ASTM F1006-86(1997)
(Specification)Standard Specification for Entrainment Separators for Use in Marine Piping Applications
Standard Specification for Entrainment Separators for Use in Marine Piping Applications
SCOPE
1.1 This specification provides the minimum requirements for the pressure-temperature rating, testing, and making of pressure containing vessels for entrainment separators.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: F 1006 – 86 (Reapproved 1997)
Standard Specification for
Entrainment Separators for Use in Marine Piping
Applications
This standard is issued under the fixed designation F 1006; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
1. Scope 2.3 Manufacturer’s Standardization Society of the Valve
and Fittings Industry Standard:
1.1 This specification provides the minimum requirements
MSSSP-51 150 LB Corrosion Resistant Cast Flanges and
for the pressure-temperature rating, testing, and making of
Flanged Fittings
pressure containing vessels for entrainment separators.
2.4 Military Standard:
1.2 The values stated in inch-pound units are to be regarded
MIL-F-1183 Fittings Tube, Bronze, Cast (Silver Brazings)
as the standard. The values given in parentheses are for
information only.
3. Definitions of Terms Specific to This Standard
1.3 The following safety hazards caveat pertains only to the
3.1 entrainment separator—a mechanical device inserted in
test methods portion, Section 6, of this specification: This
a pipeline which by centrifugal force, baffles, or other means
standard does not purport to address all of the safety concerns,
will separate a liquid from a gas (vapor).
if any, associated with its use. It is the responsibility of the user
3.2 hydrostatic test—the act of filling an entrainment sepa-
of this standard to establish appropriate safety and health
rator vessel with water and applying internal pressure to all
practices and determine the applicability of regulatory limita-
parts of the vessel.
tions prior to use.
3.3 master gage—the calibrated gage used to verify the
2. Referenced Documents accuracy of the test gage. This gage shall be recalibrated
traceable to the National Bureau of Standards.
2.1 ANSI Standards:
3.4 pressure rating—the maximum working pressure of an
B2.1 Pipe Threads (Except Dryseal)
entrainment separator when operated at a specific temperature.
B16.1 Cast Iron Pipe Flanges and Flanged Fittings
3.5 proof test—the act of filling an entrainment separator
B16.3 Malleable Iron Threaded Fittings, Class 150 and
vessel with water and applying internal pressure to all parts of
the vessel for the purpose of causing yielding of the vessel and
B16.4 Cast Iron Threaded Fittings, Class 125 and 250
bursting of the vessel.
B16.5 Steel Pipe Flanges and Flanged Fittings
3.6 temperature ratings—minimum and maximum tem-
B16.11 Forged Steel Fittings, Socket Welding and
peratures at which the entrainment separator may be operated
Threaded
2 while at specific pressures.
B16.15 Cast Bronze Threaded Fittings, Class 150 and 300
3.7 test gage—the pressure gage that is used to check the
B16.24 Bronze Flanges and Flanged Fittings, Class 150 and
2 internal pressure of the entrainment separator. The test gage
shall be calibrated at least annually or at any time it is
B16.25 Buttwelding Ends
2 suspected to be in error by a calibrated master gage.
B16.31 Nonferrous Pipe Flanges
2.2 ASME Standards:
4. Materials and Manufacture
SA278 Cast Gray Iron Pressure Vessels
3 4.1 The pressure-temperature ratings established under this
SA395-60 Cast Ductile Iron
specification are based upon the manufacturer’s usage of high
Boiler and Pressure Vessel Code, Section VIII
3 quality materials produced under regular control of chemical
Boiler and Pressure Vessel Code, Section II
and physical properties by a recognized process. The manu-
facturershallbepreparedtosubmitcertificationofcompliance,
verifying that his product has been so produced and that it has
This specification is under the jurisdiction of Committee F-25 on Ships and
Marine Technology and is the direct responsibility of Subcommittee F25.13 on
Piping Systems.
Current edition approved July 25, 1986. Published September 1986.
2 4
Available from American National Standards Institute, 11 W. 42nd St., 13th Available from Manufacturer’s Standardization Society of the Valve and
Floor, New York, NY 10036. Fittings Industry, 127 Park St., N.E., Vienna, VA 22180.
3 5
Available from American Society of Mechanical Engineers, 345 E. 47th St., AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
New York, NY 10017. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
F 1006 – 86 (1997)
been manufactured from material with chemical and physical 5.2.3.3 Test water temperature and entrainment separator
properties at least equal to the requirements of the appropriate temperature must be at equilibrium before hydrostatic test
standard or specification listed in 4.3 of this specification or pressure is applied.
Section II of the ASME Boiler and Pressure Vessel Code. 5.2.3.4 All possible air pockets must be purged while the
entrainment separator vessel is being filled with water. Ad-
4.2 For materials not having values of allowable stress
equate vents shall be provided at all high points of the vessel.
tabulated in Section VIII Division I of the ASME Boiler and
5.2.3.5 External equipment not to be pressurized with the
PressureVesselCode,allowablestressesshallbedeterminedin
entrainment separator should be isolated or disconnected
accordance with the procedures outlined in Appendix P of
before applying the hydrostatic test pressure.
Section VIII, Division 1 of the ASME Boiler and Pressure
5.2.3.6 Hydrostatic test pressure shall be applied gradually
Vessel Code.
to t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.