iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C915-79(2010)

(Specification)

Standard Specification for Precast Reinforced Concrete Crib Wall Members

Standard Specification for Precast Reinforced Concrete Crib Wall Members

ABSTRACT
This specification covers open- and closed-face precast reinforced concrete crib wall members for earth-retaining structures or protection against stream encroachment. The concrete crib wall shall conform to the dimensions prescribed in this specification. Manufacturing materials shall include portland cement, aggregates, chemical admixtures, water, and steel reinforcement. Manufacturing shall conform to the procedures which include mixing, reinforcement-concrete placing, forming, curing, cleaning, oiling, and finishing. Compression tests shall be made on standard concrete cylinders and shall conform to the design strength indicated in this specification.
SCOPE
1.1 This specification covers open- and closed-face precast reinforced concrete crib walls intended to act as earth-retaining structures or as protection against stream encroachment.
Note 1—This specification is a manufacturing and purchase specification only, with examples and suggestions for usage. Successful performance of this product depends on the proper selection and assembling of members, proper foundation and bearing material, and consideration of backfill heights, backfill material, drainage, and other engineering and construction considerations. The purchaser of the crib wall members specified herein is cautioned that he must properly correlate the field requirements with the members selected and provide adequate inspection at the construction site.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

Status
Historical
Publication Date
30-Jun-2010
ICS
91.100.30 - Concrete and concrete products
Technical Committee
C27 - Precast Concrete Products
Drafting Committee
C27.20 - Architectural and Structural Products
Current Stage
Ref Project

Relations

Replaces
ASTM C915-79(2002) - Standard Specification for Precast Reinforced Concrete Crib Wall Members
Effective Date
01-Jul-2010
Replaced By
ASTM C915-79(2018) - Standard Specification for Precast Reinforced Concrete Crib Wall Members
Effective Date
01-Jul-2018

Buy Standard

ASTM C915-79(2010) - Standard Specification for Precast Reinforced Concrete Crib Wall MembersASTM C915-79(2010) - Standard Specification for Precast Reinforced Concrete Crib Wall Members
PreviousNext
Technical specification
ASTM C915-79(2010) - Standard Specification for Precast Reinforced Concrete Crib Wall Members
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C915 −79 (Reapproved 2010)
Standard Specification for
Precast Reinforced Concrete Crib Wall Members
This standard is issued under the fixed designation C915; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C42/C42M Test Method for Obtaining and Testing Drilled
Cores and Sawed Beams of Concrete
1.1 This specification covers open- and closed-face precast
C94/C94M Specification for Ready-Mixed Concrete
reinforced concrete crib walls intended to act as earth-retaining
C150 Specification for Portland Cement
structures or as protection against stream encroachment.
C173/C173M Test Method forAir Content of Freshly Mixed
NOTE 1—This specification is a manufacturing and purchase specifica-
Concrete by the Volumetric Method
tion only, with examples and suggestions for usage. Successful perfor-
C231 Test Method for Air Content of Freshly Mixed Con-
mance of this product depends on the proper selection and assembling of
crete by the Pressure Method
members, proper foundation and bearing material, and consideration of
C260 Specification for Air-Entraining Admixtures for Con-
backfill heights, backfill material, drainage, and other engineering and
construction considerations. The purchaser of the crib wall members
crete
specified herein is cautioned that he must properly correlate the field
C309 Specification for Liquid Membrane-Forming Com-
requirements with the members selected and provide adequate inspection
pounds for Curing Concrete
at the construction site.
C330 Specification for Lightweight Aggregates for Struc-
1.2 The values stated in inch-pound units are to be regarded
tural Concrete
as the standard. The values given in parentheses are for
C494/C494M Specification for Chemical Admixtures for
information only.
Concrete
C595 Specification for Blended Hydraulic Cements
2. Referenced Documents
C618 Specification for Coal Fly Ash and Raw or Calcined
2.1 ASTM Standards:
Natural Pozzolan for Use in Concrete
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
3. Classification
A615/A615M SpecificationforDeformedandPlainCarbon-
3.1 Cribbing manufactured in accordance with this specifi-
Steel Bars for Concrete Reinforcement
cation shall be of open- or closed-face design and shall
A616/A616M Specification for Rail-Steel Deformed and
conform to the standard designs shown in Figs. 1-4.
Plain Bars for Concrete Reinforcement (Withdrawn
1999)
4. Ordering Information
A617/A617M Specification for Axle-Steel Deformed and
Plain Bars for Concrete Reinforcement (Withdrawn
4.1 Acceptability of the crib wall members in all cross
1999)
sections and lengths produced in accordance with Section 6
C31/C31M Practice for Making and Curing Concrete Test
shallbedeterminedbytheresultsofcylindercompressiontests
Specimens in the Field
of the placed concrete and mill certificates for the reinforcing
C33 Specification for Concrete Aggregates
steel and cement. A written statement, signed by the
C39/C39M Test Method for Compressive Strength of Cylin-
manufacturer, shall verify that the cement, aggregate,
drical Concrete Specimens
admixtures, and reinforcing steel conform to the specifications
for materials in Section 5 and that the preparation of
equipment, mixing, conveying, placing, consolidating, and
This specification is under the jurisdiction ofASTM Committee C27 on Precast
curing meet requirements of the applicable standard specifica-
Concrete Products and is the direct responsibility of Subcommittee C27.20 on
tions. The concrete strength as determined by the cylinder
Architectural and Structural Products.
Current edition approved July 1, 2010. Published August 2010. Last previous
compression tests shall be as specified in 6.3, and the test
edition approved in 2002 as C915 – 79 (2002). DOI: 10.1520/C0915-79R10.
method shall conform to the requirements of Test Method
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C39/C39M. The manufacturer’s statement shall also certify
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
adherence to tolerance dimensions of Section 9.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
4.2 Acceptability of the concrete strength of completed
The last approved version of this historical standard is referenced on
www.astm.org. cribbing produced in accordance with Section 6 may also be
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C915−79 (2010)
NOTE 1—Surface drainage should not be permitted to flow directly against the face of the cribbing.
NOTE 2—Walls should be separated into 96-ft sections by the provision of double rows of headers.
NOTE 3—In using these typical sections for designing walls of intermediate height, the drawing should be read from the top down until the desired
height is reached. Base details are repeated for intermediate heights.
NOTE 4—In areas of aggressive environment, Type II cement or protective coatings, or both, may need to be used to avoid deterioration of the walls.
3 3
NOTE 5—Metric Conversion: 1 ft = 304.8 1 in. = 25.4 mm 1 lb = 0.453592 kg 1 ft = 0.028317 m
FIG. 1 Open-Faced Concrete Crib Wall
determined by compressive tests of concrete cores in accor- other substances that may be deleterious to concrete or steel; it
dance with Test Method C42/C42M. should not contain concentrations of chlorides in excess of
1000 ppm or sulfates in excess of 1000 ppm.
5. Materials
5.4.1 Ifwaterofhigherchloridecontentisusedbyreasonof
nonavailability of water of recommended quality, the manu-
5.1 Cement—Portland cement shall conform to the require-
facturer must obtain approval from the user.
ments of Specification C150 or shall be portland blast-furnace
slag cement or portland-pozzolan cement conforming to the
5.5 Steel Reinforcement—Steel reinforcement shall consist
requirements of Specification C595.
of bars conforming to Specifications A615/A615M, A616/
A616M,or A617/A617M.
5.2 Aggregates—Aggregates shall conform to Specification
C33 or C330. The nominal maximum size aggregate shall not
6. Design
be greater than ⁄4 in. (19.0 mm).
6.1 Precast concrete crib wall members shall conform to
5.3 Admixtures—Air-entrainingadmixturesshallconformto
details and dimensions prescribed in Figs. 1-4, subject to the
Specification C260. Chemical admixtures shall conform to
provisions of this section and Section 10.
Specification C494/C494M. Fly ash or other pozzolanic ad-
mixtures shall conform to the requirements of Specification 6.2 Reinforcement—Minimum reinforcement shall be as
C618. shown in Fig. 2 and Fig. 4 and shall be Grade 40 or 60.
5.4 Water—Water used for curing, washing aggregates, and 6.3 Concrete—Concrete shall have a minimum design com-
mixing concrete shall be free of oils, organic materials, and pressive strength of 4000 psi (28 MPa) in 28 days.
C915−79 (2010)
NOTE 1—All reinforcing to be No. 3 bars placed 1 ⁄4 in. clear from surface of concrete.
NOTE 2—Bars to be held in position by chairs having noncorrosive tips.
NOTE 3—Blocks shall be set in cement-sand mortar (1 to 3).
NOTE 4—Backfilling should follow closely the erection of the successive tiers of units, and the wall should not be erected higher than 3 ft above the
backfilled portion at any time.
NOTE 5—Gravel, crushed stone, or other granular material meeting the users’ specifications may be used as backfill material. Rock may also be used,
but care should be used to avoid damaging or dislodging the crib units. Clay or material having a large percentage of clay is not to be used.
NOTE 6—Cribbing should be placed on a foundation of firm bearing material. This foundation should be at least 3 ft below the surface of the ground,
beyondalldangeroffrost,unlessonsolidrock.Ifthestretchersarelocateddirectlyaboverock,acushionofsandorgravelnotlessthan6in.thickshould
be provided.
NOTE 7—All headers are placed at 6 ft 0 in. center to center.
NOTE 8—Details of steps are similar to those shown on Fig. 4.
FIG. 2 Open-Faced Concrete Crib Wall
6.4 Concrete Cover—The minimum concrete cover over the such that the crib wall members will conform to the test and
reinforcement shall be 1 ⁄4 in. (32 mm).
design requirements of this specification.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1560-03(2023)(Test Method)
Standard Test Method for Hot Water Accelerated Aging of Glass-Fiber Reinforced Cement-Based Composites

SIGNIFICANCE AND USE
3.1 The basis for this test as an indicator of the long term behavior of fiber reinforced composites is that elevated temperature and moisture content accelerate the formation of the products of hydration of the cement in the matrix, particularly calcium hydroxide.  
3.1.1 It is known that the interaction of these products of hydration, particularly calcium hydroxide, with the fibers can have a major effect on the long-term properties of the composites.  
3.1.2 The principal mechanism that occurs is that the calcium hydroxide forms within the bundles of filaments that form the glass fiber strand. This gradually bonds the filaments together, which reduces filament pull-out. This causes a reduction in the strain capacity of the composite, thereby reducing the strength of the composite and changing the composite from a ductile material to an increasingly brittle material.  
3.1.3 Accelerating the formation of the hydration products accelerates their interaction with the fibers, hence accelerating the aging of the composite.  
3.2 The data developed from this test are used by researchers and manufacturers to evaluate the long-term performance of different mixtures, reinforcements, mixture components, and to provide data for the development of design procedures for products made from these composites.  
3.2.1 The recorded data also provides screening information as new matrices and reinforcements are developed.  
3.3 The usefulness of the test as an indicator of long term composite performance is valid if the only reactions that are accelerated are those that occur more slowly under natural weathering, hot water can induce effects in some composites, for instance those containing acrylic polymer, that may not occur in natural weathering. This test method may not be a valid indicator of long-term performance of such composites.
SCOPE
1.1 This test method provides a way of accelerating the aging of glass fiber reinforced cementitious composites in order to develop data that will indicate real-life natural weathering performance.  
1.2 The coupons prepared for this test method will be tested using Test Method C947.  
1.3 This test method can be used to age coupons for other test methods.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1228-96(2023)(Practice)
Standard Practice for Preparing Coupons for Flexural and Washout Tests on Glass Fiber Reinforced Concrete

SIGNIFICANCE AND USE
3.1 Flexural strengths, as determined by Test Method C947, are used for quality control and design of GFRC products and may be used to verify compliance with specifications and to collect data in research and development programs. It is, therefore, important that coupons be prepared according to a standard practice. The coupons are used to make test specimens for Test Method C947 and for Test Method C1229 to determine the amount of glass fiber reinforcement per unit volume of GFRC for quality control purposes.
SCOPE
1.1 This practice covers preparation of test coupons to be used in tests of plant manufactured thin-section glass fiber reinforced concrete (GFRC).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1230-96(2023)(Test Method)
Standard Test Method for Performing Tension Tests on Glass-Fiber Reinforced Concrete (GFRC) Bonding Pads

SIGNIFICANCE AND USE
3.1 Tensile loads determined by this test method are useful for quality control of GFRC architectural panels manufactured using the steel panel frame support design. In addition, test results may be used to verify compliance with governing specifications, research and development, and generating data for use in product design.
SCOPE
1.1 This test method covers determination of the tensile load capacity of glass-fiber reinforced concrete (GFRC) bonding pads used for attaching steel anchors to GFRC architectural panels.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C947-03(2023)(Test Method)
Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading)

SIGNIFICANCE AND USE
3.1 Flexural properties determined by this test method are useful for quality control of glass-fiber reinforced concrete products, ascertaining compliance with the governing specifications, research and development, and generating data for use in product design.
SCOPE
1.1 This test method covers determination of the flexural ultimate strength in bending and the yield strength of glass-fiber reinforced concrete sections by the use of a simple beam of 1.0 in. (25.4 mm) or less in depth using third-point loading.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C948-81(2023)(Test Method)
Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete

SIGNIFICANCE AND USE
2.1 Material properties determined by this test method are useful for quality control of glass-fiber reinforced concrete, ascertaining compliance with governing specifications, and research and development.
SCOPE
1.1 This test method covers the determinations of dry and wet bulk density, water absorption, and apparent porosity of thin sections of glass-fiber reinforced concrete.  
Note 1: This test method does not involve a determination of absolute specific gravity. Therefore, such pore space as may be present in the specimen that is not emptied during the specified drying or is not filled with water during the specified immersion is considered “impermeable” and is not differentiated from the solid portion of the specimen for the calculations, especially those for percent voids.
Depending upon the pore size distribution and the pore entry radii of the specimen and on the purposes for which the test results are desired, the procedures of this method may be adequate, or they may be insufficiently rigorous. In the event that it is desired to fill more of the pores than will be filled by immersion, various techniques involving the use of vacuum treatment or increased pressure may be used. If a rigorous measure of total pore space is desired, this can only be obtained by determining absolute specific gravity by first reducing the sample to discrete particles, each of which is sufficiently small so that no impermeable space can exist within any of the particles.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1229-94(2023)(Test Method)
Standard Test Method for Determination of Glass Fiber Content in Glass Fiber Reinforced Concrete (GFRC) (Wash-Out Test)

SIGNIFICANCE AND USE
4.1 Glass fiber contents, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of glass fiber reinforcement in a GFRC composite.
SCOPE
1.1 This test method covers determination of the fiber content in an uncured, glass fiber reinforced concrete (GFRC) sample panel.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C890-21(Practice)
Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures

SIGNIFICANCE AND USE
4.1 This practice is intended to standardize the minimum loads to be used to structurally design a precast product.  
4.2 The user is cautioned that he must properly correlate the anticipated field conditions and requirements with the design loads. Field conditions may dictate loads greater than minimum.
SCOPE
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478/C478M.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1889-21(Practice)
Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Utility, Water, and Wastewater Structures Using AASHTO LRFD Design

SIGNIFICANCE AND USE
4.1 This practice is intended to standardize the minimum structural loads used to design a precast concrete product using AASHTO LRFD.  
4.2 The user is cautioned to properly correlate the anticipated field conditions and requirements with the design loads. Field conditions may dictate loads greater than described here.
SCOPE
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete utility structures, or sectional precast concrete water and wastewater structures, where AASHTO LRFD design is required. Concrete pipe, box culverts, and material covered in Specification C478 are excluded from this practice. Structures not requiring AASHTO LRFD design are to be designed using the loads specified in ASTM C857 or ASTM C890, as applicable.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1824-16(2021)(Test Method)
Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles

SIGNIFICANCE AND USE
5.1 This test method is intended to provide the user with acceptable apparatus requirements and a prescribed procedure to determine the bending moment capacity of spun pre-stressed concrete bases for use with tapered steel poles.  
5.2 The results of this test method are used as a basis for verification of calculated bending moment capacity, quality control tool for manufacturing process and as a basis for determining statistical bending moment capacity.  
5.3 This test method shall not be used for full length prestressed concrete, steel, or composite poles.
SCOPE
1.1 This test method covers determination of ultimate bending moment capacity and cracking moment capacity of concrete bases used as foundations for tapered steel lighting poles in accordance to Specification C1804.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C891-20(Practice)
Standard Practice for Installation of Underground Precast Concrete Utility Structures

ABSTRACT
This practice covers the procedures to be followed in the planning, site preparation, and installation of underground precast concrete utility structures. The installation area shall be surveyed using the workprint and a checklist to identify the work to be done and to determine that the plans are correct. Permits required to do work in accordance with the detail plans shall be secured before starting the job. All permits or a record of the permits shall be retained on the job for immediate reference. Safety requirements for construction shall be in accordance with all federal, state, and local regulations. Shoring for construction shall be in accordance with all federal, state, and local regulations.
SCOPE
1.1 This practice covers the procedures to be followed in the planning, site preparation, and installation of underground precast concrete utility structures. Concrete pipe and box culverts are not covered under this practice. Also, precast concrete manholes covered in Specification C478/C478M are excluded from this practice.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off