ASTM F822-93(2017)

Standard Specification for Chest of Drawers (Chiffonier), Steel, Marine

ABSTRACT
This specification covers the design, dimensional, and performance requirements for the manufacture of marine chests of drawers (chiffoniers) of steel construction to be used in staterooms and other spaces. All material, workmanship, and finish shall be of specified quality in keeping with the best commercial marine practice so as to produce each item suitable for its intended use.
SCOPE
1.1 This specification covers the construction of marine chests of drawers (chiffoniers) of steel construction to be used in staterooms and other spaces.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 31-Dec-2016
• ICS: 47.020.80 - Accommodation spaces
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F822 −93 (Reapproved 2017) An American National Standard
Standard Specification for
Chest of Drawers (Chiffonier), Steel, Marine
ThisstandardisissuedunderthefixeddesignationF822;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4.1.2 Paint:
4.1.2.1 Color—Purchaser shall pick from manufacturer’s
1.1 This specification covers the construction of marine
samples or submit sample chip of color desired.
chests of drawers (chiffoniers) of steel construction to be used
4.1.2.2 Manufacturer’s standard baked enamel will be fur-
in staterooms and other spaces.
nished unless otherwise required and indicated by the pur-
1.2 The values stated in inch-pound units are to be regarded
chaser.
as standard. The values given in parentheses are mathematical
4.1.3 Options for Tops:
conversions to SI units that are provided for information only
4.1.3.1 Unless otherwise specified in the ordering
and are not considered standard.
documents, the top supplied by the furniture manufacturer may
be, at his option, Type I, II, III, or IV in accordance with
2. Referenced Documents
Specification F826.
2.1 ASTM Standards:
4.1.3.2 Color or pattern of top covering material shall be
A366/A366M Specification for Commercial Steel (CS)
specified.
Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled
4.1.4 Options for Drawers:
(Withdrawn 2000)
4.1.4.1 Padlock eyes shall be furnished on each drawer
D907 Terminology of Adhesives
when specified in ordering documents. This security device is
F825 Specification for Drawers, Furniture, Marine, Steel
normally used in crew living spaces.
F826 Specification for Tops, Furniture, Marine, Steel
4.1.4.2 Drawer locks shall be furnished when specified in
2.2 AISC Manual:
ordering documents. Master keying of drawer locks will not be
AISCWireandSheetMetalGauges EquivalentThicknessin
provided unless required and defined by the ordering docu-
Decimals of an Inch, U.S. Standard Gauge (USSG) for
ments. Instead, each drawer lock will be keyed differently. See
Uncoated Hot and Cold Rolled Sheets
Specification F825 for lock description.
4.1.4.3 Asecurity panel between the two middle drawers to
3. Terminology
provide two secure two-drawer storage areas for two crew
3.1 Definitions of Terms Specific to This Standard:
members is only furnished when specified in ordering docu-
3.1.1 chest of drawers (chiffonier)—a chest of drawers with
ments.All four drawers in this type chest will be of same size.
four drawers. All four drawers may be of the same size.
4.1.5 If the total weight of the chest of drawers is required,
it shall be requested by the purchaser.
4. Ordering Information
4.1 Orders for items purchased under this specification shall
5. Materials and Manufacture
include the following information:
5.1 For typical design, see Fig. 1.
4.1.1 Quantity.
5.2 Sheet metal shall be in accordance with Specification
A366/A366M, commercial quality.
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on 5.2.1 Minimum sheet metal thicknesses shall be:
Outfitting and Deck Machinery.
5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2
Current edition approved Jan. 1, 2017. Published January 2017. Originally
mm).
approved in 1983. Last previous edition approved in 2010 as F822 – 93 (2010).
5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).
DOI: 10.1520/F0822-93R17.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
5.3 Joining of Metal Components:
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
5.3.1 Metal components shall be joined by welding or
The last approved version of this historical standard is referenced on
gluing with a structural adhesive as defined in Terminology
www.astm.org.
D907. The back panel may be riveted to the case provided
Available from American Institute of Steel Construction (AISC), 130 E.
Randolph St., Suite 2000, Chicago, IL 60601-6219, http://www.aisc.org. rivets are not visible after installation.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F822−93 (2017)
NOTE 1—For description of Type I, II, III, and IV tops, see Specification F826.
NOTE 2—For descriptio
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F822 − 93 (Reapproved 2010) F822 − 93 (Reapproved 2017)An American National Standard
Standard Specification for
Chest of Drawers (Chiffonier), Steel, Marine
This standard is issued under the fixed designation F822; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the construction of marine chests of drawers (chiffoniers) of steel construction to be used in
staterooms and other spaces.
1.2 Values The values stated in inch-pound units are to be regarded as the standard. The metric equivalents, values given in
parentheses, are parentheses are mathematical conversions to SI units that are provided for information only. only and are not
considered standard.
2. Referenced Documents
2.1 ASTM Standards:
A366/A366M Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled (Withdrawn
2000)
D907 Terminology of Adhesives
F825 Specification for Drawers, Furniture, Marine, Steel
F826 Specification for Tops, Furniture, Marine, Steel
2.2 American Institute of Steel Construction AISC Manual:
AISC Wire and Sheet Metal Gages—Gauges Equivalent Thickness in Decimals of an Inch, U.S. Standard Gauge (USSG) for
Uncoated Hot and Cold Rolled Sheets
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 chest of drawers (chiffonier)—a chest of drawers with four drawers. All four drawers may be of the same size.
4. Ordering Information
4.1 Orders for items purchased under this specification shall include the following information:
4.1.1 Quantity.
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved March 1, 2010Jan. 1, 2017. Published April 2010January 2017. Originally approved in 1983. Last previous edition approved in 20042010 as
F822 – 93 (2004).(2010). DOI: 10.1520/F0822-93R10.10.1520/F0822-93R17.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
The last approved version of this historical standard is referenced on www.astm.org.
Available from American Institute of Steel Construction (AISC), One130 E. Wacker Dr.,Randolph St., Suite 700,2000, Chicago, IL 60601-2001,60601-6219,
http://www.aisc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F822 − 93 (2017)
4.1.2 Paint:
4.1.2.1 Color—Purchaser shall pick from manufacturer’s samples or submit sample chip of color desired.
4.1.2.2 Manufacturer’s standard baked enamel will be furnished unless otherwise required and indicated by the purchaser.
4.1.3 Options for Tops:
4.1.3.1 Unless otherwise specified in the ordering documents, the top supplied by the furniture manufacturer may be, at his
option, Type I, II, III, or IV in accordance with Specification F826.
4.1.3.2 Color or pattern of top covering material shall be specified.
4.1.4 Options for Drawers:
4.1.4.1 Padlock eyes shall be furnished on each drawer when specified in ordering documents. This security device is normally
used in crew living spaces.
4.1.4.2 Drawer locks shall be furnished when specified in ordering documents. Master keying of drawer locks will not be
provided unless required and defined by the ordering documents. Instead, each drawer lock will be keyed differently. See
Specification F825 for lock description.
4.1.4.3 A security panel between the two middle drawers to provide two secure two-drawer storage areas for two crew members
is only furnished when specified in ordering documents. All four drawers in this type chest will be of same size.
4.1.5 If the total weight of the chest of drawers is required, it shall be requested by the purchaser.
5. Materials and Manufacture
5.1 For typical design, see Fig. 1.
5.2 Sheet metal shall be in accordance with Specification A366/A366M, commercial quality.
5.2.1 Minimum sheet metal thicknesses shall be:
5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2 mm).
5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).
5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).
5.3 Joining of Metal Components : Components:
NOTE 1—For description of Type I, II, III, and IV tops, see Specification F826.
NOTE 2—For descri
...