ASTM D6364-06(2018)
(Test Method)Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics
Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics
SIGNIFICANCE AND USE
5.1 The compression behavior test for geosynthetics is intended to be an index test. It is anticipated that the results of the compression behavior test will be used to evaluate product. The results of the analyses may also be used to compare the relative compressive yield points of materials that exhibit a detectable compressive yield point. It is anticipated that this test will be used for quality control testing to evaluate uniformity and consistency within a lot or between lots where sample geometry factors (for example, thickness) or materials may have changed.
Note 1: This is a one-dimensional test for compressive loading of a geosynthetic(s) in one plane.
5.1.1 The compressive yield point of geosynthetics may be evaluated from the stress/strain relationship. Many materials exhibit compressive deformation but may not show a distinct compressive yield point.
5.2 This test method can be used to evaluate the short-term stress/strain behavior of geosynthetics under compressive stress while loaded at a constant rate of deformation.
5.3 This test method may be used for acceptance testing of commercial shipments of geosynthetics, but caution is advised because interlab testing is incomplete.
5.3.1 In the case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. At a minimum, two parties should take a group of test specimens from material shipped to the project. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using the Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If...
SCOPE
1.1 This test method covers the procedures for evaluation of the deformations of a geosynthetic or combination of geosynthetics (that is, geocomposite (excluding geotextiles, geomembranes, and geosynthetic clay liners)) under short-term compressive loading. This test method is strictly an index test method to be used to verify the compressive strength consistency of a given manufactured geosynthetic(s). Results from this test method should not be considered as an indication of actual or long-term performance of the geosynthetic(s) in field applications.
1.2 Since these geosynthetics may experience multidirectional compressive loadings in the field, this test method will not show actual field performance and should not be used for this specific objective. The evaluator of the results should also recognize that the determination of the short-term single-plane compressive behavior of geosynthetics does not reflect the installed performance of synthetic drainage systems and, therefore, should not be used as the only method of product specification or performance with respect to synthetic drainage systems.
1.3 The values in SI units are to be regarded as the standard. Values in inch-pound units are provided in parentheses for information.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6364 − 06 (Reapproved 2018)
Standard Test Method for
Determining Short-Term Compression Behavior of
1
Geosynthetics
This standard is issued under the fixed designation D6364; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This test method covers the procedures for evaluation of 2.1 ASTM Standards:
the deformations of a geosynthetic or combination of geosyn- D4354 Practice for Sampling of Geosynthetics and Rolled
thetics (that is, geocomposite (excluding geotextiles, Erosion Control Products (RECPs) for Testing
geomembranes,andgeosyntheticclayliners))undershort-term D4439 Terminology for Geosynthetics
compressive loading. This test method is strictly an index test D5199 Test Method for Measuring the Nominal Thickness
method to be used to verify the compressive strength consis- of Geosynthetics
tency of a given manufactured geosynthetic(s). Results from D7001 Specification for Geocomposites for Pavement Edge
this test method should not be considered as an indication of Drains and Other High-Flow Applications
actual or long-term performance of the geosynthetic(s) in field
3. Terminology
applications.
3.1 Definitions:
1.2 Since these geosynthetics may experience multidirec-
3.1.1 compressive deformation, [L], n—thedecreaseingage
tional compressive loadings in the field, this test method will
length produced in the test specimen by a compressive load.
not show actual field performance and should not be used for
this specific objective. The evaluator of the results should also 3.1.2 compressive strain, [nd], n—the ratio of compressive
recognize that the determination of the short-term single-plane deformation to the gage length of the test specimen.
compressive behavior of geosynthetics does not reflect the
3.1.3 gage length, [L], n—in compression testing, the mea-
installed performance of synthetic drainage systems and,
sured thickness of the test specimen under specified compres-
therefore, should not be used as the only method of product
sional force, expressed in units of length prior to compressive
specification or performance with respect to synthetic drainage
loading. (D5199)
systems.
3.1.4 geocomposite, n—a product fabricated from any com-
1.3 The values in SI units are to be regarded as the standard.
bination of geosynthetics with geotechnical materials or other
Values in inch-pound units are provided in parentheses for
synthetics that is used in a geotechnical application.
information.
3.1.5 geosynthetic, n—a planar product manufactured from
1.4 This standard does not purport to address all of the
polymeric material used with foundation, soil, rock, earth, or
safety concerns, if any, associated with its use. It is the
any other geotechnical engineering-related material as an
responsibility of the user of this standard to establish appro-
integral part of a man-made project, structure, or system.
priate safety, health, and environmental practices and deter-
(D4439)
mine the applicability of regulatory limitations prior to use.
3.1.6 index test, n—a test procedure that may contain a
1.5 This international standard was developed in accor-
known bias but that may be used to establish an order for a set
dance with internationally recognized principles on standard-
of specimens with respect to the property of interest. (D4439)
ization established in the Decision on Principles for the
3.1.7 yield point, n—the first point on the load-deformation
Development of International Standards, Guides and Recom-
curve at which an increase in deformation occurs without a
mendations issued by the World Trade Organization Technical
corresponding increase in load.
Barriers to Trade (TBT) Committee.
3.1.7.1 Discussion—Some geosynthetics do not exhibit an
exact yield point. The tested geosynthetic may exhibit a less
1
This test method is under the jurisdiction of ASTM Committee D35 on
Geosynthetics and is the direct responsibility of Subcommittee D35.01 on Mechani-
2
cal Properties. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2018. Published February 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1999. Last previous edition approved in 2011 as D6364 – 06 (2011). Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/D6364-06R18. the ASTM website.
Copyright © ASTM Inter
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.