ASTM D6837-10
(Test Method)Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine
Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine
SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A baseline calibration oil (hereafter referred to as BC oil) has been established for this test to provide a standard against which all other oils can be compared. The BC oil is an SAE 5W-30 grade fully formulated lubricant. There is a direct correlation of Test Method D6837 (Sequence VIB) Fuel Economy Improvement (FEI) by percent with the fuel economy results obtained from vehicles representative of current production running under the current EPA testing cycles. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. Rather, it was developed to compare a test oil to BC oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VIB test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API Publication 1509.
SAE Classification J304.
SAE Classification J1423. ^SCOPE:
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight of 3856 kg or less. The tests are conducted on a dynamometer test stand using a specified spark-ignition engine with a displacement of 4.6-L. It applies to multiviscosity grade oils used in these applications.
1.2 This test method also provides for the running of an abbreviated length test that is referred to as the VIBSJ. The procedure for VIBSJ is identical to the Sequence VIB with the exception of the items specifically listed in Annex A13. The procedure modifications listed ...
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight of 3856 kg or less. The tests are conducted on a dynamometer test stand using a specified spark-ignition engine with a displacement of 4.6-L. It applies to multiviscosity grade oils used in these applications.
1.2 This test method also provides for the running of an abbreviated length test that is referred to as the VIBSJ. The procedure for VIBSJ is identical to the Sequence VIB with the exception of the items specifically listed in Annex A13. The procedure modifications listed in Annex A13 refer to the corresponding section of the Sequence VIB test method.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1 Exceptions—Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or single source supply equipment specifications. Brake Specific Fuel Consumption is measured in kilograms per kilowatthour. In Figs. A2.4, A2.5, and A2.8, inch-pound units are to be regarded as standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6837 − 10
StandardTest Method for
Measurement of Effects of Automotive Engine Oils on Fuel
Economy of Passenger Cars and Light-Duty Trucks in
1,2
Sequence VIB Spark Ignition Engine
This standard is issued under the fixed designation D6837; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Thetestmethoddescribedinthisstandardcanbeusedbyanyproperlyequippedlaboratory,without
3
outside assistance. However, the ASTM Test Monitoring Center (TMC) provides reference oils and
assessment of the test results obtained on those oils by the laboratory (see AnnexA1). By this means,
the laboratory will know whether their use of the test method gives results statistically similar to those
obtainedbyotherlaboratories.Furthermore,variousagenciesrequirethatalaboratoryutilizetheTMC
services in seeking qualification of oils against specifications. For example, the American Petroleum
Institute (API) imposes such a requirement, in connection with several U.S.Army engine lubricating
oil specifications.
Accordingly, this test method is written for use by laboratories, which utilize the TMC services.
Laboratories that choose not to use those services may simply ignore those portions of the test method
that refer to the TMC.
This test method may be modified by means of Information Letters issued by theTMC. In addition,
the TMC may issue supplementary memoranda related to the test method. Users of this test method
shall contact the TMC, Attention: Administrator, to obtain the most recent of these.
1. Scope procedure for VIBSJ is identical to the Sequence VIB with the
exception of the items specifically listed in Annex A13. The
1.1 This test method covers an engine test procedure for the
procedure modifications listed in Annex A13 refer to the
measurement of the effects of automotive engine oils on the
corresponding section of the Sequence VIB test method.
fuel economy of passenger cars and light-duty trucks with
grossvehicleweightof3856kgorless.Thetestsareconducted
1.3 The values stated in SI units are to be regarded as
on a dynamometer test stand using a specified spark-ignition
standard. No other units of measurement are included in this
engine with a displacement of 4.6-L. It applies to multiviscos-
standard.
ity grade oils used in these applications.
1.3.1 Exceptions—Where there is no direct SI equivalent
suchasscrewthreads,NationalPipeThreads/diameters,tubing
1.2 This test method also provides for the running of an
size, or single source supply equipment specifications. Brake
abbreviated length test that is referred to as the VIBSJ. The
Specific Fuel Consumption is measured in kilograms per
kilowatthour. In Figs. A2.4, A2.5, and A2.8, inch-pound units
1
This test method is under the jurisdiction of ASTM Committee D02 on are to be regarded as standard.
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
1.4 This standard does not purport to address all of the
D02.B0.01 on Passenger Car Engine Oils.
Current edition approved May 1, 2010. Published August 2010. Originally
safety concerns, if any, associated with its use. It is the
approved in 2002. Last previous edition approved in 2009 as D6837–09a. DOI:
responsibility of the user of this standard to establish appro-
10.1520/D6837-10.
priate safety and health practices and determine the applica-
2
The multi-cylinder engine test sequences were originally developed in 1956 by
bility of regulatory limitations prior to use.
anASTMCommitteeD02group.Subsequently,theprocedureswerepublishedinan
ASTM special technical publication. The Sequence VIB was published as Research
1.5 This test method is arranged as follows:
Report RR:D02-1469 dated April 8, 1999.
3
Subject Section
ASTMTestMonitoringCenter,6555PennAvenue,Pittsburgh,PA15206-4489.
Introduction
For other information, refer to Research Report RR:D02-1469, Sequence VIB Test
Scope 1
Development. This research report and this test method are supplemented by
Referenced Documents 2
Information Letters and Memoranda issued by the ASTM TMC. This edition
Terminology 3
incorporates revisions in all Information Letters through No. 09–1.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6837 − 10
Subject Section Subject Section
Summary of Test Method 4 Thermostat Housing 9.3.10
Significance and Use 5 Coolant Inlet 9.3.11
Apparatus 6 Oil Filter Adapter 9.3.12
General 6.1 Dipstick Tube 9.3.13
Test Engine Configuration 6.2 Water Pump 9.3.14
Laboratory Ambient Conditions 6.3
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6837–09a Designation: D6837 – 10
Standard Test Method for
Measurement of Effects of Automotive Engine Oils on Fuel
Economy of Passenger Cars and Light-Duty Trucks in
,
1 2
Sequence VIB Spark Ignition Engine
This standard is issued under the fixed designation D6837; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Thetestmethoddescribedinthisstandardcanbeusedbyanyproperlyequippedlaboratory,without
3
outside assistance. However, the ASTM Test Monitoring Center (TMC) provides reference oils and
assessment of the test results obtained on those oils by the laboratory (seeAnnexA1). By this means,
the laboratory will know whether their use of the test method gives results statistically similar to those
obtainedbyotherlaboratories.Furthermore,variousagenciesrequirethatalaboratoryutilizetheTMC
services in seeking qualification of oils against specifications. For example, the American Petroleum
Institute (API) imposes such a requirement, in connection with several U.S.Army engine lubricating
oil specifications.
Accordingly, this test method is written for use by laboratories, which utilize the TMC services.
Laboratories that choose not to use those services may simply ignore those portions of the test method
that refer to the TMC.
This test method may be modified by means of Information Letters issued by theTMC. In addition,
the TMC may issue supplementary memoranda related to the test method. Users of this test method
shall contact the TMC, Attention: Administrator, to obtain the most recent of these.
1. Scope
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel
economy of passenger cars and light-duty trucks with gross vehicle weight of 3856 kg or less. The tests are conducted on a
dynamometer test stand using a specified spark-ignition engine with a displacement of 4.6-L. It applies to multiviscosity grade oils
used in these applications.
1.2 This test method also provides for the running of an abbreviated length test that is referred to as the VIBSJ. The procedure
for VIBSJ is identical to the Sequence VIB with the exception of the items specifically listed in Annex A13. The procedure
modifications listed in Annex A13 refer to the corresponding section of the Sequence VIB test method.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1 Exceptions—Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size,
or single source supply equipment specifications. Brake Specific Fuel Consumption is measured in kilograms per kilowatthour. In
Figs. A2.4, A2.5, and A2.8, inch-pound units are to be regarded as standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 This test method is arranged as follows:
1
This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.B0.01
on Passenger Car Engine Oils.
Current edition approved Oct.May 1, 2009.2010. Published November 2009.August 2010. Originally approved in 2002. Last previous edition approved in 2009 as
D6837–09a. DOI: 10.1520/D6837-09a.10.1520/D6837-10.
2
The multi-cylinder engine test sequences were originally developed in 1956 by an ASTM Committee D02 group. Subsequently, the procedures were published in an
ASTM special technical publication. The Sequence VIB was published as Research Report RR:D02-1469 dated April 8, 1999.
3
ASTM Test Monitoring Center, 6555 Penn Avenue, Pittsburgh, PA 15206-4489. For other information, refer to Research Report RR:D02-1469, Sequence VIB Test
Development. This research report and this test method are supplemented by Information Letters and Memoranda issued by the ASTM TMC. This edition incorporates
revisions in all Information Letters through No. 08–1.09–1.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 -------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.