iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1401-07

(Guide)

Standard Guide for Structural Sealant Glazing

Standard Guide for Structural Sealant Glazing

SCOPE
1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system.
1.2 This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not more than 15° from vertical; however, limited information is included concerning a sloped SSG application.
1.3 Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is acceptable for a SSG system application.
1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations.
1.5 The calculations and values stated in SI units are to be regarded as the standard. Values in parenthesis and inch-pound units are for information only. SI units in this guide are in conformance with IEEE/ASTM SI 10.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Oct-2007
ICS
91.100.50 - Binders. Sealing materials
Technical Committee
C24 - Building Seals and Sealants
Drafting Committee
C24.10 - Specifications, Guides and Practices
Current Stage
Ref Project

Relations

Replaces
ASTM C1401-02 - Standard Guide for Structural Sealant Glazing
Effective Date
01-Nov-2007
Replaced By
ASTM C1401-09 - Standard Guide for Structural Sealant Glazing
Effective Date
15-Apr-2009
Referred By
ASTM C1472-16(2022) - Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
Effective Date
01-Nov-2007
Referred By
ASTM C1487-19 - Standard Guide for Remedying Structural Silicone Glazing
Effective Date
01-Nov-2007
Referred By
ASTM C1394-20 - Standard Guide for In-Situ Structural Silicone Glazing Evaluation
Effective Date
01-Nov-2007
Referred By
ASTM C1193-16(2023) - Standard Guide for Use of Joint Sealants
Effective Date
01-Nov-2007
Referred By
ASTM C1564-20 - Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
Effective Date
01-Nov-2007
Referred By
ASTM C1184-23 - Standard Specification for Structural Silicone Sealants
Effective Date
01-Nov-2007

Buy Standard

ASTM C1401-07 - Standard Guide for Structural Sealant GlazingASTM C1401-07 - Standard Guide for Structural Sealant Glazing
PreviousNext
Guide
ASTM C1401-07 - Standard Guide for Structural Sealant Glazing
English language
55 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM C1401-07 - Standard Guide for Structural Sealant GlazingREDLINE ASTM C1401-07 - Standard Guide for Structural Sealant Glazing
PreviousNext
Guide
REDLINE ASTM C1401-07 - Standard Guide for Structural Sealant Glazing
English language
55 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1401 – 07
Standard Guide for
1
Structural Sealant Glazing
This standard is issued under the fixed designation C 1401; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C119 Terminology Relating to Dimension Stone
C 162 Terminology of Glass and Glass Products
1.1 Structural sealant glazing, hereinafter referred to as
C 503 Specification for Marble Dimension Stone
SSG, is an application where a sealant not only can function as
C 509 Specification for Elastomeric Cellular Preformed
abarrieragainstthepassageofairandwaterthroughabuilding
Gasket and Sealing Material
envelope, but also primarily provides structural support and
C 510 Test Method for Staining and Color Change of
attachment of glazing or other components to a window,
Single- or Multicomponent Joint Sealants
curtain wall, or other framing system.
C 568 Specification for Limestone Dimension Stone
1.2 This guide provides information useful to design pro-
C 615 Specification for Granite Dimension Stone
fessionals, manufacturers, contractors, and others for the de-
C 717 Terminology of Building Seals and Sealants
sign and installation of a SSG system. This information is
C 719 Test Method for Adhesion and Cohesion of Elasto-
applicableonlytothisglazingmethodwhenusedforabuilding
meric Joint Sealants Under Cyclic Movement (Hockman
wall that is not more than 15° from vertical; however, limited
Cycle)
information is included concerning a sloped SSG application.
C 794 Test Method for Adhesion-in-Peel of Elastomeric
1.3 Only a silicone chemically curing sealant specifically
Joint Sealants
formulated, tested, and marketed for structural sealant glazing
C 864 Specification for Dense Elastomeric Compression
is acceptable for a SSG system application.
Seal Gaskets, Setting Blocks, and Spacers
1.4 The committee with jurisdiction for this standard is not
C 880 Test Method for Flexural Strength of Dimension
aware of any comparable standard published by other organi-
Stone
zations.
C 920 Specification for Elastomeric Joint Sealants
1.5 The calculations and values stated in SI units are to be
C 1036 Specification for Flat Glass
regarded as the standard. Values in parenthesis and inch-pound
C 1048 Specification for Heat-Treated Flat Glass—Kind
units are for information only. SI units in this guide are in
HS, Kind FT Coated and Uncoated Glass
conformance with IEEE/ASTM SI 10.
C 1087 Test Method for Determining Compatibility of
1.6 This standard does not purport to address all of the
Liquid-Applied Sealants with Accessories Used in Struc-
safety concerns, if any, associated with its use. It is the
tural Glazing Systems
responsibility of the user of this standard to establish appro-
C 1115 Specification for Dense Elastomeric Silicone Rub-
priate safety and health practices and determine the applica-
ber Gaskets and Accessories
bility of regulatory limitations prior to use.
C 1135 Test Method for Determining Tensile Adhesion
2. Referenced Documents
Properties of Structural Sealants
2
C 1172 SpecificationforLaminatedArchitecturalFlatGlass
2.1 ASTM Standards:
C 1184 Specification for Structural Silicone Sealants
B117 Practice for Operating Salt Spray (Fog) Apparatus
C 1193 Guide for Use of Joint Sealants
C99 Test Method for Modulus of Rupture of Dimension
C 1201 Test Method for Structural Performance of Exterior
Stone
Dimension Stone Cladding Systems by Uniform StaticAir
Pressure Difference
1
ThisguideisunderthejurisdictionofASTMCommitteeC24onBuildingSeals
C 1248 Test Method for Staining of Porous Substrate by
and Sealants and is the direct responsibility of Subcommittee C24.10 on Specifi-
Joint Sealants
cations, Guides and Practices.
C 1249 Guide for Secondary Seal for Sealed Insulating
Current edition approved Nov. 1, 2007. Published November 2007. Originally
approved in 1998. Last previous edition approved in 2002 as C 1401–02.
Glass Units for Structural Sealant Glazing Applications
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1401–07
C 1253 Test Method for Determining the Outgassing Poten- E 1886 Test Method for Performance of Exterior Windows,
tial of Sealant Backing Curtain Walls, Doors, and Impact Protective Systems
Impacted by Missile(s) and Exposed to Cyclic Pressure
C 1265 Test
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1401–02 Designation: C 1401 – 07
Standard Guide for
1
Structural Sealant Glazing
This standard is issued under the fixed designation C 1401; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier
against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of
glazing or other components to a window, curtain wall, or other framing system.
1.2 This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and
installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not
more than 15° from vertical; however, limited information is included concerning a sloped SSG application.
1.3 Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is
acceptable for a SSG system application.
1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations.
1.5 The calculations and values stated in SI units are to be regarded as the standard. Values in parenthesis and inch-pound units
are for information only. SI units in this guide are in conformance with IEEE/ASTM SI 10.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B117 B 117 Practice for Operating Salt Spray (Fog) Apparatus
C 99 Test Method for Modulus of Rupture of Dimension Stone
C 119 Terminology Relating to Dimension Stone
C 162 Terminology of Glass and Glass Products
2
C 503 Specification for Marble Dimension Stone (Exterior)
C 509 Specification for Elastomeric Cellular Preformed Gasket and Sealing Material
C 510 Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
C 568 Specification for Limestone Dimension Stone
C 615 Specification for Granite Dimension Stone
C 717 Terminology of Building Seals and Sealants
C 719 Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
C 794 Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
C 864 Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers
C 880 Test Method for Flexural Strength of DimensionalDimension Stone
C 920 Specification for Elastomeric Joint Sealants
C 1036 Specification for Flat Glass
C 1048 Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass
C 1087 Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing
Systems
C 1115 Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
C 1135 Test Method for Determining Tensile- Adhesion Properties of Structural Sealants
1
This guide is under the jurisdiction of ASTM Committee C24 on Sealants and is the direct responsibility of Subcommittee C24.35 on Structural Sealants.
Current edition approved May 10, 2002. Published July 2002. Originally published as C1401–98. Last previous edition C1401–98.
1
This guide is under the jurisdiction ofASTM Committee C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.10 on Specifications,
Guides and Practices.
Current edition approved Nov. 1, 2007. Published November 2007. Originally approved in 1998. Last previous edition approved in 2002 as C 1401–02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
, Vol 04.07.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1401–07
C 1172 Specification for Laminated Architectural Flat Glass
C 1184 Specification f
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1737-23(Guide)
Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing

SIGNIFICANCE AND USE
5.1 This guide is not intended to measure the precise temperature range for dispensing and curing product under all the possible substrate and environmental factors but to provide a basis for benchmarking a foam sealant product under specific laboratory conditions.  
5.2 The product user is encouraged to evaluate each application and determine suitability for actual use.
SCOPE
1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures.  
1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions.  
1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures.  
1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1257-15(2023)(Test Method)
Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants

SIGNIFICANCE AND USE
5.1 It is difficult to establish a precise correlation between laboratory accelerated and natural weathering because of  (1) geographical climatic variations, local weather variation from normal, and local pollutants and (2) the fact that the acceleration factor is material dependent, varying with the type of material as well as its formulation. This test method is used to determine the resistance of a sealant to laboratory accelerated weathering and, if a control material with known outdoor weathering performance is used, the relative weathering performance of the sealant against that of the control material.  
5.2 This test method is conducted using aluminum channels. Other substrate materials may show different results.
SCOPE
1.1 This test method includes two laboratory accelerated exposure procedures for predicting the effects of ultraviolet or ultraviolet/visible radiation, heat, and moisture on color, chalking, cracking, and adhesion of solvent-release sealants.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2202-00(2023)(Test Method)
Standard Test Method for Slump of Sealants

SIGNIFICANCE AND USE
4.1 Excessive sealant slump or sag in a vertical joint may cause improper bead shape or inadequate sealant thickness in the completed joint. Slump measurements, as described in this test method, serve to evaluate only this application characteristic; they do not predict the performance capability of the sealant after installation.
SCOPE
1.1 This test method covers a laboratory procedure for the determination of the degree of slump of a sealant when used in a vertical joint in a structure.  
1.2 The values stated in either inch-pound or SI (metric) units are to be separately regarded as the standard. Within the text, the inch-pound units are shown in parentheses.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: A related ISO standard is ISO 7390. The user should compare to determine how it differs from this test method.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1401-23(Guide)
Standard Guide for Structural Sealant Glazing

SIGNIFICANCE AND USE
5.1 The old saying “A chain is only as strong as its weakest link” is very applicable to a SSG system. In reality, a SSG system, to be successful, must establish and maintain a chain of adhesion. For example, a factory applied finish must adhere adequately to a metal framing member, a structural glazing sealant to that metal finish, that structural glazing sealant to a reflective coating on a glass lite, and lastly, that reflective coating to a glass surface. This guide will assist in the identification and development of, among others, performance criteria, test methods, and industry practices that should be implemented to obtain the required structural glazing sealant adhesion and compatibility with other system components.  
5.2 Although this guide has been arranged to permit easy access to specific areas of interest, it is highly recommended that the entire guide is read and understood before establishing the requirements for a particular SSG system.  
5.3 This guide should not be the only criteria upon which the design and installation of a SSG system is based. The information herein is provided to assist in the development of a specific program with a goal of achieving a successful SSG system installation. Information and guidelines are provided for the evaluation, design, installation, and maintenance of a SSG system and many of its various components. Considering the range of properties of structural glazing silicone sealants, as well as the many types of framing system designs, material combinations that can be used, various material finishes, and the many types and varieties of accessories, the information contained herein is general in nature.  
5.4 Generally, the design, fabrication, and installation of a SSG system requires more technical knowledge and experience then is required for a conventionally glazed window or curtain wall system. To ensure the success of a SSG system, it is important that suppliers, fabricators, and installers of materials an...
SCOPE
1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system.  
1.2 This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not more than 15° from vertical; however, limited information is included concerning a sloped SSG application.  
1.3 Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is acceptable for a SSG system application.  
1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. SI units in this guide are in conformance with IEEE/ASTM SI 10.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    56 pages
    English language
    sale 15% off
  • Guide
    56 pages
    English language
    sale 15% off
ASTM
ASTM C792-23(Test Method)
Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants

SIGNIFICANCE AND USE
5.1 Weight loss through volatilization of components of a sealant in a building joint may affect sealant appearance because of shrinkage, and sealant performance because of the loss of functional sealant components. Exposure to high-temperature environments will accelerate the loss of volatiles.  
5.2 This test method measures weight loss. It can be used in combination with a knowledge of sealant density to estimate shrinkage. In addition, when compared to sealant theoretical weight solids, it provides an estimate of the extent to which functional sealant components can be volatilized when exposed to high service temperatures. Substantial losses of this type may help predict early failures in durability. Also, development of cracks or chalking, or both, lessens sealant service life. However, a sealant that develops no cracks or chalking, or low weight loss in this test method, does not necessarily assure good durability.
SCOPE
1.1 This test method covers a laboratory procedure for determining the effects of heat aging on weight loss, cracking, and chalking of cured-in-place elastomeric joint sealants (single- and multi-component) for use in building construction.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 There is no known ISO equivalent to this test method.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1330-23(Specification)
Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants

ABSTRACT
This standard specification covers the basic requirements for cylindrical sealant backing for use with cold liquid-applied sealants. Cylindrical sealant backings are classified into three types: type C, type O, and type B, composed predominantly of closed cell material, open cell material, and bi-cellular material, respectively. Test methods for cylindrical sealant backing include water absorption, density, outgassing, compression deflection and recovery, and tensile strength. The sealant shall be clean, free of scale, foreign matter, oil, or water.
SIGNIFICANCE AND USE
5.1 This specification is designed to give some indication as to the differences in performance for various cylindrical sealant backings.  
5.2 Although this specification qualifies a cylindrical sealant backing for use, it does not address the compatibility of the backing with the sealants with which it will make contact. Sealant compatibility should be confirmed by the sealant manufacturer. Compatibility characteristics of sealants in contact with cylindrical sealant backings can be determined by Test Method C1087.
SCOPE
1.1 This specification covers the basic requirements for cylindrical sealant backing to be used with cold liquid applied sealants for use in building seals.  
1.2 Cylindrical sealant backing serves one or more of the following functions:  
1.2.1 Limits the amount and depth of sealant applied into a joint,  
1.2.2 Acts as a bond breaker to allow joint movement without undue stress to the sealant,  
1.2.3 Provides a form to assist the sealant in developing the proper shape factor, and  
1.2.4 Acts as a barrier to the flow of sealant through the joint.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1087-23(Test Method)
Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems

SIGNIFICANCE AND USE
5.1 In structural sealant glazing systems, the sealant functions as the structural adhesive and may also function as the primary weather seal. As the structural adhesive, the integrity of the adhesive bond is critical.  
5.2 Changes in color and adhesion after exposure are two of the criteria that can be used to determine the compatibility of the system. Experience has shown that accessories that cause loss of adhesion or discoloration in this test method may also cause these occurrences in actual use.
SCOPE
1.1 This test method covers a laboratory screening procedure for determining the compatibility of liquid-applied structural sealant glazing sealants when in contact with accessories such as dry glazing gaskets, spacers, shims, and setting blocks after exposure to heat and ultraviolet light.  
1.2 This test method includes the observation of three parameters as follows:  
1.2.1 Changes in the color of the sealant,  
1.2.2 Changes in the adhesion of the sealant to glass, and  
1.2.3 Changes in the adhesion of the sealant to the accessory being tested.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: At this time, no comparable ISO standard exists.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1193-16(2023)(Guide)
Standard Guide for Use of Joint Sealants

SIGNIFICANCE AND USE
4.1 This guide provides information and guidelines for consideration by the designer or applicator of a joint seal. It explains the properties and functions of various materials, such as sealant, sealant backing, and primer, among others; and, procedures such as, substrate cleaning and priming, and installation of the components of a sealed joint. It presents guidelines for the use and application of the various materials, design of a sealant joint for a specific application, and environmental conditions and effects that are known to detrimentally affect a sealant joint. The information and guidelines are also useful for those that supply accessories to the sealant industry and for those that install sealants and accessory materials associated with sealant use.  
4.2 In addition to the design and installation data in this guide, consult the sealant manufacturer about applications for its products and their proper use and installation. Considering the range of properties of commercially available sealants, the variety of joint designs possible, and the many conditions of use, the information contained herein is general in nature.  
4.3 It should be realized that a sealant and sealant joint are expected to have a design life during which they remain functional. However, a sealant and sealant joint will also have a service life. The intent is for service life to meet or exceed design life. There are many factors that can affect service life including type of sealant polymer, sealant formulation, compatibility with adjacent materials, installation techniques or deficiencies, sealant joint design (or lack thereof), proper maintenance (or lack thereof), and environmental exposure, among others. The designer of a joint seal should take the above into consideration when designing and specifying sealants for certain applications.  
4.4 The design life of a sealant or sealant joint should be considered in conjunction with the design life of the structure for which it is us...
SCOPE
1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.  
1.2 An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834, C920, or C1311.  
1.3 This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information.  
1.4 Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.  
1.5 This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.  
1.7 The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and e...

  • Guide
    33 pages
    English language
    sale 15% off
ASTM
ASTM C793-23(Test Method)
Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants

SIGNIFICANCE AND USE
5.1 It is known that solar radiation contributes to the degradation of sealants in exterior building joints. The use of a laboratory accelerated weathering machine with actinic radiation, moisture and heat appears to be a feasible means to give indications of early degradation by the appearance of sealant cracking. However, simulated weather factors in combination with extension may produce more severe degradation than weather factors only. Therefore, the effect of the weathering test is made more sensitive by the addition of the bending of the specimen at cold temperature.
SCOPE
1.1 This test method covers a laboratory procedure for determining the effects of accelerated weathering on cured-in-place elastomeric joint sealants (single- and multicomponent) for use in building construction.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C782-13(2023)(Test Method)
Standard Test Method for Softness of Preformed Tape Sealants

SIGNIFICANCE AND USE
5.1 Preformed tape sealants are tacky, deformable solids that are used under compression between two substrates in a variety of sealing applications. This procedure measures the softness of a preformed tape sealant and gives an indication of the preformed tape sealant's ease of compression during installation. The resistance to penetration may also give an indication of the toughness of the preformed tape sealant.
SCOPE
1.1 This test method describes a laboratory procedure for determining the softness of preformed tape sealants.  
Note 1: Cone penetration methods applicable to greases and to petrolatum are described in Test Methods D217 and D937. Test Method D2451 also uses a penetration technique for determining the degree of set in sash glazing compounds.  
1.2 The values stated in SI units are to be regarded as standard. Temperature values are also provided (in parentheses) in degrees Fahrenheit.  
1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off