75.180.30 - Volumetric equipment and measurements

This document establishes a common basis for, and assistance in, the classification of applications and multiphase meters, as well as guidance and recommendations for the implementation and use of such meters. The so-called in-line multiphase flow meters (MPFMs) that directly measure the oil, water and gas flow rates, as well as the partial- and full-separation MPFMs are the main focus of this document. Conventional two- or three-phase separators are not included in this document. Only limited r...view more

EN-ISO 8222 describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications.This document excludes measures for cryogenic liquids and pressurized measures as used for...view more

This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications.
This document excludes measures for cryogenic liquids and pressurized measures as used...view more

This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications. This document excludes measures for cryogenic liquids and pressurized measures as used ...view more

This International Standard specifies the methodology for the regular monitoring of the test method
precision achieved versus precision published in the standard test method using data from Proficiency
Testing Programs (PTP) supported by the regular users of standard test methods.
The procedures in this International Standard are designed specifically for PTPs conducted on standard
test methods for petroleum and petroleum related products, which are presumed to be homogeneous.
The procedure...view more

This document specifies procedures and requirements for the transfer of bunkers to vessels involving bunker tankers, road tankers and shore pipelines. It is applicable to pre-delivery, delivery and post-delivery checks and documentation.

This document specifies the metrological and technical requirements for flowmeters intended to be used for the dynamic measurement of liquefied natural gas (LNG) and other refrigerated hydrocarbon fluids. For LNG static volume measurement used in custody transfer, see ISO 10976. This document sets the best practice for the proper selection and installation of flowmeters in cryogenic applications and identifies the specific issues that can affect the performance of the flowmeter in use. Moreover,...view more

This document specifies the methodology for the design of an Interlaboratory Study (ILS) and
calculation of precision estimates of a test method specified by the study. In particular, it defines the
relevant statistical terms (Clause 3), the procedures to be adopted in the planning of ILS to determine
the precision of a test method (Clause 4), and the method of calculating the precision from the results of
such a study (Clauses 5 and 6).
The procedures in this document have been designed sp...view more

This document specifies the methodology for the application of precision estimates of a test method
derived from ISO 4259-1. In particular, it defines the procedures for setting the property specification
limits based upon test method precision where the property is determined using a specific test method,
and in determining the specification conformance status when there are conflicting results between
supplier and receiver. Other applications of this test method precision are briefly descr...view more

This document refers to temperature volume correction factors, which allow users to convert volumes,
measured at ambient conditions, to those at reference conditions for transactional purposes. This
document also refers to compressibility factors required to correct hydrocarbon volumes measured
under pressure to the corresponding volumes at the equilibrium pressure for the measured
temperature.
Table 1 shows the defining limits and their associated units of correction factors referenced in ...view more

This document specifies the methodology for the application of precision estimates of a test method
derived from ISO 4259-1. In particular, it defines the procedures for setting the property specification
limits based upon test method precision where the property is determined using a specific test method,
and in determining the specification conformance status when there are conflicting results between
supplier and receiver. Other applications of this test method precision are briefly descr...view more

This document specifies the methodology for the design of an Interlaboratory Study (ILS) and
calculation of precision estimates of a test method specified by the study. In particular, it defines the
relevant statistical terms (Clause 3), the procedures to be adopted in the planning of ILS to determine
the precision of a test method (Clause 4), and the method of calculating the precision from the results of
such a study (Clauses 5 and 6).
The procedures in this document have been designed sp...view more

ISO 2714:2017 describes and discusses the characteristics of displacement flowmeters. Attention is given to the factors to be considered in the application of positive displacement meters to liquid metering. These include the properties and nature of the liquid to be metered, the correct installation and operation of the meter, environmental effects, and the wide choice of secondary and ancillary equipment. Aspects of meter proving and maintenance are also discussed. ISO 2714:2017 is applicable ...view more

ISO 2715:2017 describes and discusses the characteristics of turbine flowmeters. Attention is given to the factors to be considered in the application of turbine meters to liquid metering. These include the properties and nature of the liquid to be metered, the correct installation and operation of the meter, environmental effects, and the wide choice of secondary and ancillary equipment. Aspects of meter proving and maintenance are also discussed. ISO 2715:2017 is applicable to the metering of ...view more

ISO 6578:2017 specifies the calculation procedure to convert the volume of liquefied petroleum gas (LPG) and liquefied natural gas (LNG) under the conditions at the time of measurement to the equivalent volume of liquid or vapour at the standard condition, i.e. 15 °C and 101,325 kPaA, or to the equivalent mass or energy (calorific content). It applies to the quantities of refrigerated hydrocarbon liquids stored in or transferred to/from tanks and measured under static storage conditions. Calcula...view more

ISO 19970:2017 specifies minimum requirements to quantify the boil-off gas (BOG) consumed on liquefied natural gas (LNG) carriers for their own functions, notably for power generation, during cargo transfer operations. BOG in this document refers to the low molecular gas returned from shore tanks to ships' tanks and the gas produced in ships' cargo tanks. ISO 19970:2017 provides requirements for the metering of BOG and the subsequent calorific value calculations which can be taken into account w...view more

ISO 91:2017 refers to temperature volume correction factors, which allow users to convert volumes, measured at ambient conditions, to those at reference conditions for transactional purposes. This document also refers to compressibility factors required to correct hydrocarbon volumes measured under pressure to the corresponding volumes at the equilibrium pressure for the measured temperature.

ISO 12917-1:2017 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at fixed locations. The methods in this document are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks. ISO 12917-1:2017 is applicable to tanks inclined from the horizontal, provide...view more

ISO 29945:2016 specifies a manual sampling method for refrigerated liquefied DME at terminals in both loading and unloading ports along with precautions. ISO 29945:2016 does not include recommendations for the location of a sampling point in a line or vessel. ISO 29945:2016 is also applicable to the following cases, with necessary modifications: - sampling of DME on board liquefied gas tankers where appropriate sampling apparatus is provided; - sampling of other refrigerated, non-petroleum-based...view more

This European Standard specifies functional requirements for the design, construction, testing, commissioning/decommissioning, operation, maintenance and where appropriate calibration, together with suitable documented provisions for all new gas measuring systems and any major changes of existing systems.
This European Standard also specifies accuracy classes of measuring systems and thresholds applicable to these classes. Demonstration of compliance is achieved through the selection, installat...view more