ASTM D7589-13
(Test Method)Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine
Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref >
SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
5.2.1 Specification D4485.
5.2.2 API 1509.
5.2.3 SAE Classification J304.
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This test method is arranged as follows:
Subject
Section
Introduction
Scope
1
Referenced Documents
2
Terminology
3
Summary of Test Method
4
Significance and Use
5
Apparatus
6
General
6.1
Test Engine Configuration
6.2
Laboratory Ambient Conditions
6.3
Engine Speed and Torque Control
6.4
Dynamometer
6.4.1
Dynamometer Torque
6.4.2
Engine Cooling System
6.5
External Oil System
6.6
Fuel System
6.7
Fuel Flow Measurement
6.7.2
Fuel Temperature and Pressure Control to the Fuel
Flowmeter
6.7.3
Fuel Temperature and Pressure Control to Engine Fuel Rail
6.7.4
Fuel Supply Pumps
6.7.5
Fuel Filtering
6.7.6
Engine Intake Air Supply
6.8
Intake Air Humidity
6.8.1
Intake Air Filtration
6.8.2
Intake Air Pressure Relief
6.8.3
Temperature Measurement
6.9
Thermocouple Location
6.9.5
AFR Determination
6.10
Exhaust and Exhaust Back Pressure Systems
6.11
Exhaust Manifolds
6.11.1
Laboratory Exhaust System
6.11.2
Exhaust Back Pressure
6.11.3
Pressure Measurement and Pressure Sensor Locations
6.12
Engine Oil
6.12.2
Fuel to Fuel Flowmeter
6.12.3
Fuel to Engine Fuel Rail
6.12.4
Exhaust Back Pressure
6.12.5
Intake Air
6.12.6
Intake Manifold Vacuum/Absolute Pressure
6.12.7
Coolant Flow Differential Pressure
6.12.8
Crankcase Pressure
6.12.9
Engine Hardware and Related Apparatus
6.13
Test Engine Configuration
6.13.1
ECU (Power Control Module)
6.13.2
Thermostat Block-Off Adapter Plate
6.13.3
Wiring Harness
6.13.4
Oil Pan
6.13.5
Engine Water Pump Adapt...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7589 − 13
StandardTest Method for
Measurement of Effects of Automotive Engine Oils on Fuel
Economy of Passenger Cars and Light-Duty Trucks in
1,2
Sequence VID Spark Ignition Engine
This standard is issued under the fixed designation D7589; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This test method can be used by any properly equipped laboratory without outside assistance.
3
However, the ASTM Test Monitoring Center (TMC) provides reference oils and assessment of the
test results obtained on those oils by the laboratory (see AnnexA1). By this means, the laboratory will
know whether their use of this test method gives results statistically similar to those obtained by other
laboratories. Furthermore, various agencies require that a laboratory utilize the TMC services in
seeking qualification of oils against specifications. For example, the American Petroleum Institute
(API) imposes such a requirement, in connection with several U.S. Army engine lubricating oil
specifications. Accordingly, this test method is written for use by laboratories that utilize the TMC
services. Laboratories that choose not to use those services may simply ignore those portions of this
test method that refer to theTMC.This test method may be modified by means of Information Letters
issued by the TMC. In addition, the TMC may issue supplementary memoranda related to this test
method. Users of this test method shall contact the TMC,Attention:Administrator, to obtain the most
recent of these information letters.
1. Scope* 1.2.1 Exceptions—Where there is no direct equivalent such
as the units for screw threads, National Pipe threads/diameters,
1.1 This test method covers an engine test procedure for the
tubing size, and single source supply equipment specifications.
measurement of the effects of automotive engine oils on the
Additionally, Brake Fuel Consumption (BSFC) is measured in
fuel economy of passenger cars and light-duty trucks with
kilograms per kilowatthour.
gross vehicle weight 3856 kg or less. The tests are conducted
using a specified spark-ignition engine with a displacement of 1.3 This standard does not purport to address all of the
4
3.6 L (General Motors) on a dynamometer test stand. It safety concerns, if any, associated with its use. It is the
applies to multi viscosity grade oils used in these applications. responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.2 The values stated in SI units are to be regarded as
bility of regulatory limitations prior to use.
standard. No other units of measurement are included in this
1.4 This test method is arranged as follows:
standard.
Subject Section
Introduction
1
This test method is under the jurisdiction of ASTM Committee D02 on
Scope 1
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
Referenced Documents 2
D02.B0.10 on Standards Acceleration.
Terminology 3
Current edition approved May 1, 2013. Published June 2013. Originally
Summary of Test Method 4
approved in 2009. Last previous edition approved in 2012 as D7589 – 12a.
Significance and Use 5
DOI:10.1520/D7589-13.
Apparatus 6
2
The multi-cylinder engine test sequences were originally developed by an
General 6.1
ASTM Committee D02 group. Subsequently, the procedures were published in an
Test Engine Configuration 6.2
ASTM special technical publication. The Sequence VIB was published as Research Laboratory Ambient Conditions 6.3
Report RR:D02-1469, dated April 8, 1999. Engine Speed and Torque Control 6.4
3
Dynamometer 6.4.1
The ASTM Test Monitoring Center will update changes in this test method by
Dynamometer Torque 6.4.2
means of Information Letters. This edition includes all information letters through
Engine Cooling System 6.5
No. 12-3. Information letters may be obtained from the ASTM Test Monitoring
External Oil System 6.6
Center, 6555 Penn Avenue, Pittsburgh, PA 15206-4489, Attention: Administrator.
4
Fuel System 6.7
Trademark of General Motors Corporation, 300 Renaissance Center, Detroit,
Fuel Flow Measurement 6.7.2
MI 48265.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7589 − 13
Subject Section Subject Section
Fuel Temperature and Pressure Control to the Fuel 6.7.3 Thermocouple and Temperature Measurement System 10.2.6
Flowmeter Humidity Measurement System 10.2.7
Fuel Temperature and Pressu
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7589 − 12a D7589 − 13
Standard Test Method for
Measurement of Effects of Automotive Engine Oils on Fuel
Economy of Passenger Cars and Light-Duty Trucks in
1,2
Sequence VID Spark Ignition Engine
This standard is issued under the fixed designation D7589; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This test method can be used by any properly equipped laboratory without outside assistance.
3
However, the ASTM Test Monitoring Center (TMC) provides reference oils and assessment of the
test results obtained on those oils by the laboratory (see Annex A1). By this means, the laboratory will
know whether their use of this test method gives results statistically similar to those obtained by other
laboratories. Furthermore, various agencies require that a laboratory utilize the TMC services in
seeking qualification of oils against specifications. For example, the American Petroleum Institute
(API) imposes such a requirement, in connection with several U.S. Army engine lubricating oil
specifications. Accordingly, this test method is written for use by laboratories that utilize the TMC
services. Laboratories that choose not to use those services may simply ignore those portions of this
test method that refer to the TMC. This test method may be modified by means of Information Letters
issued by the TMC. In addition, the TMC may issue supplementary memoranda related to this test
method. Users of this test method shall contact the TMC, Attention: Administrator, to obtain the most
recent of these information letters.
1. Scope*
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel
economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a
4
specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi
viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters,
tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in
kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 This test method is arranged as follows:
Subject Section
Introduction
Scope 1
Referenced Documents 2
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.B0.10
on Standards Acceleration.
Current edition approved Nov. 1, 2012May 1, 2013. Published January 2013June 2013. Originally approved in 2009. Last previous edition approved in 2012 as
D7589D7589 – 12a.–12. DOI:10.1520/D7589-12A. DOI:10.1520/D7589-13.
2
The multi-cylinder engine test sequences were originally developed by an ASTM Committee D02 group. Subsequently, the procedures were published in an ASTM
special technical publication. The Sequence VIB was published as Research Report RR:D02-1469, dated April 8, 1999.
3
The ASTM Test Monitoring Center will update changes in this test method by means of Information Letters. This edition includes all information letters through No.
12-1.12-3. Information letters may be obtained from the ASTM Test Monitoring Center, 6555 Penn Avenue, Pittsburgh, PA 15206-4489, Attention: Administrator.
4
Trademark of General Motors Corporation, 300 Renaissance Center, Detroit, MI 48265.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7589 − 13
Subject Section
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
General 6.1
Test Engine Configuration 6.2
Laboratory Ambient Conditions 6.3
Engine Speed and T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.