iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3044-94(2006)

(Test Method)

Standard Test Method for Shear Modulus of Wood-Based Structural Panels

Standard Test Method for Shear Modulus of Wood-Based Structural Panels

SIGNIFICANCE AND USE
This test method is most useful for determining the moduli of rigidity of orthotropic materials for which moduli of rigidity cannot be computed from elastic moduli and Poisson’ratios. The shear modulus determined by this method appears in the equation governing the bending of a plate. This is the modulus that is needed in discussing the deflection and buckling of plates.
SCOPE
1.1 This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels. The grain direction or orientation of the individual plies, laminations, or layers shall be parallel or perpendicular to the edge of the test specimen. If the plies, laminations, or layers are of different material or elastic properties, the method gives the effective shearing modulus. Wood-based structural panels in use include plywood, waferboard, oriented strand board, and composites of veneer and of wood-based layers. Note 1—This test method is primarily designed for material in which the grain or orientation of the individual plies, laminations, or layers is parallel or perpendicular to the edge of the specimen. It may be used, however, for plywood specimens in which the grain is at 45 to the specimen edges if a four-ply panel with all plies of the same thickness is used. The controlling condition is that the EI (modulus of elasticity moment of inertia) values along both diagonals shall be equal.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2006
ICS
79.060.10 - Plywood
Technical Committee
D07 - Wood
Drafting Committee
D07.03 - Panel Products
Current Stage
Ref Project

Relations

Replaces
ASTM D3044-94(2000) - Standard Test Method for Shear Modulus of Wood-Based Structural Panels
Effective Date
01-Oct-2006
Replaced By
ASTM D3044-94(2011) - Standard Test Method for Shear Modulus of Wood-Based Structural Panels
Effective Date
01-Nov-2011

Buy Standard

ASTM D3044-94(2006) - Standard Test Method for Shear Modulus of Wood-Based Structural PanelsASTM D3044-94(2006) - Standard Test Method for Shear Modulus of Wood-Based Structural Panels
PreviousNext
Standard
ASTM D3044-94(2006) - Standard Test Method for Shear Modulus of Wood-Based Structural Panels
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3044 – 94 (Reapproved 2006)
Standard Test Method for
Shear Modulus of Wood-Based Structural Panels
This standard is issued under the fixed designation D3044; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope flexure of flat plates the deflections of the plate under this
loading is related to the shear modulus of the plate. Deflections
1.1 This test method covers determination of the shear
of the plate at points on the diagonal are measured relative to
modulus of wood-based structural panels associated with shear
its center. The shear modulus of the specimen is determined
distortion in the plane of the panels. The method is applicable
from load-deflection data. The shear modulus obtained is that
to all types of wood-based structural panels. The grain direc-
associated with shearing distortion in the plane of the plate. A
tion or orientation of the individual plies, laminations, or layers
photograph of testing apparatus and a deflection measuring
shall be parallel or perpendicular to the edge of the test
device is given in Fig. 1.
specimen. If the plies, laminations, or layers are of different
material or elastic properties, the method gives the effective
4. Significance and Use
shearing modulus. Wood-based structural panels in use include
4.1 This test method is most useful for determining the
plywood,waferboard,orientedstrandboard,andcompositesof
moduli of rigidity of orthotropic materials for which moduli of
veneer and of wood-based layers.
rigidity cannot be computed from elastic moduli and Poisson’s
NOTE 1—This test method is primarily designed for material in which
ratios. The shear modulus determined by this method appears
the grain or orientation of the individual plies, laminations, or layers is
in the equation governing the bending of a plate. This is the
parallel or perpendicular to the edge of the specimen. It may be used,
modulus that is needed in discussing the deflection and
however, for plywood specimens in which the grain is at 45° to the
buckling of plates.
specimen edges if a four-ply panel with all plies of the same thickness is
used. The controlling condition is that the EI (modulus of elastic-
5. Control of Moisture Content
ity 3 moment of inertia) values along both diagonals shall be equal.
5.1 The structural panel samples to be tested at specific
1.2 This standard does not purport to address all of the
moisture contents or equilibrium relative humidities shall be
safety concerns, if any, associated with its use. It is the
conditioned to approximately constant mass in controlled
responsibility of the user of this standard to establish appro-
atmospheric conditions. For approximating moisture condi-
priate safety and health practices and determine the applica-
tions of panels used under dry conditions, a relative humidity
bility of regulatory limitations prior to use.
of 65 6 2 % at a temperature of 68 6 6°F (206 3°C) is
2. Referenced Documents recommended. Specimens shall be tested without undue delay
after conditioning. Testing in similarly controlled atmosphere
2.1 ASTM Standards:
is recommended whenever possible.
D2395 Test Methods for Specific Gravity of Wood and
Wood-Based Materials
6. Test Specimen
D4442 Test Methods for Direct Moisture Content Measure-
6.1 The test specimen shall be square, with the thickness
ment of Wood and Wood-Base Materials
equal to the thickness of the material, and the length and width
3. Summary of Test Method not less than 25 nor more than 40 times the thickness. The
thickness, length, and width of each specimen shall be mea-
3.1 Thetestconsistsoftwistingasquareplateofmaterialby
sured to an accuracy of not less than6 0.3 %. Care shall be
applying loads at the ends of one diagonal and supporting the
taken to avoid obtaining test specimens with initial curvature.
plate at the ends of the other diagonal. From theory on the
7. Loading Procedure
This test method is under the jurisdiction of ASTM Committee D07 on Wood
7.1 Support the test specimen on supports having a radius of
and is the direct responsibility of Subcommittee D07.03 on Panel Products.
curvature not greater than ⁄4 in. (6 mm) on the opposite ends
Current edition approved Oct. 1, 2006. Published October 2006. Originally
of a plate diagonal, and loaded in a similar manner on the
approved in 1972. Last previous edition approved in 2000 as D3044 – 94 (2000).
DOI: 10.1520/D3044-94R06.
opposite ends of the other diagonal. In order that the loads are
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
applied at the corners, first attach metal plates as shown in Fig.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
1. Fig. 1 also shows suggested apparatus for applying load and
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D3044 – 94 (2006)
FIG. 1 Shear Modulus Test of Structural Panel Showing Method of Loading and Observing the Deflecti
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2718-24(Test Method)
Standard Test Methods for Structural Panels in Planar Shear (Rolling Shear)

SIGNIFICANCE AND USE
3.1 Planar shear (rolling shear) characteristics of structural panels determined by these test methods are essential for the rigorous design of various glued wood-panel structural components, such as box beams, folded plate roofs, and stressed skin panels. Planar shear also may govern the design at low span-depth ratios encountered in floors subjected to high concentrated loads, concrete forms at high pouring pressures, and bulk storage structures.  
3.2 The modulus of rigidity determined from Test Method A is a composite of the entire specimen acting as a unit. For plywood panels for which the ratio between the shear moduli of the plies with grain oriented parallel and perpendicular to the shear forces is known, the rolling shear modulus of the perpendicular plies can be calculated.  
3.3 Veneer produced by slicing or rotary peeling may contain fine checks or separations parallel to the grain on the knife side of the veneer that are produced as the knife is forced through the wood. These checks are termed “knife checks” to distinguish them from occasional checks that may be formed on the opposite side of the veneer by forces at the compression bar, and from checks caused by drying. Knife checks can have a significant effect on rolling shear properties in plywood panels and may be of significance in other veneer containing panels. Test Method A requires (when applicable) the testing of matching specimens having knife checks oriented both open and closed wherever possible (see Fig. 1).  
3.4 To control or define other variables influencing rolling shear, these test methods require determination of moisture content, specific gravity, and elapsed time-to-failure. Conditioning of test material in controlled atmospheres, determination of depth of knife checks (when applicable), and determination of percent of wood and plywood glueline failure (when applicable) are recommended.
SCOPE
1.1 These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined. Primarily, the tests measure the planar shear (rolling shear) strength developed in the plane of the panel.  
1.2 Structural panels in use include, but are not limited to, structural plywood, oriented strand board (OSB), and composites of veneer and of wood-based layers.  
1.3 Two test methods are included:  
1.3.1 Test Method A—Planar shear loaded by plates.  
1.3.2 Test Method B—Planar shear induced by five-point bending.  
1.3.3 The choice of method will be dictated by the purpose of the test and equipment available.  
1.3.4 Test Method A, Planar Shear Loaded by Plates—This test method uses a rectangular panel section adhered between steel plates with protruding knife edges to create load at the panel faces. This test method has been used to develop shear properties of plywood and oriented strand board for the purpose of confirming design values. This test method does not produce pure shear, but the specimen length is prescribed so that the secondary stresses have a minimum effect. The method determines shear strength and modulus of rigidity.  
1.3.5 Test Method B, Planar Shear Induced by Five-Point Bending—Planar shear stress is induced on the panel while loaded in bending using two continuous spans. This test method determines planar shear strength consistent with panel applications under transverse loading. This test method is able to determine shear strength at any moisture condition.  
1.4 The values stated in inch-pound units are to be regarded as standard. When there are values given in parentheses, these are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this stan...

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D3044-16(2023)(Test Method)
Standard Test Method for Shear Modulus of Wood-Based Structural Panels

SIGNIFICANCE AND USE
4.1 This test method is most useful for determining the moduli of rigidity of orthotropic materials for which moduli of rigidity cannot be computed from elastic moduli and Poisson's ratios. The shear modulus determined by this method appears in the equation governing the bending of a plate. This is the modulus that is needed in discussing the deflection and buckling of plates.
Note 2: Test Methods D2718 describes a plate method for determination of modulus of rigidity of structural panels.
SCOPE
1.1 This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels. The grain direction or orientation of the individual plies, laminations, or layers shall be parallel or perpendicular to the edge of the test specimen. If the plies, laminations, or layers are of different material or elastic properties, the method gives the effective shearing modulus. Wood-based structural panels in use include plywood, oriented strand board, and composites of veneer and of wood-based layers.  
Note 1: This test method is primarily designed for material in which the grain or orientation of the individual plies, laminations, or layers is parallel or perpendicular to the edge of the specimen. It may be used, however, for plywood specimens in which the grain is at 45° to the specimen edges if a four-ply panel with all plies of the same thickness is used. The controlling condition is that the EI (modulus of elasticity × moment of inertia) values along both diagonals shall be equal.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3500-20(Test Method)
Standard Test Methods for Wood Structural Panels in Tension

SIGNIFICANCE AND USE
3.1 These test methods determine the tensile properties of wood structural panels in response to stresses acting in the plane of the panel.  
3.2 Test Method A—This test method is suited to material that is uniform with respect to tensile properties. It is normally applied to wood structural panels and plywood of clear, straight-grained veneers. It may also be used to evaluate the strength of scarf and finger joints and other manufacturing process variables that can be expected to influence the tensile properties of wood structural panels in a uniform manner across the width of the sheet.  
3.3 Test Method B—This test method employs large test specimens and responds well to all manufacturing variables and growth characteristics that affect the tensile properties of wood structural panels.  
3.4 It is recommended that where comparisons are to be made that the same test method and specimen size be used throughout. This is because the volume of material included in a test specimen can influence the tensile strength regardless of whether the material properties are uniform throughout the sheet or vary widely due to the presence of growth or manufacturing features.
SCOPE
1.1 These test methods cover the determination of the tensile properties of wood structural panels.  
1.2 Wood structural panels in use include plywood, oriented strand board and composites of veneer, and other wood-based layers.  
1.3 Test Method A, Tensile Test for Small Specimens:  
1.3.1 This test method employs small specimens that should have a reduced cross section at the center of their length to avoid failure in the grip area. The transition from full width of specimen to reduced section at the center should be gradual to minimize stress concentration.  
1.3.2 When the measurements of elastic properties are to be made, the length of the reduced cross section at the center should be of sufficient length to accommodate an extensometer.  
1.4 Test Method B, Tensile Test for Large Specimens:  
1.4.1 This test method employs large specimens and responds well to manufacturing variables, panel grade characteristics, and other variables influencing the tensile properties of structural panels.  
1.4.2 The test specimens are large enough to contain the maximum sized grade characteristics found in panels. The test specimens have a constant cross section since the size and location of grade characteristics control the location of failures and the effect of stress concentration at the grips is overshadowed.  
1.4.3 This test method is recommended for the following:
1.4.3.1 Comparative tests of wood structural panels,
1.4.3.2 Determining the influence of any specific strength reducing variables on the tensile properties of wood structural panels,
1.4.3.3 Determination of tensile properties of panels for use in developing structural recommendations.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2719-19(Test Method)
Standard Test Methods for Wood Structural Panels in Shear Through-the-Thickness

SIGNIFICANCE AND USE
3.1 The strength and modulus of rigidity of wood structural panels in shear through-the-thickness obtained by these test methods are required for the rigorous design of many lumber-panel structural components such as trusses with panel gussets, box beams, folded plate roofs, and space plane structures, as well as floor and roof diaphragms, and shear walls. These properties are of secondary importance in typical roof deck and sheathing applications, and in crates and shipping containers.  
3.2 Veneer produced by slicing or rotary peeling may contain fine checks or separations parallel to the grain on the knife side of the veneer that are produced as the knife is forced through the wood. These checks are termed “knife checks” to distinguish them from occasional checks that may be formed on the opposite side of the veneer by forces at the compression bar, and from checks caused by drying. Average depth of knife checks has been found to strongly influence shear properties in plywood panels and may be of significance in veneer incorporated in composite panels. Measurement of depth of knife checks is recommended in these test methods.  
3.3 To control or define other variables influencing shear properties, these test methods require determination of moisture content and elapsed time to failure. The conditioning of test material in controlled atmosphere and determination of specific gravity are recommended.
SCOPE
1.1 These test methods determine the shear through-the-thickness properties of wood structural panels associated with shear distortion of the major axis. Wood structural panels in use include plywood, oriented strand board, and composites of veneer and of wood-based layers. Three test methods are included which differ somewhat in their application:    
Test Method  
Section  
A. Small Panel Shear Test  
5  
B. Large Panel Shear Test  
6  
C. Two-Rail Shear Test  
7
The choice of test method will be determined in part by the purpose of the tests, characteristics of test material, and equipment availability. In general, Test Method B or C for large specimens is preferred when equipment, amount of test material, and experimental plan permit.  
1.1.1 Test Method A: Small Panel Shear Test—This test method is suitable for testing small samples of uniform material including investigations of the effects of grain direction or orientation and of many raw materials and manufacturing process variables which influence shear properties uniformly throughout the specimen. The test method is unsuited for determining effects of grade and manufacturing features such as density variations, knots, and core gaps within the specimen.  
1.1.2 Test Method B: Large Panel Shear Test—This test method is regarded as giving the most accurate modulus of rigidity and is therefore recommended for elastic tests of materials to be used in stress analysis studies of test structures. This test method also yields excellent shear strength values for clear material. However, in spite of the large size of the specimen, failures generally occur only in narrow zones at the perimeter of the test area. This characteristic, a result of the heavy perimeter framing, causes this test method to be generally unsuited for determining grade and manufacturing effects such as density variations, core gaps, and knots that are not uniformly distributed throughout the panel. Generally, only in cases where effects of these factors under conditions of heavy perimeter framing are desired, should the test method be applied.  
1.1.3 Test Method C: Two-Rail Shear Test—This test method is applicable to a wide variety of materials and problems. The specimen fabrication and test procedures are somewhat simpler than in Test Methods A and B. The specimen is free to shear parallel to its 24-in. (610-mm) length dimension anywhere within the 8-in. (203-mm) width between rails. Thus, the test method is well suited for determining grade and...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D3499-19(Test Method)
Standard Test Method for Toughness of Wood Structural Panels

SIGNIFICANCE AND USE
3.1 The failure of wood-based materials with impact loads is sometimes an important criteria in design considerations. In addition, some effects on the mechanical properties of wood, such as decay, are best evaluated by measuring its toughness. This test method serves to evaluate the toughness of structural panel products while Methods D143 can be used to measure the toughness of solid clear wood specimens.
SCOPE
1.1 This test method for toughness of wood structural panels covers the determination of energy necessary to cause failure by impact loading of a beam specimen which is simply supported and loaded at midspan. Wood structural panels in use include plywood, oriented strand board, and composites of veneer and of wood-based layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1038-19(Terminology)
Standard Terminology Relating to Veneer, Plywood, and Wood Structural Panels
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D3501-05a(2018)(Test Method)
Standard Test Methods for Wood-Based Structural Panels in Compression

SIGNIFICANCE AND USE
3.1 These methods determine the compressive strength of structural panels in response to stresses acting in the plane of the panel.  
3.2 Method A—This method is applicable to structural panels of uniform properties within a panel. It is useful for evaluating plywood of clear, straight-grained veneers, and determining the effect of chemical or preservative treatments, construction, principal direction with respect to direction of stress, and other variables that are expected to uniformly influence the panel.  
3.3 Method B:  
3.3.1 The compressive properties obtained by this method are a reliable approximation of the strength of a full-size panel, and are intended for use in design.  
3.3.2 The compressive properties are influenced by buckling; however, this effect can be eliminated in this test by restraining the edges of the specimens.  
3.4 It is recommended that where comparisons are to be made, that the same method and specimen size be used throughout. This is because the volume of material included in a test specimen can influence the compressive strength regardless of whether the material properties are uniform throughout the sheet or vary widely due to the presence of growth or manufacturing features.
SCOPE
1.1 These test methods cover the determination of the compression properties of wood-based structural panels. Wood-based structural panels in use include plywood, waferboard, oriented strand board, and composites of veneer and of wood-based layers.  
1.2 Method A, Compression Test for Small Specimens—This method is applicable to small specimens that are uniform with respect to elastic and strength properties. Two types of compression tests are employed: one to evaluate both elastic and compressive strength properties, and the second to evaluate maximum compressive strength only.  
1.3 Method B, Compression Test for Large Specimens—This method employs large specimens and responds well to manufacturing variables and growth characteristics that influence compression properties of structural panels.  
1.3.1 This method is intended for the following:
1.3.1.1 Comparative tests of structural panels,
1.3.1.2 Evaluating the effects of moisture content on strength properties of structural panels,
1.3.1.3 Determining the strength properties of structural panels, and
1.3.1.4 Evaluating the effects of raw material and manufacturing variables on compression properties of structural panels.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2718-24(Test Method)
Standard Test Methods for Structural Panels in Planar Shear (Rolling Shear)

SIGNIFICANCE AND USE
3.1 Planar shear (rolling shear) characteristics of structural panels determined by these test methods are essential for the rigorous design of various glued wood-panel structural components, such as box beams, folded plate roofs, and stressed skin panels. Planar shear also may govern the design at low span-depth ratios encountered in floors subjected to high concentrated loads, concrete forms at high pouring pressures, and bulk storage structures.  
3.2 The modulus of rigidity determined from Test Method A is a composite of the entire specimen acting as a unit. For plywood panels for which the ratio between the shear moduli of the plies with grain oriented parallel and perpendicular to the shear forces is known, the rolling shear modulus of the perpendicular plies can be calculated.  
3.3 Veneer produced by slicing or rotary peeling may contain fine checks or separations parallel to the grain on the knife side of the veneer that are produced as the knife is forced through the wood. These checks are termed “knife checks” to distinguish them from occasional checks that may be formed on the opposite side of the veneer by forces at the compression bar, and from checks caused by drying. Knife checks can have a significant effect on rolling shear properties in plywood panels and may be of significance in other veneer containing panels. Test Method A requires (when applicable) the testing of matching specimens having knife checks oriented both open and closed wherever possible (see Fig. 1).  
3.4 To control or define other variables influencing rolling shear, these test methods require determination of moisture content, specific gravity, and elapsed time-to-failure. Conditioning of test material in controlled atmospheres, determination of depth of knife checks (when applicable), and determination of percent of wood and plywood glueline failure (when applicable) are recommended.
SCOPE
1.1 These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined. Primarily, the tests measure the planar shear (rolling shear) strength developed in the plane of the panel.  
1.2 Structural panels in use include, but are not limited to, structural plywood, oriented strand board (OSB), and composites of veneer and of wood-based layers.  
1.3 Two test methods are included:  
1.3.1 Test Method A—Planar shear loaded by plates.  
1.3.2 Test Method B—Planar shear induced by five-point bending.  
1.3.3 The choice of method will be dictated by the purpose of the test and equipment available.  
1.3.4 Test Method A, Planar Shear Loaded by Plates—This test method uses a rectangular panel section adhered between steel plates with protruding knife edges to create load at the panel faces. This test method has been used to develop shear properties of plywood and oriented strand board for the purpose of confirming design values. This test method does not produce pure shear, but the specimen length is prescribed so that the secondary stresses have a minimum effect. The method determines shear strength and modulus of rigidity.  
1.3.5 Test Method B, Planar Shear Induced by Five-Point Bending—Planar shear stress is induced on the panel while loaded in bending using two continuous spans. This test method determines planar shear strength consistent with panel applications under transverse loading. This test method is able to determine shear strength at any moisture condition.  
1.4 The values stated in inch-pound units are to be regarded as standard. When there are values given in parentheses, these are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this stan...

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D3044-16(2023)(Test Method)
Standard Test Method for Shear Modulus of Wood-Based Structural Panels

SIGNIFICANCE AND USE
4.1 This test method is most useful for determining the moduli of rigidity of orthotropic materials for which moduli of rigidity cannot be computed from elastic moduli and Poisson's ratios. The shear modulus determined by this method appears in the equation governing the bending of a plate. This is the modulus that is needed in discussing the deflection and buckling of plates.
Note 2: Test Methods D2718 describes a plate method for determination of modulus of rigidity of structural panels.
SCOPE
1.1 This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels. The grain direction or orientation of the individual plies, laminations, or layers shall be parallel or perpendicular to the edge of the test specimen. If the plies, laminations, or layers are of different material or elastic properties, the method gives the effective shearing modulus. Wood-based structural panels in use include plywood, oriented strand board, and composites of veneer and of wood-based layers.  
Note 1: This test method is primarily designed for material in which the grain or orientation of the individual plies, laminations, or layers is parallel or perpendicular to the edge of the specimen. It may be used, however, for plywood specimens in which the grain is at 45° to the specimen edges if a four-ply panel with all plies of the same thickness is used. The controlling condition is that the EI (modulus of elasticity × moment of inertia) values along both diagonals shall be equal.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3500-20(Test Method)
Standard Test Methods for Wood Structural Panels in Tension

SIGNIFICANCE AND USE
3.1 These test methods determine the tensile properties of wood structural panels in response to stresses acting in the plane of the panel.  
3.2 Test Method A—This test method is suited to material that is uniform with respect to tensile properties. It is normally applied to wood structural panels and plywood of clear, straight-grained veneers. It may also be used to evaluate the strength of scarf and finger joints and other manufacturing process variables that can be expected to influence the tensile properties of wood structural panels in a uniform manner across the width of the sheet.  
3.3 Test Method B—This test method employs large test specimens and responds well to all manufacturing variables and growth characteristics that affect the tensile properties of wood structural panels.  
3.4 It is recommended that where comparisons are to be made that the same test method and specimen size be used throughout. This is because the volume of material included in a test specimen can influence the tensile strength regardless of whether the material properties are uniform throughout the sheet or vary widely due to the presence of growth or manufacturing features.
SCOPE
1.1 These test methods cover the determination of the tensile properties of wood structural panels.  
1.2 Wood structural panels in use include plywood, oriented strand board and composites of veneer, and other wood-based layers.  
1.3 Test Method A, Tensile Test for Small Specimens:  
1.3.1 This test method employs small specimens that should have a reduced cross section at the center of their length to avoid failure in the grip area. The transition from full width of specimen to reduced section at the center should be gradual to minimize stress concentration.  
1.3.2 When the measurements of elastic properties are to be made, the length of the reduced cross section at the center should be of sufficient length to accommodate an extensometer.  
1.4 Test Method B, Tensile Test for Large Specimens:  
1.4.1 This test method employs large specimens and responds well to manufacturing variables, panel grade characteristics, and other variables influencing the tensile properties of structural panels.  
1.4.2 The test specimens are large enough to contain the maximum sized grade characteristics found in panels. The test specimens have a constant cross section since the size and location of grade characteristics control the location of failures and the effect of stress concentration at the grips is overshadowed.  
1.4.3 This test method is recommended for the following:
1.4.3.1 Comparative tests of wood structural panels,
1.4.3.2 Determining the influence of any specific strength reducing variables on the tensile properties of wood structural panels,
1.4.3.3 Determination of tensile properties of panels for use in developing structural recommendations.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off