25.120.10 - Forging equipment. Presses. Shears

This document specifies the dimensions and tolerances of guide pillars, type D, end-locking pillar with flange, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.

This document specifies the dimensions and tolerances of guide pillars, type B, intended for use in press tools. These guide pillars can be end-locking, type B1 (see Figure 1), or end-locking with lubrication grooves, type B2 (see Figure 2). It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.

This document specifies the dimensions and tolerances of guide pillars, type C, with taper lead and bush, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.

This document, in addition to ISO 16092-1, specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of the following groups of mechanical presses and mechanical press production systems:
— Group 1: Presses with a part revolution clutch(es);
— Group 2: Presses with a servo drive system (Mechanical servo presses).
NOTE 1 Requirements in this document are essentially applicable to both groups of the mechanical press. If a requir...view more

This document establishes the terms and definitions of the main types of tools for pressing, their features and dimensional characteristics. Some of these terms refer to components whose functions are shown in Figure 1, Figure 2 and Annex A. This document is intended to serve as a reference for users and manufacturers of tools for pressing. This document is used for understanding of technical terms and applicable for communication and trade of tools for pressing. NOTE The figures are given only ...view more

This document establishes the technical specifications for compression springs made from rectangular wires. The parameters set in this document are applicable to springs which are set. This document does not attempt to specify the quality of the springs themselves, nor all of their dimensions (e.g. cross-section), their material or their length of life. The springs are classified into spring rates: light, medium, strong and extra strong. For each spring rate, this document gives a colour code.

This document specifies dimensions for heel guidings in large stamping and forming dies. It also gives example applications and an example for ordering.

This document specifies the dimensions in millimetres, of mounting base plates, of two-part mounting clamps, of flange mounts and front end supports intended for use in press tool together with gas springs in accordance with ISO 11901‑1, ISO 11901‑3 and ISO 11901‑4. It also gives information concerning materials and specifies the designation of the mounting accessories in accordance with this document.

This document specifies dimensions, stroke and forces of spring plungers with steel spring or gas spring. This document applies to spring plungers which are used in tool manufacture for separating the tool and the sheet-metal part after stamping or forming operations. It also gives information concerning their use and installation example of spring plungers steel spring or gas spring.

This standard specifies technical safety requirements and measures to be adopted by persons undertaking the design (as defined in EN 12100), manufacture and supply of hydraulic presses which are intended to work cold metal or material partly of cold metal.
This standard applies in combination with ISO 16092-1. Both parts together cover all significant hazards relevant for hydraulic presses which are intended to work cold metal or material partly of cold metal, when they are used as intended and...view more

This International standard specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of presses and ancillary devices which are intended to work cold metal or material partly of cold metal.
The requirements in this International standard take account of intended use, as defined in 3.22 of ISO 12100-1:2003. This standard presumes access to the press from all directions, deals with the hazards during the various phases of the life...view more

ISO 16092-3:2017, in addition to ISO 16092‑1, specifies the technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of hydraulic presses which are intended to work cold metal or material partly made up of cold metal.
The presses covered by this document range in size from small high-speed machines with a single operator producing small workpieces to large relatively slow-speed machines with several operators and large complex workpieces...view more

ISO 16092-1:2017 specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of presses which are intended to work cold metal or material partly of cold metal, but which can be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather, etc.).
NOTE 1 The design of a machine includes the study of the machine itself, taking into account all phases of the "life" of the machine mentioned in ISO 12100:...view more

This part of IEC 62841 applies to hand-held shears and nibblers.

This European Standard applies to the tyre curing presses as defined in 3.36 having the following configuration.
-  Crossing flow tyre curing presses, with two cavities with:
   -  common curing cycle and common safeguarding; or
   -  independent curing cycles and common safeguarding; or
   -  independent curing cycles and independent safeguarding.
-  Tyre curing presses with one cavity.
-  Tyre curing presses with automatic rear feeding and discharge.
The requirements and/or safety meas...view more

EN 16500 specifies the safety requirements for the design, manufacture and information for safe use of vertical baling presses for compacting waste material or recyclable fractions (e. g. paper, plastics, textiles, cans, cardboard, mixed waste), hereafter referred to as materials. This standard covers vertical baling presses: - that are manually or mechanically fed; and - with fixed enclosed baling chambers (single or multiple chamber presses); and - with a mechanically, hydraulically or pneumat...view more

This European Standard specifies the safety requirements for the design, manufacture and information for safe use of vertical baling presses for compacting waste material or recyclable fractions (e. g. paper, plastics, textiles, cans, cardboard, mixed waste), hereafter referred to as materials.
This standard covers vertical baling presses:
-   that are manually or mechanically fed; and
-   with fixed enclosed baling chambers (single or multiple chamber presses); and
-   with a mechanically, hydrau...view more

EN 289 specifies the essential safety requirements for compression moulding machines and transfer moulding machines for the moulding of plastics and/or rubber with a closing movement more than 6 mm. In this document a compression moulding machine or transfer moulding machine as described above is designated by the term “press”. This document deals with all significant hazards, hazardous situations and events relevant to presses, when they are used as intended and under conditions of misuse which...view more

ISO 11901-4:2014 specifies the dimensions (in millimetres), nominal initial forces and types of gas springs. It is applicable to gas springs with increased spring force and same built height of type 10 000 to 95 000, pressurized with nitrogen with a nominal initial force of between 10 000 N ± 5 % and 95 000 N ± 5 %, for use in press tools. It also specifies marking, technical delivery conditions and designation.

ISO 11901-3:2014 specifies the dimensions (in millimetres), nominal initial forces and types of gas springs. It is applicable to gas springs with increased spring force and compact built height of type 1 700 to 200 000, pressurized with nitrogen with a nominal initial force of between 1 700 N ± 5 % and 200 000 N ± 5 %, for use in press tools. It also specifies marking, technical delivery conditions and designation.