iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1558-12

(Guide)

Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation

Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation

SIGNIFICANCE AND USE
4.1 This guide defines the principal elements of information, which are considered important and worth recording and storing permanently in computerized databases. Sufficient information is provided in this guide to enable the user to construct a database structure suitable for the intended application involving thermal insulation.  
4.2 Because of increased activity in building computerized materials databases and the desire to encourage uniformity and ease of data comparison and interchange, these recommended formats provide for the inclusion of specific elements of thermal transmission test data in databases.  
4.3 This guide has no implication on data required for materials production or purchase. Reporting of actual test results shall be as described in the actual materials specification or as agreed upon between the vendor and purchaser.  
4.4 The suggested set of units for the recommended standard format given in this guide is SI. This guide, however, does not preclude other sets of units, such as inch-pound (IP).
SCOPE
1.1 This guide provides recommended formats for the recording of thermal transmission test data for thermal insulation and similar materials for inclusion in computerized material property databases. From this information, the database designer should be able to construct the database dictionary preparatory for development of a database schema.  
1.2 This guide is applicable to thermal transmission test data obtained from standard test methods that cover planar and radial specimen geometries.  
1.3 This guide is not intended for thermal transmission data obtained for thermal insulation assemblies or systems (that is, heat transmission coefficients for walls, roofs, ceilings, and floors).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
31-Aug-2012
ICS
35.240.50 - IT applications in industry
Technical Committee
C16 - Thermal Insulation
Drafting Committee
C16.30 - Thermal Measurement
Current Stage
Ref Project

Relations

Replaces
ASTM C1558-03(2007) - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
Effective Date
01-Sep-2012
Replaced By
ASTM C1558-16 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
Effective Date
01-Mar-2016

Buy Standard

ASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal InsulationASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
PreviousNext
Guide
ASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal InsulationREDLINE ASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
PreviousNext
Guide
REDLINE ASTM C1558-12 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1558 − 12
StandardGuide for
Development of Standard Data Records for Computerization
1
of Thermal Transmission Test Data for Thermal Insulation
This standard is issued under the fixed designation C1558; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C335 Test Method for Steady-State Heat Transfer Properties
of Pipe Insulation
1.1 This guide provides recommended formats for the
C449/C449M Specification for Mineral Fiber Hydraulic-
recording of thermal transmission test data for thermal insula-
Setting Thermal Insulating and Finishing Cement
tion and similar materials for inclusion in computerized mate-
C516 Specification for Vermiculite Loose Fill Thermal In-
rial property databases. From this information, the database
sulation
designer should be able to construct the database dictionary
C518 Test Method for Steady-State Thermal Transmission
preparatory for development of a database schema.
Properties by Means of the Heat Flow Meter Apparatus
1.2 Thisguideisapplicabletothermaltransmissiontestdata
C533 Specification for Calcium Silicate Block and Pipe
obtained from standard test methods that cover planar and
Thermal Insulation
radial specimen geometries.
C534 Specification for Preformed Flexible Elastomeric Cel-
lular Thermal Insulation in Sheet and Tubular Form
1.3 This guide is not intended for thermal transmission data
obtained for thermal insulation assemblies or systems (that is, C547 Specification for Mineral Fiber Pipe Insulation
C549 Specification for Perlite Loose Fill Insulation
heat transmission coefficients for walls, roofs, ceilings, and
floors). C552 Specification for Cellular Glass Thermal Insulation
C553 Specification for Mineral Fiber Blanket Thermal Insu-
1.4 This standard does not purport to address all of the
lation for Commercial and Industrial Applications
safety concerns, if any, associated with its use. It is the
C578 Specification for Rigid, Cellular Polystyrene Thermal
responsibility of the user of this standard to establish appro-
Insulation
priate safety and health practices and determine the applica-
C592 Specification for Mineral Fiber Blanket Insulation and
bility of regulatory requirements prior to use.
Blanket-Type Pipe Insulation (Metal-Mesh Covered) (In-
dustrial Type)
2. Referenced Documents
C610 Specification for Molded Expanded Perlite Block and
2
2.1 ASTM Standards:
Pipe Thermal Insulation
C168 Terminology Relating to Thermal Insulation
C612 Specification for Mineral Fiber Block and Board
C177 Test Method for Steady-State Heat Flux Measure-
Thermal Insulation
ments and Thermal Transmission Properties by Means of
C656 Specification for Structural Insulating Board, Calcium
the Guarded-Hot-Plate Apparatus
Silicate
C195 Specification for Mineral Fiber Thermal Insulating
C665 Specification for Mineral-Fiber Blanket Thermal Insu-
Cement
lation for Light Frame Construction and Manufactured
C196 Specification for Expanded or Exfoliated Vermiculite
Housing
Thermal Insulating Cement
C726 Specification for Mineral Wool Roof Insulation Board
C208 Specification for Cellulosic Fiber Insulating Board
C728 Specification for Perlite Thermal Insulation Board
C739 Specification for Cellulosic Fiber Loose-Fill Thermal
Insulation
1
This guide is under the jurisdiction of ASTM Committee C16 on Thermal
C745 Test Method for Heat Flux Through Evacuated Insu-
Insulation and is the direct responsibility of Subcommittee C16.30 on Thermal
lations Using a Guarded Flat Plate Boiloff Calorimeter
Measurement.
3
(Withdrawn 2008)
Current edition approved Sept. 1, 2012. Published October 2012. Originally
approvedin2003.Lastpreviouseditionapprovedin2007asC1558–03(2007).DOI: C764 Specification for Mineral Fiber Loose-Fill Thermal
10.1520/C1558-12.
Insulation
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1558 − 12
4
C991 Specification for Flexible Fibrous Glass Insulation for Guarded Hot Plate Apparatus
Metal Buildings ISO 8497 Thermal Insulation—Determination of Steady-
C1014 Specification for Spray-Applied Mineral Fiber Ther- State Thermal Transmission Properties of Thermal Insu-
4
mal and Sound Absorbing Insulation lation for Circular Pipes
C
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1558 − 03 (Reapproved 2007) C1558 − 12
Standard Guide for
Development of Standard Data Records for Computerization
1
of Thermal Transmission Test Data for Thermal Insulation
This standard is issued under the fixed designation C1558; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide provides recommended formats for the recording of thermal transmission test data for thermal insulation and
similar materials for inclusion in computerized material property databases. From this information, the database designer should
be able to construct the database dictionary preparatory for development of a database schema.
1.2 This guide is applicable to thermal transmission test data obtained from standard test methods that cover planar and radial
specimen geometries.
1.3 This guide is not intended for thermal transmission data obtained for thermal insulation assemblies or systems (that is, heat
transmission coefficients for walls, roofs, ceilings, and floors).
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
requirements prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C195 Specification for Mineral Fiber Thermal Insulating Cement
C196 Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
C208 Specification for Cellulosic Fiber Insulating Board
C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C449/C449M Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
C516 Specification for Vermiculite Loose Fill Thermal Insulation
C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C533 Specification for Calcium Silicate Block and Pipe Thermal Insulation
C534 Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form
C547 Specification for Mineral Fiber Pipe Insulation
C549 Specification for Perlite Loose Fill Insulation
C552 Specification for Cellular Glass Thermal Insulation
C553 Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications
C578 Specification for Rigid, Cellular Polystyrene Thermal Insulation
C592 Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial
Type)
C610 Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation
C612 Specification for Mineral Fiber Block and Board Thermal Insulation
C656 Specification for Structural Insulating Board, Calcium Silicate
C665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
1
This guide is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.30 on Thermal Measurement.
Current edition approved Sept. 1, 2007Sept. 1, 2012. Published September 2007October 2012. Originally approved in 2003. Last previous edition approved in 20032007
as C1558C1558–03(2007).–03. DOI: 10.1520/C1558-03R07.10.1520/C1558-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1558 − 12
C726 Specification for Mineral Wool Roof Insulation Board
C728 Specification for Perlite Thermal Insulation Board
C739 Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
C745 Test Method for Heat Flux Through Evacuated Insulations Using a Guarded Flat Plate Boiloff Calorimeter (Withdrawn
3
2008)
C764 Specification for Mineral Fiber Loose-Fill Thermal Insulation
C991 Specification for Flexible Fibrous Glass Insulation f
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1558-19(Guide)
Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation

SIGNIFICANCE AND USE
4.1 This guide defines the principal elements of information, which are considered important and worth recording and storing permanently in computerized databases. Sufficient information is provided in this guide to enable the user to construct a database structure suitable for the intended application involving thermal insulation. Guidance on the storage of (optional) digital images associated with test data is provided in Appendix X1.  
4.2 Because of increased activity in building computerized materials databases and to maintain uniformity and ease of data comparison and interchange, these formats provide for the inclusion of specific elements of thermal transmission test data in databases.  
4.3 This guide has no implication on data required for materials production or purchase. Reporting of actual test results shall be as described in the actual materials specification or as agreed upon between the vendor and purchaser.  
4.4 The suggested set of units for the recommended standard format given in this guide is SI. This guide, however, does not preclude other sets of units, such as inch-pound (IP).
SCOPE
1.1 This guide provides recommended formats for the recording of thermal transmission test data for thermal insulation and similar materials for inclusion in computerized material property databases. From this information, the database designer is able to construct the database dictionary preparatory for development of a database schema.  
1.2 This guide is applicable to thermal transmission test data obtained from standard test methods that cover planar and radial specimen geometries.  
1.3 This guide is not intended for thermal transmission data obtained for thermal insulation assemblies or systems (that is, heat transmission coefficients for walls, roofs, ceilings, and floors).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    11 pages
    English language
    sale 15% off
  • Guide
    11 pages
    English language
    sale 15% off
ASTM
ASTM F3605-23(Guide)
Standard Guide for Additive Manufacturing of Metals — Data — File Structure for In-Process Monitoring of Powder Bed Fusion (PBF)

SIGNIFICANCE AND USE
5.1 The converted file will be organized in a specific structure to reflect the relationship between the in-process monitoring data with the quality of the printing process.  
5.2 This standard file structure will help ensure the data compatibility across various printing systems, analyses, and illustration software. It aims to be self-explaining and easy to use to accommodate data sharing in a large base of users.  
5.3 The converted file can be used for the evaluation of printing quality and the detections of defects and anomalies.
SCOPE
1.1 This guide provides standardized procedures and requirements for converting acquired in-process monitoring data into one file representing the printing process of powder bed fusion (PBF) for quality evaluation.  
1.2 Many of the operational descriptions included in this guide are intended as general overviews. They may not present the detailed information required.  
1.3 This guide covers:  
1.3.1 Data registration,  
1.3.2 Extraction of in-process data, and  
1.3.3 File conversion and visualization.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3560-22(Specification)
Standard Specification for Additive Manufacturing – Data – Common Exchange Format for Particle Size Analysis by Light Scattering

SCOPE
1.1 This specification has been developed to facilitate exchanging and analyzing particle size distribution (PSD) by light scattering data from databases, data management systems, point of origin, or other data sources that may use different data dictionaries, schemas, or formats.  
1.2 This specification prescribes the use of a common exchange format in such a way that PSD data defined through proprietary means can be easily exchanged for process understanding and qualification.  
1.3 This specification facilitates the interoperability of PSD data by identifying the data elements defined in standardized terminology, as well as defining those salient terms with indisputable meanings. In doing so, this specification extends the common AM data dictionary defined in Practice F3490 to encapsulate PSD process-specific data elements. Generic data elements and relationships present in that standard are inherited and applied in this practice where relevant.  
1.4 This specification specifies names that serve to uniquely identify the PSD data elements. The data type, value domain, and term definition for each data element are also specified in this practice. References are provided for those data elements with established definitions or reporting guidelines in existing standards.  
1.5 This specification prescribes a file format and structure for the exchange of PSD data. This format defines a method for sharing data via the defined PSD data elements herein and provides a basis for validation of data exchanged using this format.  
1.6 This specification recommends levels of data sharing that vary from minimal to robust. It prescribes best practices for checking conformance based on the common data exchange format.  
1.7 This specification does not specify:  
1.7.1 An exhaustive set of data items that could be exchanged related to PSD by light scattering.  
1.7.2 A definition of a minimum viable data set for PSD by light scattering.  
1.7.3 Data items or an exchange format for PSD methods other than light scattering, for example, imaging or sieving.  
1.7.4 Data elements for data modules related to PSD (for example, for personnel, material, or equipment).  
1.7.5 The implementation details of how data should be imported to proprietary data management systems from the common data exchange format.  
1.7.6 The implementation details of how data should be exported from proprietary data management systems to the common data exchange format.  
1.7.7 Guidelines for creating unique identifiers for data module records  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM F3243-21(Practice)
Standard Practice for Implementing Communications Impairments on A-UGV Systems

SIGNIFICANCE AND USE
4.1 A-UGVs operate in a wide range of indoor and outdoor applications that include many communications challenges that can affect A-UGV control and monitoring. An A-UGV system or A-UGVS as defined in Terminology F3200 includes the A-UGV and all associated components, equipment, software, and communications necessary to make a fully functional system. Communications impairments can cause: (1) changes in A-UGV operation, (2) changes in behavior in system components such as control and scheduling, or (3) changes in operation or timing of infrastructure equipment coordination. This practice is intended to record the task performance of an A-UGV while communications are impaired in a specified and repeatable manner (for example, standard test method).  
4.2 Communications impairments can occur at a variety of locations within the A-UGVS. The network topology in Fig. 1 shows many of the common communications links that could be impaired. The numbered arrows in Fig. 1 label different places where communications impairments could occur. The box colors (that is, green, red, blue) indicate different types of impairments where the two red boxes are similar to each other. Fig. 1 will be used throughout this practice and included on the test report for use in describing the test setup and results by the test supervisor.  
FIG. 1 Block Diagram of Communications for Control/Monitoring of A-UGVs and Associated Facility Equipment in which Numbers with Arrows Indicate Examples of Communications Impairment Locations  
4.3 The requested expected results provide pass/fail reporting criteria along with recorded notes pertinent to the test or results or both. It is possible that the communications impairments used will have no noticeable effect, and this is often the desired outcome.
SCOPE
1.1 This practice considers impairments of communications within an automatic, automated, or autonomous unmanned ground vehicle (A­UGV) system during task execution. An A-UGV system typically uses communications between an A-UGV and fixed system components and resources, such as off-board control, job and fleet scheduling, infrastructure equipment interactions, or cloud-computing programs for tasks. Communications impairments can cause an A-UGV operation to change in various ways that can include delays or failure to complete the task.  
1.2 This practice is designed for applying known communications impairments to an A-UGV system in conjunction with A-UGV task testing. It is designed to create similar changes in communications that can possibly cause task performance limiting effects that are often experienced by an A-UGV system in different environments.  
1.3 This practice is intended to simulate impairments that may be present during the operation of an A-UGV system. This practice can be used, for example, by a manufacturer to indicate that system performance was tested to be robust against specific test communications impairments. The tests are not intended to test situations that should be eliminated during system installation, for example, a duplicate internet protocol (IP) address on the network.  
1.4 This practice only describes communications impairments. It does not specify an A-UGV task. The A-UGV task should be a defined ASTM International test method or task description in similar detail.  
1.5 This practice defines methods to record communications impairment types and extents while the A-UGV is stationary or performs a task. Temporal or spatial extents in which communications impairments occur include the timing, duration, location within the task, or other triggered events. Examples for implementing common communications impairments are provided.  
1.6 This practice is not intended for:  
1.6.1 Communications impairments between onboard components of an A-UGV, for example, onboard sensors-to-onboard computers.  
1.6.2 Communications or measurement impairments directly affecting external reference or p...

  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM F3499-21(Test Method)
Standard Test Method for Confirming the Docking Performance of A-UGVs

SIGNIFICANCE AND USE
7.1 A-UGVs operate in a wide range of applications such as manufacturing facilities and warehouses. The testing results of the candidate A-UGV shall describe, in a statistically significant way, the ability of the A-UGV to position itself at a fixed location or relative to a dock. This test method defines tests for use by manufacturers and users of A-UGVs to measure and record the docking performance. The test applies to different types of A-UGV, applications and test apparatus.  
7.2 Navigation—The test applies to all types of navigation. The capabilities of the A-UGV to apply its navigation method to a given environment will be objectively determined by its performance in the test.  
7.3 Vehicle—The test results of the candidate A-UGV will confirm, in a statistically significant way, how reliably an A-UGV arrives at a dock from one or more start locations. Refer to Test Method F3244 for typical vehicle configurations.  
7.4 Apparatus—The test method is scalable, using similar apparatus to interface to different A-UGVs.  
7.5 Defining a Successful Test—The probability that a repetition will be successful (R) and the confidence (C) in that probability are used to identify how many sequential successful repetitions are required to pass a test. The test requestor shall define these values and record them on the test report (see Appendix X1 Table X1.1).
SCOPE
1.1 This test method defines standard tests that demonstrate and confirm positioning of an A-UGV. Positioning, the repeatability of A-UGV location when stationary after completing maneuvers to a stop location, may be defined globally or locally relative to local infrastructure. The latter has become known as docking. See Terminology F3200-18a for terminology definitions. The test also includes a method to confirm the repeatability of height control of load transfer equipment, for example an A-UGV with fork tines.  
1.2 This test method is intended for use by A-UGV manufacturers, installers, and users to quantitatively confirm the maneuverability and repeatability of an A-UGV’s positioning or docking. Positioning and docking are similar operations and the tests described are applicable to either. The term docking will be used throughout this test method to include both global positioning and local docking. The tests facilitate comparative trials across a set of A-UGVs or multiple trials over a period of time.  
1.3 The tests can be carried out by many vehicles using different methods of location measurement and control to achieve the demanded performance. Vehicle configurations and vehicle components include:  
1.3.1 Vehicle load type (for example, fork lift, roller deck, trailer, flat deck);  
1.3.2 Vehicle drive mechanics (for example, steered tricycle, two-wheel differential, steered omni-directional or ‘mecanum wheel’ drives);  
1.3.3 Navigation sensors (for example, scanning laser, local beacons, floor marking, environmental features);  
1.3.4 Docking sensors (sensors, for example, camera, line detector, and laser scanner, which are used primarily for local measurement at the dock).  
1.4 The A-UGV may include roller tables, fork tines, robot arm(s) or other mechanisms to transfer the load or interact with the dock (for example, perform assembly). The standard test can be applied to A-UGVs with any of these load transfer mechanisms. The repeatability along each measured axis is measured and compared to a defined repeatability margin. The set of repeatability margins comprises the complete task performance margin (TPM).  
1.5 This test method shall be performed in a testing laboratory or the location where the specified apparatus and environmental conditions are implemented. Environmental conditions shall be recorded as specified in Practice F3218-17.  
1.6 Standard test apparatus is specified to be easily fabricated, facilitating self-evaluation by A-UGV developers and users, and providing practice for A-UGV developers, u...

  • Standard
    25 pages
    English language
    sale 15% off
ASTM
ASTM G107-95(2020)e1(Guide)
Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input

SIGNIFICANCE AND USE
4.1 The guide is intended to facilitate the recording of corrosion test results and does not imply or endorse any particular database design or schema. It provides a useful reference to be consulted before initiating a corrosion test to be sure plans are made to record all relevant data.  
4.2 Corrosion tests are usually performed following a prescribed test procedure that is often not a standard test method. Most corrosion tests involve concurrent exposure of multiple specimens of one or more materials (refer to 6.1.1).  
4.3 This guide is designed to record data for individual specimens with groupings by separate tests (as contrasted to separate test methods) as described in 4.2 and 6.1.1. Consequently, some of the individual fields may apply to all of the specimens in a single test, while others must be repeated as often as necessary to record data for individual specimens.  
4.4 The guidelines provided are designed for recording data for entry into computerized material performance databases. They may be useful for other applications where systematic recording of corrosion data is desired.  
4.5 Reliable comparisons of corrosion data from multiple sources will be expedited if data are provided for as many of the listed fields as possible. Comparisons are possible where data are limited, but some degree of uncertainty will be present.  
4.6 Certain specialized corrosion tests may require additional data elements to fully characterize the data recorded. This guide does not preclude these additions. Other ASTM guides for recording data from mechanical property tests may be helpful.  
4.7 This guide does not cover the recording of data from electrochemical corrosion tests.  
4.8 These material identification guidelines are compatible with Guide E1338.
SCOPE
1.1 This guide covers the data categories and specific data elements (fields) considered necessary to accommodate desired search strategies and reliable data comparisons in computerized corrosion databases. The data entries are designed to accommodate data relative to the basic forms of corrosion and to serve as guides for structuring multiple source database compilations capable of assessing compatibility of metals and alloys for a wide range of environments and exposure conditions.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM ISO/ASTM52915-20(Specification)
Specification for additive manufacturing file format (AMF) Version 1.2

ABSTRACT
This specification provides a framework for an interchange format to address the current and future needs of the additive manufacturing technology. The additive manufacturing file (AMF) may be prepared, displayed, and transmitted on paper or electronically, provided the requirements presented in this specification are met. When prepared in a structured electronic format, strict adherence to an extensible markup language (XML) schema is required to support standards-compliant interoperability.
SCOPE
1.1 This document provides the specification for the Additive Manufacturing File Format (AMF), an interchange format to address the current and future needs of additive manufacturing technology.  
1.2 This document specifies the requirements for the preparation, display and transmission for the AMF. When prepared in a structured electronic format, strict adherence to an extensible markup language (XML)(1)2 schema supports standards-compliant interoperability.
Note 1: A W3C XML schema definition (XSD) for the AMF is available from ISO from http://standards.iso.org/iso/52915 and from ASTM from www.astm.org/MEETINGS/images/amf.xsd. An implementation guide for such an XML schema is provided in Annex A1.  
1.3 It is recognized that there is additional information relevant to the final part that is not covered by the current version of this document. Suggested future features are listed in Annex A2.  
1.4 This document does not specify any explicit mechanisms for ensuring data integrity, electronic signatures and encryptions.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM E1018-20e1(Guide)
Standard Guide for Application of ASTM Evaluated Cross Section Data File

SIGNIFICANCE AND USE
4.1 The ENDF/B library in the United States and similar libraries elsewhere, such as JEFF (23), JENDL (21), and BROND (22), provide a compilation of neutron cross section and other nuclear data for use by the nuclear community. The availability of these excellent evaluations makes possible standardized usage, thereby allowing easy referencing and intercomparisons of calculations. However, as the first ENDF/B files were developed it became apparent that they were not adequate for all applications. This need resulted in the development of the specialized ENDF/B Dosimetry File (17, 25), consisting of activation cross sections important for dosimetry applications. This file was made available worldwide. Later, other “Special Purpose” files were introduced (26). In the ENDF/B-VI compilation (27), dosimetry files no longer appeared as separate evaluation files. The ENDF/B-VII.0 compilation (28) removed most of the reaction-specific covariance files used by the dosimetry community. It kept the covariance files for the “standard cross sections” in a special sub-library, but the covariance data in this sub-library are only provided over the energy range in which each reaction is considered to be a “standard”, and does not include the full energy range required for LWR PVS dosimetry applications. Later updates to the ENDF/B releases added covariance files for some reaction channels but these covariance files were often based solely on calculations and were not representative of the methodology used to derive the underlying ENDF/B cross section. In response to the need for a dosimetry-specific library, the International Atomic Energy Agency convened a Coordinated Research Project (CRP) that drew upon the set of international experts to provide a recommended set of dosimetry cross sections and to compile a set of validation evidence that supported the use of this recommended dataset. This file, the International Reactor Dosimetry and Fusion File (IRDFF) (19, 20), draws upon oth...
SCOPE
1.1 This guide covers the establishment and use of an ASTM evaluated nuclear data cross section and uncertainty file for analysis of single or multiple sensor measurements in neutron fields related to light water reactor LWR-Pressure Vessel Surveillance (PVS). These fields include in- and ex-vessel surveillance positions in operating power reactors, benchmark fields, and reactor test regions.  
1.2 Requirements for establishment of ASTM-recommended cross section files address data format, evaluation requirements, validation in benchmark fields, evaluation of error estimates (covariance file), and documentation. A further requirement for components of the ASTM-recommended cross section file is their internal consistency when combined with sensor measurements and used to determine a neutron spectrum.  
1.3 Specifications for use include energy region of applicability, data processing requirements, and application of uncertainties.  
1.4 This guide is directly related to and should be used primarily in conjunction with Guides E482 and E944, and Practices E560, E185, and E693.  
1.5 The ASTM cross section and uncertainty file represents a generally available data set for use in sensor set analysis. However, the availability of this data set does not preclude the use of other validated data, either proprietary or nonproprietary. When alternate cross section files that deviate from the requirements laid out in this standard are used, the deviations should be noted to the customer of the dosimetry application.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standar...

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM ISO/ASTM52921-13(2019)(Terminology)
Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

SIGNIFICANCE AND USE
3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CNC are not sufficient to be applicable across the full spectrum of additive manufacturing equipment. This terminology expands upon the principles of ISO 841 and applies them specifically to additive manufacturing. Although this terminology is intended to complement ISO 841, if there should arise any conflict, this terminology shall have priority for additive manufacturing applications. For any issues not covered in this terminology, the principles in ISO 841 may be applied.  
3.2 Furthermore, this terminology does not prescribe the use of any specific existing testing methodologies or standards that practitioners of AM may wish to employ for testing purposes; however, it is expected that practitioners will employ appropriate existing methodologies and standards to test parts made by AM.
SCOPE
1.1 This terminology includes terms, definitions of terms, descriptions of terms, nomenclature, and acronyms associated with coordinate systems and testing methodologies for additive manufacturing (AM) technologies in an effort to standardize terminology used by AM users, producers, researchers, educators, press/media, and others, particularly when reporting results from testing of parts made on AM systems. Terms included cover definitions for machines/systems and their coordinate systems plus the location and orientation of parts. It is intended, where possible, to be compliant with ISO 841 and to clarify the specific adaptation of those principles to additive manufacturing.
Note 1: The applicability of this standard to cladding has to be evaluated. Discussions are under progress.
Note 2: Non-cartesian systems are not covered by this standard.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM C1558-19(Guide)
Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation

SIGNIFICANCE AND USE
4.1 This guide defines the principal elements of information, which are considered important and worth recording and storing permanently in computerized databases. Sufficient information is provided in this guide to enable the user to construct a database structure suitable for the intended application involving thermal insulation. Guidance on the storage of (optional) digital images associated with test data is provided in Appendix X1.  
4.2 Because of increased activity in building computerized materials databases and to maintain uniformity and ease of data comparison and interchange, these formats provide for the inclusion of specific elements of thermal transmission test data in databases.  
4.3 This guide has no implication on data required for materials production or purchase. Reporting of actual test results shall be as described in the actual materials specification or as agreed upon between the vendor and purchaser.  
4.4 The suggested set of units for the recommended standard format given in this guide is SI. This guide, however, does not preclude other sets of units, such as inch-pound (IP).
SCOPE
1.1 This guide provides recommended formats for the recording of thermal transmission test data for thermal insulation and similar materials for inclusion in computerized material property databases. From this information, the database designer is able to construct the database dictionary preparatory for development of a database schema.  
1.2 This guide is applicable to thermal transmission test data obtained from standard test methods that cover planar and radial specimen geometries.  
1.3 This guide is not intended for thermal transmission data obtained for thermal insulation assemblies or systems (that is, heat transmission coefficients for walls, roofs, ceilings, and floors).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    11 pages
    English language
    sale 15% off
  • Guide
    11 pages
    English language
    sale 15% off