iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3548-09(2023)

(Specification)

Standard Specification for Ethyl Acrylate

Standard Specification for Ethyl Acrylate

ABSTRACT
This specification establishes the properties and requirements for ethyl acrylate for use in paint, varnish, lacquer, and related products. Specimens shall be sampled, undergo chemical tests, and conform accordingly to purity, water content, color, acidity, and methyl ether of hydroquinone content requirements.
SCOPE
1.1 This specification covers ethyl acrylate (99 % grade) for use in paint, varnish, lacquer, and related products.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specification hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 4.1.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Jun-2023
ICS
83.080.20 - Thermoplastic materials
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.35 - Solvents, Plasticizers, and Chemical Intermediates
Current Stage
Ref Project

Relations

Refers
ASTM D1613-06(2012) - Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products
Effective Date
01-Jun-2012
Refers
ASTM D5386-10 - Standard Test Method for Color of Liquids Using Tristimulus Colorimetry
Effective Date
01-Jan-2010
Refers
ASTM E29-08 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-Oct-2008
Refers
ASTM D1364-02(2007) - Standard Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method)
Effective Date
01-Jun-2007
Refers
ASTM E29-06b - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
15-Nov-2006
Refers
ASTM E29-06a - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
15-Sep-2006
Refers
ASTM D3125-06 - Standard Test Method for Monomethyl Ether of Hydroquinone in Colorless Monomeric Acrylate Esters and Acrylic Acid
Effective Date
01-Jun-2006
Refers
ASTM E29-06 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-May-2006
Refers
ASTM D1613-06 - Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products
Effective Date
01-Apr-2006
Refers
ASTM D5386-05 - Standard Test Method for Color of Liquids Using Tristimulus Colorimetry
Effective Date
15-Oct-2005
Refers
ASTM D1209-05 - Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
Effective Date
15-May-2005
Refers
ASTM D3362-05 - Standard Test Method for Purity of Acrylate Esters by Gas Chromatography (Withdrawn 2011)
Effective Date
15-May-2005
Refers
ASTM D1209-05e1 - Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
Effective Date
15-May-2005
Refers
ASTM E29-04 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-Dec-2004
Refers
ASTM D5386-04 - Standard Test Method for Color of Liquids Using Tristimulus Colorimetry
Effective Date
01-Jan-2004

Buy Standard

ASTM D3548-09(2023) - Standard Specification for Ethyl AcrylateASTM D3548-09(2023) - Standard Specification for Ethyl Acrylate
PreviousNext
Technical specification
ASTM D3548-09(2023) - Standard Specification for Ethyl Acrylate
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3548 − 09 (Reapproved 2023)
Standard Specification for
Ethyl Acrylate
This standard is issued under the fixed designation D3548; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1364 Test Method for Water in Volatile Solvents (Karl
Fischer Reagent Titration Method)
1.1 This specification covers ethyl acrylate (99 % grade) for
D1613 Test Method for Acidity in Volatile Solvents and
use in paint, varnish, lacquer, and related products.
Chemical Intermediates Used in Paint, Varnish, Lacquer,
1.2 The following applies to all specified limits in this
and Related Products
standard; for purposes of determining conformance with this
D3125 Test Method for Monomethyl Ether of Hydroquinone
standard, an observed value or a calculated value shall be
in Colorless Monomeric Acrylate Esters and Acrylic Acid
rounded off “to the nearest unit” in the last right-hand digit
(Withdrawn 2021)
used in expressing the specification limit, in accordance with
D3362 Test Method for Purity of Acrylate Esters by Gas
the rounding-off method of Practice E29.
Chromatography (Withdrawn 2011)
1.3 The values stated in SI units are to be regarded as D5386 Test Method for Color of Liquids Using Tristimulus
Colorimetry
standard. No other units of measurement are included in this
standard. E29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications
1.4 For specification hazard information and guidance, see
E300 Practice for Sampling Industrial Chemicals
the supplier’s Safety Data Sheet for materials listed in this
2.2 U.S. Federal Specification:
specification.
PPP-C-2020 Packaging of Chemicals, Liquid, Dry, and Paste
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Properties
responsibility of the user of this standard to establish appro-
3.1 Ethyl acrylate shall conform to the following require-
priate safety, health, and environmental practices and deter-
ments:
mine the applicability of regulatory limitations prior to use.
Purity wt % as ethyl acrylate, min 99.5
Specific hazard statements are given in 4.1.
Water wt %, max 0.08
1.6 This international standard was developed in accor-
Color, Pt-Co scale, max (Note 1) 10 in bulk shipments, 20 in drum
dance with internationally recognized principles on standard-
shipments
Acidity (free acid as acrylic acid) 0.008
ization established in the Decision on Principles for the
wt %, max
Development of International Standards, Guides and Recom-
A
Methyl ether of hydroquinone wppm, min 10
mendations issued by the World Trade Organization Technical
A
Barriers to Trade (TBT) Committee.
or as agreed upon between the purchaser and the manufacturer. Lower levels
are not recommended for safety reasons.
2. Referenced Documents
NOTE 1—Instrumental Pt-Co color determined by Test Method D5386
2 have been shown to have no statistically significant difference from Pt-Co
2.1 ASTM Standards:
color determined by Test Method D1209. However, it is not known
D1209 Test Method for Color of Clear Liquids (Platinum-
whether ethyl acrylate was part of the sample set included in the
Cobalt Scale)
interlaboratory study.
4. Precaution
4.1 Ethyl acrylate samples should be stored in amber bottles
This specification is under
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6267/D6267M-13(2022)(Test Method)
Standard Test Method for Apparent Viscosity of Hydrocarbon Resins at Elevated Temperatures

SIGNIFICANCE AND USE
5.1 This test method is used to measure the apparent viscosity of hydrocarbon resins at elevated temperatures. Elevated temperature viscosity values of a hydrocarbon resin may be related to the properties of coatings, adhesives and the like, containing such a resin.  
5.2 For hydrocarbon resins, values of apparent viscosity will usually be a function of shear rate under the conditions of test. Although the type of viscometer described in this test method operates under conditions of relatively low shear rate, shear rate depends on the spindle and rotational speed selected for a determination; therefore, comparisons between apparent viscosity values should be made only for measurements made with similar viscometers under conditions of equivalent shear rate.
SCOPE
1.1 This test method covers the determination of the apparent viscosity of hydrocarbon resins having apparent viscosities up to 2,000,000 millipascal seconds (mPa·s) (Note 1) at temperatures up to 300 °C [572 °F].
Note 1: The SI unit of (dynamic) viscosity is the pascal second. The centipoise (cP) is one millipascal second (mPa·s) and is frequently used as a viscosity unit.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6604-00(2022)(Practice)
Standard Practice for Glass Transition Temperatures of Hydrocarbon Resins by Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Thermal analysis provides a rapid method for determining transition temperatures in HC resins that possess them.  
5.2 This practice is useful for both quality assurance and research.
SCOPE
1.1 This practice covers determination of glass transition temperatures of hydrocarbon (HC) resins by differential scanning calorimetry (DSC).  
1.2 This practice is applicable to HC resins as defined in Terminology D6640. The normal operating temperature range is from the cryogenic region to approximately 180 °C. The temperature range can be extended.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Further discussion of glass transition can be found in Test Method D3418, and Test Method E1356.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6493-11(2022)(Test Method)
Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus

SIGNIFICANCE AND USE
4.1 For hydrocarbon resins and rosin based resins, softening does not take place at a definite temperature. As the temperature rises, these materials gradually change from brittle solids or very viscous liquids to less viscous liquids. For this reason, determination of the softening point must be made by a fixed, arbitrary, and closely defined method if the results obtained are to be comparable.
SCOPE
1.1 These test methods are intended for determining the softening point of hydrocarbon resins, rosin based resins and similar materials by means of an automated ring-and-ball apparatus. Portions are similar in technical content to the automated-apparatus versions of Test Methods D36, E28, and ISO 4625.  
1.1.1 The ring-and-ball softening point of a hydrocarbon resin and rosin based resins may also be determined with lower precision using the manual ring-and-ball softening point procedure in Test Methods E28.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5897-13(2021)(Test Method)
Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric Titration—Alternative Method

SIGNIFICANCE AND USE
4.1 This test method provides a simpler means for the determination of the hydroxyl content of cellulose esters than the preparation and measurement of the carbanilate derivative described in Test Methods D817 and D871.  
4.2 The hydroxyl content is an important indicator of solubility and reactivity.
SCOPE
1.1 This test method covers a procedure for determining the percent hydroxyl on cellulose esters by potentiometric titration. The typical range of percent hydroxyl measured is 0.7 to 10.0 %.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6579-11(2020)(Practice)
Standard Practice for Molecular Weight Averages and Molecular Weight Distribution of Hydrocarbon, Rosin and Terpene Resins by Size-Exclusion Chromatography

SIGNIFICANCE AND USE
5.1 The MW averages and the MWD are important characteristics of a resin. They may be used for a variety of correlations for fundamental studies, processing, or product applications. The MW and MWD values may also be used for production quality control of resins.  
5.2 Limitations—Comparison of SEC molecular weight values should be made only if the data were obtained under identical chromatographic conditions.
SCOPE
1.1 This practice covers the determination of apparent molecular weight (MW) averages and molecular weight distributions (MWD) for THF-soluble hydrocarbon, rosin and terpene resins by size-exclusion chromatography (SEC). This technique is not absolute; it requires calibration with standards of known molecular weight. This practice is applicable to resins containing molecular-weight components that have elution volumes falling within the elution volume range defined by polystyrene standards.
Note 1: SEC is also known as gel permeation chromatography (GPC).  
1.2 SEC systems employ low-volume liquid chromatography components and columns packed with relatively small (generally 3 to 20 μm) microporous particles. High-performance liquid chromatography instrumentation and automated data handling systems for data acquisition and processing are also required.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6605-06(2020)(Practice)
Standard Practice for Determining the Color Stability of Hydrocarbon Resins After Heating

SIGNIFICANCE AND USE
5.1 This practice is useful for both quality control and research.
SCOPE
1.1 This practice covers determination of the color stability of a hydrocarbon resin by exposure to a specific temperature for a defined time period in a forced-draft oven.  
1.2 Color stability is measured by the change in color of the test resin, measured via the yellowness index color scale, in accordance with Practice E313, or the procedure for Gardner Color, Test Method D6166.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6440-10(2018)(Terminology)
Standard Terminology Relating to Hydrocarbon Resins

SCOPE
1.1 The hydrocarbon resin industry continues to evolve from a source of replacement products for naturally-derived materials to industrial materials that have no naturally-derived counterparts. Along with this changing character of the industry, various manufacturing participants have introduced terms that have led to confusion among both manufacturers and consumers. This terminology standard is intended to alleviate that confusion and promote standard usage of terms in the hydrocarbon resin industry.  
1.2 Resins derived principally from natural terpene fractions are under the jurisdiction of D01.34.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1697-24(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit

ABSTRACT
This specification covers the requirements and test methods for materials, dimensions, workmanship, stiffness factor, extrusion quality, and test procedures for extruded poly(vinyl chloride) (PVC) profile strips used for machine-made field fabrication of spirally wound pipe liners in the rehabilitation of a variety of existing pipelines and conduits including sanitary sewers, storm water sewers, process flow piping, and non-circular pipelines (such as arched or oval shapes and rectangular shapes) under gravity flow conditions. Certification, packaging, and product marking for quality assurance are also considered.
SIGNIFICANCE AND USE
9.1 The requirements of this specification are intended to provide extruded PVC profile strip suitable for the field fabrication of spirally wound liner pipe for the rehabilitation of existing pipelines and conduits conveying sewage, process flow, and storm water under gravity flowconditions.
Note 3: Industrial waste disposal lines should be installed only with the specific approval of the cognizant code authority since chemicals not commonly found in drains and sewers and temperatures in excess of 140 °F (60 °C) may be encountered.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, stiffness factor, extrusion quality, and a form of marking for extruded poly(vinyl chloride) (PVC) profile strips used for machine made field fabrication of spirally wound pipe liners in the rehabilitation of a variety of gravity applications such as sanitary sewers, storm sewers, and process piping in diameters of 6 to 180 in. and for similar sizes of non-circular pipelines such as arched or oval shapes and rectangular shapes.  
1.2 Profile strip produced to this specification is for use in field fabrication of spirally wound liner pipes in nonpressure sewer and conduit rehabilitation, where the spirally wound liner pipe is expanded until it presses against the interior surface of the existing sewer or conduit, or, alternatively, where the spirally wound liner pipe is inserted as a fixed diameter into the existing sewer or conduit and the annular space between the liner pipe and the existing sewer or conduit is grouted.  
1.3 This specification includes extruded profile strips made only from materials specified in 5.1.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D3679-24(Specification)
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

ABSTRACT
This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. The siding shall be made of one or more layers of poly(vinyl chloride) (PVC) compound. Any layers of materials other than poly (vinyl chloride) (PVC) compound shall be kept to less than 20% by volume. The PVC compound when extruded into siding shall maintain uniform color and be free of any visual surface or structural changes, such as peeling, chipping, cracking, flaking, or pitting. The PVC compound shall be compounded so as to provide the heat stability and weather exposure stability required for the siding market application. PVC siding shall not contain elemental lead (Pb) or compounds of that material other than traces incidental to raw materials or the manufacturing process. This limitation applies to both PVC substrate and to any cap or film material. Materials shall be tested and the individual grades shall conform to specified values of length and width, thickness, camber, heat shrinkage, impact resistance, coefficient of linear expansion, gloss, surface distortion, color, weathering, windload resistance, and nail slot allowance for thermal expansion.
SCOPE
1.1 This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.  
1.2 The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.  
1.3 Rigid (unplasticized) PVC soffit is covered in Specification D4477.  
1.4 Siding produced to this specification shall be installed in accordance with the manufacturer's installation instructions for the specific product to be installed.  
Note 1: Information with regard to siding maintenance shall be obtained from the manufacturer.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: There is no known ISO equivalent to this standard.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM D4477-24(Specification)
Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit

ABSTRACT
This specification establishes the physical requirements and test methods for extruded single-wall soffits manufactured from rigid (unplasticized) poly(vinyl chloride) (PVC) compounds. The PVC compound when extruded into soffit shall maintain uniform color and be free of any visual surface or structural changes such as peeling, chipping, cracking, flaking, or pitting. Materials shall undergo testing and shall conform accordingly to requirements in terms of dimension (length, width, and thickness), camber, initial impact resistance, coefficient of linear expansion, gloss, deflection, and color.
SCOPE
1.1 This specification establishes requirements and test methods for the materials, dimensions, camber, impact strength, expansion, and appearance of extruded single-wall soffit manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.  
1.2 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.  
1.3 Soffit produced to this specification shall be installed in accordance with the manufacturer's installation instructions for the specific product to be installed.  
Note 1: Information with regard to soffit maintenance shall be obtained from the manufacturer.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains to the test method portion only, Section 6 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off