iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1372-01

(Specification)

Standard Specification for Segmental Retaining Wall Units

Standard Specification for Segmental Retaining Wall Units

SCOPE
1.1 This specification covers segmental retaining wall units of concrete, machine-made from portland cement, water, and suitable mineral aggregates with or without the inclusion of other materials. The units are intended for use in the construction of mortarless segmental retaining walls.
Note 1—When particular features are desired, such as weight classification, higher compressive strength, surface texture, finish, color, or other special features, such properties should be specified separately by the purchaser. Local suppliers should be consulted as to availability of units having the desired features.
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

Status
Historical
Publication Date
09-Aug-2001
ICS
91.060.10 - Walls. Partitions. Facades
Technical Committee
C15 - Manufactured Masonry Units
Drafting Committee
C15.03 - Concrete Masonry Units and Related Units
Current Stage
Ref Project

Relations

Replaces
ASTM C1372-00 - Standard Specification for Segmental Retaining Wall Units
Effective Date
10-Aug-2001
Replaced By
ASTM C1372-01a - Standard Specification for Segmental Retaining Wall Units
Effective Date
10-Aug-2001
Referred By
ASTM C140/C140M-23 - Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
Effective Date
10-Aug-2001
Referred By
ASTM C1232-21a - Standard Terminology for Masonry
Effective Date
10-Aug-2001
Referred By
ASTM C1262/C1262M-18 - Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
Effective Date
10-Aug-2001

Buy Standard

ASTM C1372-01 - Standard Specification for Segmental Retaining Wall UnitsASTM C1372-01 - Standard Specification for Segmental Retaining Wall Units
PreviousNext
Technical specification
ASTM C1372-01 - Standard Specification for Segmental Retaining Wall Units
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 1372 – 01
Standard Specification for
1
Segmental Retaining Wall Units
This standard is issued under the fixed designation C 1372; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
3
1. Scope * C 1232 Terminology of Masonry
C 1262 Test Method for Evaluating the Freeze-Thaw Dura-
1.1 This specification covers segmental retaining wall units
bility of Manufactured Concrete Masonry Units and Re-
of concrete, machine–made from portland cement, water, and
3
lated Concrete Units
suitable mineral aggregates with or without the inclusion of
other materials. The units are intended for use in the construc-
3. Terminology
tion of mortarless segmental retaining walls.
3.1 Terminology defined in Terminology C 1209 and Ter-
NOTE 1—When particular features are desired, such as weight classifi-
minology C 1232 shall apply for this specification.
cation, higher compressive strength, surface texture, finish, color, or other
special features, such properties should be specified separately by the
4. Materials
purchaser. Local suppliers should be consulted as to availability of units
4.1 Cementitious Materials—Materials shall conform to the
having the desired features.
following applicable specifications:
1.2 The text of this standard references notes and footnotes
4.1.1 Portland Cements—Specification C 150.
which provide explanatory material. These notes and footnotes
4.1.2 Modified Portland Cement—Portland cement con-
(excluding those in tables and figures) shall not be considered
forming to Specification C 150, modified as follows:
as requirements of the standard.
4.1.2.1 Limestone—Limestone, with a minimum 85 % Cal-
1.3 The values stated in inch-pound units are to be regarded
cium Carbonate (CaCO ) content, shall be permitted to be
3
as the standard. The values given in parentheses are for
added to the cement, provided these requirements of Specifi-
information only.
cation C 150 as modified are met:
(1) Limitation on Insoluble Residue—1.5 %.
2. Referenced Documents
(2) Limitation on Air Content of Mortar—Volume percent,
2.1 ASTM Standards:
22 % max.
2
C 33 Specification for Concrete Aggregates
(3) Limitation on Loss of Ignition—7 %.
C 140 Test Methods for Sampling and Testing Concrete
4.1.3 Blended Cements— Specification C 595 or C 1157.
3
Masonry Units and Related Units
4.1.4 Pozzolans—Specification C 618.
4
C 150 Specification for Portland Cement
4.1.5 Blast Furnace Slag Cement—Specification C 989.
C 331 Specification for Lightweight Aggregates for Con-
4.2 Aggregates—Aggregates shall conform to the following
2
crete Masonry Units
specifications, except that grading requirements shall not
4
C 595 Specification for Blended Hydraulic Cements
necessarily apply:
C 618 Specification for Coal Fly Ash and Raw or Calcined
4.2.1 Normal Weight Aggregates—Specification C 33.
Natural Pozzolan for Use as a Mineral Admixture in
4.2.2 Lightweight Aggregates—Specification C 331.
2
Concrete
4.3 Other Constituents—Air-entraining agents, coloring
C 989 Specification for Ground Granulated Blast-Furnace
pigments, integral water repellents, finely ground silica, and
2
Slag for Use in Concrete and Mortars
other constituents shall be previously established as suitable for
C 1157 Performance Specification for Blended Hydraulic
use in segmental retaining wall units and shall conform to
4
Cement
applicable ASTM standards or shall be shown by test or
C 1209 Terminology of Concrete Masonry Units and Re-
experience to be not detrimental to the durability of the
3
lated Units
segmental retaining wall units or any material customarily used
in segmental retaining wall construction.
1
This specification is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of C15.03 on Concrete
5. Physical Requirements
Masonry Units and Related Units.
5.1 At the time of delivery to the work site, the units shall
Current edition approved Jan. 10, 2001. Published February 2001. Originally
published as C 1372–97. Last previous edition C 1372–00.
conform to the physical requirements of Table 1 when tested in
2
Annual Book of ASTM Standards, Vol 04.02.
accordance with 8.2.
3
Annual Book of ASTM Standards, Vol 04.05.
4 5.2 Freeze-Thaw Durability—In areas where repeated
Annual Book of ASTM Standards, Vol 04.01.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C 1372
TABLE 1 Strength and Absorption Requirements
3 3
Minimum Required Net Average Compressive Maximum
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E519/E519M-22(Test Method)
Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages

SIGNIFICANCE AND USE
3.1 This test method was developed to measure more accurately the diagonal tensile (shear) strength of masonry than was possible with other available methods. The specimen size was selected as being the smallest that would be reasonably representative of a full-size masonry assemblage and that would permit the use of testing machines such as are used by many laboratories.
Note 1: As a research test method used only for the purpose of evaluating the effects of variables such as type of masonry unit, mortar, workmanship, etc., a smaller size specimen could be used if the available testing equipment will not accommodate a 1.2-m [4-ft] square specimen. However, there is a lack of experimental data that would permit an evaluation of the effect of specimen size on the shear strength or to permit a correlation between the results of small-scale specimen tests and larger specimens.
SCOPE
1.1 This test method covers determination of the diagonal tensile or shear strength of masonry assemblages by loading them in compression along one diagonal (see Fig. 1), thus causing a diagonal tension failure with the specimen splitting apart parallel to the direction of load.
FIG. 1 Apparatus for Determination of Diagonal Tensile or Shear Strength Masonry Assemblages  
1.2 Annex A1 provides requirements regarding the determination of the diagonal-tension strength of masonry under combined diagonal-tension and compressive loading.  
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C1197-22(Test Method)
Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method

SIGNIFICANCE AND USE
5.1 Deformation and strength properties are measured only on the masonry between flatjacks. Boundary effects of the collar joint behind the wythe tested and adjacent masonry are neglected. In the case of multi-wythe masonry, deformability is estimated only in the wythe in which the flatjack is inserted. Deformability of other wythes may be different.
SCOPE
1.1 This test method describes an in situ method for determining the deformation properties of existing unreinforced solid-unit masonry. (See Note 1.) This test method concerns the measurement of in-situ masonry deformability properties in existing masonry by use of thin, bladder-like flatjack devices that are installed in cut mortar joints in the masonry wall. This test method provides a relatively non-destructive means of determining masonry properties.
Note 1: Solid-unit masonry is that built with stone, concrete, or clay units whose net area is equal to or greater than 75 % of the gross area.  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C1072-22(Test Method)
Standard Test Methods for Measurement of Masonry Flexural Bond Strength

SIGNIFICANCE AND USE
5.1 This test method is intended for use in comparing the bond strengths (under the given conditions) of masonry mortars.  
5.2 This test method could be used, for example, to check one aspect of the quality of mortar products after production, or to indicate the bond potential of a mortar product without requiring the product to be tested in combination with many different units.  
5.3 This test method uses controlled conditions of fabrication and curing that are not intended to represent field conditions.  
5.4 This test method uses standard concrete masonry units. Mortars are batched by weight equivalents of volume proportions and are mixed to a prescribed flow. Prisms are constructed using a jig and are bag-cured.  
5.5 Flexural bond strength determined by this test method shall not be interpreted as the flexural bond strength of a wall (because standard units are not used for wall construction), nor shall it be interpreted as an indication of extent of bond for purposes of water permeability evaluation.
SCOPE
1.1 These test methods evaluate the flexural bond strength, normal to the bed joints, of masonry built of manufactured masonry units. Sampling and testing procedures are referenced, and terms are defined. Three different specimen fabrication methods are specified, each for a different purpose:  
1.1.1 The first method is the “Test Method for Laboratory-Prepared Specimens.” Its purpose is to compare the bond strengths (under the given conditions) of masonry mortars. It could be used, for example, to check the quality of mortar products after production, or to indicate the bond strength (under the given conditions) of a mortar product without requiring the product to be tested in combination with many different units. It is not intended to represent field conditions. It uses standard concrete masonry units. Mortars are batched by weight equivalents of volume proportions and are mixed to a prescribed flow. Prisms are constructed using a jig and are bag-cured.  
1.1.2 The second method is the “Test Method for Field-Prepared Specimens.” Its purpose is to evaluate the bond strength (under the given conditions) of a particular unit-mortar combination, either for preconstruction evaluation of materials or for quality control purposes during construction. Mortars are batched conventionally, and the flow is not prescribed. Prisms are constructed conventionally (no jig) and are bag-cured.  
1.1.3 The third method is the “Test Method for Prisms Removed from Existing Masonry.” Its purpose is to evaluate the bond strength of unit-mortar combinations of prisms cut from existing walls.  
1.1.4 The three methods are not consistent, nor are they intended to be. They are intended to be used for three different purposes. To make this clear, the three methods are presented separately.  
1.1.5 Appendix X1 suggests two possible criteria for assessing the bond strength values obtained using these test methods. These possible evaluation criteria are given for illustration only and are not mandatory.  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Princip...

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM E518/E518M-22(Test Method)
Standard Test Methods for Flexural Bond Strength of Masonry

SIGNIFICANCE AND USE
4.1 These test methods are intended to provide simplified and economical means for gathering comparative research data on the flexural bond strength developed with different types of masonry units and mortar or for the purpose of checking job quality control (materials and workmanship).
Note 2: These test methods are not intended for use in establishing design stresses. For this purpose, Test Methods C1717 should be used.
SCOPE
1.1 These test methods cover determination of the flexural bond strength of unreinforced masonry assemblages. Two procedures are provided:  
1.1.1 Test Method A—Simply supported beam with third-point loading.  
1.1.2 Test Method B—Simply supported beam with uniform loading.
Note 1: Third-point loading (Test Method A) produces a moment distribution that is significantly different from uniformly distributed loading (Test Method B).Third-point loading (Test Method A) subjects more mortar joints to the maximum moment and thus, is likely to produce more conservative capacities than uniform loading (Test Method B).  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1196-20(Test Method)
Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements

SIGNIFICANCE AND USE
5.1 Stress is applied as pressure over the area of the flatjack. In the case of multi-wythe masonry, stress is estimated only in the wythe in which the flatjack is inserted. Stress in other wythes may be different.
SCOPE
1.1 This test method covers the determination of the average compressive stress in existing unreinforced solid-unit masonry (see Note 1). This test method concerns the measurement of in-situ compressive stress in existing masonry by use of thin, bladder-like flatjack devices that are installed in cut mortar joints in the masonry wall. This test method provides a relatively non-destructive means of determining masonry properties in place.
Note 1: Solid-unit masonry is that built with stone, concrete, or clay units whose net area is equal to or greater than 75 % of the gross area.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1717-19(Test Method)
Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels

SIGNIFICANCE AND USE
4.1 The test methods described in this standard are intended for use as a starting point in developing specific testing protocols for masonry elements.  
4.1.1 The testing protocols could be used for general research on the load-deflection behavior of masonry elements.  
4.1.2 The testing protocols could be used for qualification of masonry elements and materials by evaluation services and other parties.  
4.1.3 The test methods described in this standard are general, and are intended to be adaptable to address a wide range of anticipated support and loading conditions.  
4.2 How the test results are interpreted will depend on the intended use of the masonry element being tested.
SCOPE
1.1 These test methods cover methods for determining the strength and load-deflection characteristics of masonry wall elements.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C901-18(Specification)
Standard Specification for Prefabricated Masonry Panels

ABSTRACT
This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Structural design of panels shall be performed in accordance with the provisions of the applicable local building code and the requirements specified. A quality control test shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Methods of prefabrication, field erection, and jointing are not covered in this specification.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1280-18(2023)(Specification)
Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing

ABSTRACT
This specification covers the minimum requirements for and the methods of application of gypsum sheathing for use as a substrate for exterior wall cladding. Gypsum sheathing board is a substrate that shall be covered by an exterior cladding or other weather-resistive barrier and is not intended for long-term exposure. Framing members shall be installed so that the surface will be in an even plane, unless otherwise specified, after the gypsum sheathing has been applied. The gypsum sheathing shall be cut by scoring and breaking or by sawing, working from the face side. The cut edges and ends of gypsum sheathing shall be trimmed to obtain neat fitting joints when installed. Gypsum sheathing shall be fitted snugly around all window and door openings. Control joints, other accessories, and metal plaster base shall be fastened through gypsum sheathing to framing members. Where fire resistance or shear resistance is not required, and when metal lath and Portland cement plaster are to be applied as the exterior cladding over gypsum sheathing installed over framing members and the metal lath shall be installed after the gypsum sheathing, the gypsum sheathing shall be permitted to be applied and fastening of the gypsum sheathing shall be completed with the attachment of the self-furred metal lath.
SCOPE
1.1 This specification covers the minimum requirements for and methods of application of exterior gypsum panel products that are specifically designed for use as a substrate for exterior cladding.  
1.1.1 This specification does not cover gypsum panel products that are specifically designed for interior applications.  
1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction.  
1.3 Where sound control is required for a gypsum panel product assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s).  
1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction.  
1.4 Where resistance to racking loads or shear is required for a gypsum panel product assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s).  
1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3660-23(Specification)
Standard Consumer Safety Performance Specification for Motorized Partitions

SCOPE
1.1 This consumer safety performance specification establishes performance requirements, test methods, and labeling requirements for motorized partitions.  
1.2 Motorized partitions are used to provide flexibility in the size of spaces typically used for meetings, sports, recreational areas, schools, or social functions where children are often present.  
1.3 Motorized partitions include a motor to direct the opening and closing of the partition and are operated by trained individuals who control the on/off mechanism and opening and closing movement of the partition.  
1.4 The partition is made up of a series of rigid panels that move along a track.  
1.5 This specification does not include motorized curtains, elevator or garage doors, or non-motorized partitions.  
1.6 This specification shall be taken into consideration by owners/operators, architects, planners, engineers, equipment manufacturers, construction companies, construction contractors, and appropriate inspectors who may be involved in the design and construction of new facilities.  
1.7 This specification applies to the installation of new motorized partitions but may be useful for renovation projects such as updating older motorized partitions.  
1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2837-23(Test Method)
Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies

SIGNIFICANCE AND USE
5.1 This test method evaluates the following under the specified test conditions:  
5.1.1 The ability of a test specimen to undergo movement without reducing its fire resistance rating, and  
5.1.2 The duration for which a test specimen will contain a fire and retain its integrity during a predetermined fire resistive test exposure.  
5.2 This test method provides for the following measurements and evaluations where applicable:  
5.2.1 Ability of the test specimen  to movement cycle.  
5.2.2 Ability of the test specimen  to prohibit the passage of flames and hot gases.  
5.2.3 Transmission of heat through the test specimen.  
5.2.4 Ability of the test specimen  to resist the passage of water during a hose stream test.  
5.3 This test method does not provide the following:  
5.3.1 Any information about the rated wall assembly because its performance has already been determined.  
5.3.2 Evaluation of the degree by which the test specimen contributes to the fire hazard by generation of smoke, toxic gases, or other products of combustion.  
5.3.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the test specimen.  
5.3.4 Measurement of flame spread over the surface of the test specimen.
Note 3: The information in 5.3.1 – 5.3.4 may be determined by other suitable fire resistive test methods. For example, 5.3.4 may be determined by Test Method E84.  
5.4 In this procedure, the test specimens are subjected to one or more specific tests under laboratory conditions. When different test conditions are substituted or the end-use conditions are changed, it is not always possible by, or from, this test method to predict changes to the characteristics measured. Therefore, the results are valid only for the exposure conditions described in this test method.
SCOPE
1.1 This fire-test-response test method measures the performance of a unique fire resistive joint system called a continuity head-of-wall joint system, which is designed to be used between a rated wall assembly and a nonrated horizontal assembly during a fire resistance test.  
1.2 This fire-test-response standard does not measure the performance of the following:  
1.2.1 The rated wall assembly, which is already established by other test methods, such as Test Method E119, or  
1.2.2 The nonrated horizontal assembly, which would be established by other test methods such as Test Method E119.
Note 1: Typically, rated wall assemblies obtain a fire resistance rating after being tested to Test Method E119, NFPA 251, UL 263, CAN/ULC-S101, or other similar fire resistive test methods.  
1.3 This fire-test-response standard is not intended to evaluate the connections between rated wall assemblies and nonrated horizontal assemblies  unless part of the continuity head-of-wall joint system.  
1.4 The fire resistive test end point is the period of time elapsing before the first performance criteria is reached when the continuity head-of-wall joint system is subjected to one of two time-temperature fire exposures.  
1.5 The fire exposure conditions used are either those specified by Test Method E119 for testing assemblies to standard time-temperature exposures or Test Method E1529 for testing assemblies to rapid-temperature rise fires.  
1.6 This test method specifies the heating conditions, methods of test, and criteria to establish a fire resistance rating only for a continuity head-of-wall joint system.  
1.7 Test results establish the performance of continuity head-of-wall joint systems to maintain continuity of fire resistance of the rated wall assembly where the continuity head-of-wall joint system interfaces with a nonrated horizontal assembly during the fire-exposure period.  
1.8 Test results shall not be construed as having determined the continuity head-of-wall joint system, nonrated horizontal assembly and the rated wall assembly’s suitability for use after that ...

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    English language
    sale 15% off