošno namensko uporabo vode -
Specifikacija (ISO 1403:2019)
Rubber hoses, textile-reinforced, for general-purpose water applications - Specification
(ISO 1403:2019)
Gummischläuche mit Textileinlage für allgemeine Anwendungen mit Wasser -
Anforderung (ISO 1403:2019)
Tuyaux en caoutchouc à armature textile d'usage général pour l'eau - Spécifications
(ISO 1403:2019)
Ta slovenski standard je istoveten z: EN ISO 1403:2019
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 1403
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2019
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 1403:2008
English Version
Rubber hoses, textile-reinforced, for general-purpose
water applications - Specification (ISO 1403:2019)
Tuyaux en caoutchouc à armature textile d'usage Gummischläuche mit Textileinlage für allgemeine
général pour l'eau - Spécifications (ISO 1403:2019) Anwendungen mit Wasser - Anforderung (ISO
1403:2019)
This European Standard was approved by CEN on 1 July 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1403:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 1403:2019) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall
be withdrawn at the latest by March 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1403:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1403:2019 has been approved by CEN as EN ISO 1403:2019 without any modification.
INTERNATIONAL ISO
STANDARD 1403
Fifth edition
2019-07
Rubber hoses, textile-reinforced, for
general-purpose water applications —
Specification
Tuyaux en caoutchouc à armature textile d'usage général pour
l'eau — Spécifications
Reference number
ISO 1403:2019(E)
©
ISO 2019
ISO 1403:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 1403:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Materials and construction . 2
6 Dimensions . 2
6.1 Inside diameters and tolerances. 2
6.2 Concentricity. 2
6.3 Tolerance on length . 2
6.4 Minimum thickness of lining and cover . 2
7 Physical properties . 3
7.1 Rubber compounds . 3
7.2 Finished hose . 3
8 Marking . 4
ISO 1403:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.