D02.B0.10 - Standards Acceleration

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel  
...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine W...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VIF test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatt-hour.  
1.3 This test method is arranged as follows:    
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel Flow Meter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flow meter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapter Plate  
6.13.6  
Thermostat Block-Off Plate  
6.13.7  
Oil Filter Adapter Plate  
6.13.8  
Modified Throttle Body Assembly  
6.13.9  
Fuel Rail  
6.13.10  
Miscellaneous Apparatus Related to Engine Operation  
6.14  
Reagents and Materials  
7  
Engine Oil  
7.1  
Test Fuel ...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapte...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapte...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapte...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapt...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapt...

SIGNIFICANCE AND USE
5.1 Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.  
5.2 Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:  
5.2.1 Specification D4485.  
5.2.2 API 1509.  
5.2.3 SAE Classification J304.  
5.2.4 SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This test method is arranged as follows:    
Subject  
Section  
Introduction  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
General  
6.1  
Test Engine Configuration  
6.2  
Laboratory Ambient Conditions  
6.3  
Engine Speed and Torque Control  
6.4  
Dynamometer  
6.4.1  
Dynamometer Torque  
6.4.2  
Engine Cooling System  
6.5  
External Oil System  
6.6  
Fuel System  
6.7  
Fuel Flow Measurement  
6.7.2  
Fuel Temperature and Pressure Control to the Fuel
Flowmeter  
6.7.3  
Fuel Temperature and Pressure Control to Engine Fuel Rail  
6.7.4  
Fuel Supply Pumps  
6.7.5  
Fuel Filtering  
6.7.6  
Engine Intake Air Supply  
6.8  
Intake Air Humidity  
6.8.1  
Intake Air Filtration  
6.8.2  
Intake Air Pressure Relief  
6.8.3  
Temperature Measurement  
6.9  
Thermocouple Location  
6.9.5  
AFR Determination  
6.10  
Exhaust and Exhaust Back Pressure Systems  
6.11  
Exhaust Manifolds  
6.11.1  
Laboratory Exhaust System  
6.11.2  
Exhaust Back Pressure  
6.11.3  
Pressure Measurement and Pressure Sensor Locations  
6.12  
Engine Oil  
6.12.2  
Fuel to Fuel Flowmeter  
6.12.3  
Fuel to Engine Fuel Rail  
6.12.4  
Exhaust Back Pressure  
6.12.5  
Intake Air  
6.12.6  
Intake Manifold Vacuum/Absolute Pressure  
6.12.7  
Coolant Flow Differential Pressure  
6.12.8  
Crankcase Pressure  
6.12.9  
Engine Hardware and Related Apparatus  
6.13  
Test Engine Configuration  
6.13.1  
ECU (Power Control Module)  
6.13.2  
Thermostat Block-Off Adapter Plate  
6.13.3  
Wiring Harness  
6.13.4  
Oil Pan  
6.13.5  
Engine Water Pump Adapt...

SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API 1509.
SAE Classification J304.
SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This test method is arranged as follows: SubjectSection Introduction Scope1 Referenced Documents2 Terminology3 Summary of Test Method4 Significance and Use5 Apparatus6 General6.1 Test Engine Configuration6.2 Laboratory Ambient Conditions6.3 Engine Speed and Torque Control6.4 Dynamometer6.4.1 Dynamometer Torque6.4.2 Engine Cooling System6.5 External Oil System6.6 Fuel System6.7 Fuel Flow Measurement6.7.2 Fuel Temperature and Pressure Control to the Fuel
Flowmeter6.7.3 Fuel Temperature and Pressure Control to Engine Fuel Rail6.7.4 Fuel Supply Pumps6.7.5 Fuel Filtering6.7.6 Engine Intake Air Supply6.8 Intake Air Humidity6.8.1 Intake Air Filtration6.8.2 Intake Air Pressure Relief6.8.3 Temperature Measurement6.9 Thermocouple Location6.9.5 AFR Determination6.10 Exhaust and Exhaust Back Pressure Systems6.11 Exhaust Manifolds6.11.1 Laboratory Exhaust System6.11.2 Exhaust Back Pressure6.11.3 Pressure Measurement and Pressure Sensor Locations6.12 Engine Oil6.12.2 Fuel to Fuel Flowmeter6.12.3 Fuel to Engine Fuel Rail6.12.4 Exhaust Back Pressure6.12.5 Intake Air6.12.6 Intake Manifold Vacuum/Absolute Pressure6.12.7 Coolant Flow Differential Pressure6.12.8 Crankcase Pressure6.12.9 Engine Hardware and Related Apparatus6.13 Test Engine Configuration6.13.1 ECU (Power Control Module)6.13.2 Thermostat Block-Off Adapter Plate6.13.3 Wiring Harness6.13.4 Oil Pan6.13.5 Engine Water Pump Adapter Plate6.13.6 Thermostat Block-Off Plate6.13.7 Oil Filter Adapter Plate6.13.8 Modified Throttle Body Assembly6.13.9 Fuel Rail6.13.10 Miscellaneous Apparatus Related to Engine Operation6.14 Reagents and Materials7 Engine Oil7.1 Test Fuel7.2 Engine Coolant7.3 Cleaning Materials7.4 Preparation of Apparatus8 Test Stand Preparation8.2 Engine Preparation9 Cleaning of Engine Parts9.3 Engine Assembly Procedure9.4 General Assembly Instruct...

SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API 1509.
SAE Classification J304.
SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API 1509.
SAE Classification J304.
SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API 1509.
SAE Classification J304.
SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Test Method—The data obtained from the use of this test method provide a comparative index of the fuel-saving capabilities of automotive engine oils under repeatable laboratory conditions. A BL has been established for this test to provide a standard against which all other oils can be compared. The BL oil is an SAE 20W-30 grade fully formulated lubricant. The test procedure was not designed to give a precise estimate of the difference between two test oils without adequate replication. The test method was developed to compare the test oil to the BL oil. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.
Use—The Sequence VID test method is useful for engine oil fuel economy specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
Specification D4485.
API 1509.
SAE Classification J304.
SAE Classification J1423.
SCOPE
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors) on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.