iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6183-00(2010)

(Test Method)

Standard Test Method for Tackiness of Finish on Leather

Standard Test Method for Tackiness of Finish on Leather

SIGNIFICANCE AND USE
This test method is intended for use on any type of finished leather.
This test will give an indication of the tackiness of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate the tendency of cloth to adhere to it. This test method does not apply to wet blue.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2010
ICS
59.140.10 - Processes and auxiliary materials
Technical Committee
D31 - Leather
Drafting Committee
D31.07 - Physical Properties
Current Stage
Ref Project

Relations

Replaces
ASTM D6183-00(2005) - Standard Test Method for Tackiness of Finish on Leather
Effective Date
01-Oct-2010

Buy Standard

ASTM D6183-00(2010) - Standard Test Method for Tackiness of Finish on LeatherASTM D6183-00(2010) - Standard Test Method for Tackiness of Finish on Leather
PreviousNext
Standard
ASTM D6183-00(2010) - Standard Test Method for Tackiness of Finish on Leather
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6183 − 00(Reapproved 2010)
Standard Test Method for
Tackiness of Finish on Leather
This standard is issued under the fixed designation D6183; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 5. Significance and Use
1.1 This test method is intended for use on finished leather 5.1 This test method is intended for use on any type of
to evaluate the tendency of cloth to adhere to it. This test finished leather.
method does not apply to wet blue.
5.2 This test will give an indication of the tackiness of the
1.2 This standard does not purport to address all of the
finish on leather.
safety concerns, if any, associated with its use. It is the
6. Apparatus
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica- 6.1 A circulating oven capable of maintaining 50 6 2°C
bility of regulatory limitations prior to use. (122 6 3.6°F).
6.2 A piece of bleached cheesecloth measuring at least 10
2. Referenced Documents
by 10 cm (3.94 by 3.94 in.).
2.1 ASTM Standards:
6.3 A suitable device for maintaining a pressure of 100
D1517 Terminology Relating to Leather 2 2
g/cm (1.42 lb/in. ) over the entire surface of the cheesecloth.
D1610 Practice for Conditioning Leather and Leather Prod-
7. Sampling, Test Specimens, and Test Units
ucts for Testing
D2813 Practice for Sampling Leather for Physical and
7.1 Sample leather according to Practice D2813.
Chemical Tests
7.2 The leather sample shall be larger than the cheesecloth.
3. Terminology
8. Conditioning
3.1 Definitions of terms used in this test method can be
8.1 Prepare the test pieces according to Practice D1610.
found in Terminology D1517.
8.2 Conditioning, other than as prescribed, shall be docu-
3.2 Definitions of Terms Specific to This Standard:
mented in the results.
3.2.1 tackiness, adj—the tendency of cloth to adhere to
9. Procedure
leather.
9.1 The finished leather specimen, the cheesecloth, and the
4. Summary of Test Method
device for maintaining pressure shall be placed in the oven
separately and brought to the required temperature.
4.1 Finished leather is brought into contact with a test cloth
under a prescribed pressure. The apparatus is heated for a
9.2 Apply the cheesecloth to the surface of the leather.
prescribed time, then cooled to room temperature. The cloth
Apply and maintain a pressure of 100 g/cm evenly over the
subsequently is peeled from the finished leather while observ-
surface of the cheesecloth for 5 min while remaining in the
ing the force to remove the cloth and deformation of the
oven.
finished leather surface.
9.3 Remove the pressure from the cheesecloth, and remove
the finished leather and cheesecloth while still in contact with
it from the oven.
This test method is under the jurisdiction ofASTM Committee D31 on Leather
and is the direct responsibility of Subcommittee D31.07 on Physical Properties.
9.4 Allow the finished leather and cheesecloth to cool under
Current edition approved Oct. 1, 2010. Published November 2010. Originally
conditions specified by Practice D1610.
approved in 1997. Last previous edition approved in 2005 as D6183 – 00 - (2005).
DOI: 10.1520/D6183-00R10.
9.5 Hold the test specimen vertically and at a distance of 20
Fo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3898-93(2023)(Test Method)
Standard Test Method for Chromic Oxide in Basic Chromium Tanning Liquors

SIGNIFICANCE AND USE
4.1 The procedure described is for the quality control for manufacturing liquors and specifications for the purchase of such liquors.  
4.2 The chromium content of the liquors determines the amount to be used to obtain the desired degree of tannage, and hence may be a matter for specification in the purchase of leather.
SCOPE
1.1 This test method covers the determination of chromic oxide in chrome tanning liquors, either simple, with added aluminum or zirconium, or with the usual masking complexing agents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4906-95(2023)(Test Method)
Standard Test Method for Total Solids and Ash Content in Leather Finishing Materials

SIGNIFICANCE AND USE
2.1 This test method is intended for use in determining the total solids content and the ash content of a finishing material before its use on any leather.
SCOPE
1.1 This test method covers the total solids and ash content of finishing materials.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6182-23(Test Method)
Standard Test Method for Flexibility and Adhesion of Finish on Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of finished leather.  
5.2 This test method will give an indication of the flexibility, adhesion, and strength of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate resistance to cracking, delamination, and discoloration of the finish when subjected to repeated flexing. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6183-00(2021)(Test Method)
Standard Test Method for Tackiness of Finish on Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of finished leather.  
5.2 This test will give an indication of the tackiness of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate the tendency of cloth to adhere to it. This test method does not apply to wet blue.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6656-16(2021)(Test Method)
Standard Test Method for Determination of Chromic Oxide in Wet Blue (Perchloric Acid Oxidation)

SIGNIFICANCE AND USE
5.1 The procedure described is specific for chromium in Wet Blue. Vanadium is the only common interfering element and is rarely present in quantity. The precision and accuracy of the methods are usually, at least, as good as the sampling of Wet Blue itself.  
5.2 The chromium content of Wet Blue is related to the degree of tannage obtained, and hence may be a matter for specification in the purchase of Wet Blue. The procedure described provides adequate accuracy for this purpose.
SCOPE
1.1 This test method covers the determination of chromic oxide in Wet Blue that has been partly or completely tanned with chromium compounds. In general, the samples will contain chromium content between 1 % and 5 % when calculated as chromic oxide expressed upon a dry basis otherwise referred to as moisture-free basis (mfb).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This test method does not apply to Wet White.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for specific safety hazards.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6657-16(2021)(Test Method)
Standard Test Method for pH of Wet Blue and Wet White

SIGNIFICANCE AND USE
4.1 This test method is designed to measure the pH of a distilled-water extract of Wet Blue and Wet White. This is considered to be a measure of the acidity or alkalinity of the Wet Blue or Wet White. Excessive acidity or alkalinity may have a deleterious effect on the aging characteristics of Wet Blue and Wet White and the leather made from it.  
4.2 This test method is suitable for development, control, and service evaluation of wet blue.
SCOPE
1.1 This test method covers the determination of the pH of all types of Wet Blue and Wet White.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6659-16(2021)(Practice)
Standard Practice for Sampling and Preparation of Wet Blue and Wet White for Physical and Chemical Tests

SIGNIFICANCE AND USE
4.1 The sampling procedures described in this practice have been designed to ensure random sampling of Wet Blue and Wet White for physical and chemical tests. Wet Blue and Wet White are natural products and as such are subject to extensive variability. The physical and chemical properties vary considerably depending on location on the hide, side, or skin from which the test sample is taken. Random sampling of specimens from a predefined location and orientation minimizes test bias and variability. This practice defines these parameters.
SCOPE
1.1 This practice covers the sampling and preparation of Wet Blue and Wet White for physical and chemical tests. The product is grouped into lots that are randomly sampled in such a manner as to produce a representative sample of the lot. This sample may be used to determine compliance of the lot with applicable specification requirements, and on the basis of results, the lot may be accepted or rejected in its entirety.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4900-99(2020)(Test Method)
Standard Test Method for Lignosulfonates (Sulfite Cellulose) in Tanning Extracts

SIGNIFICANCE AND USE
4.1 This test method is useful to detect possible adulteration of tanning material extract with cheap and inferior lignosulfonates.
SCOPE
1.1 This test method is intended for use in detecting the presence of lignosulfonates (sulfite cellulose) in extracts of tanning materials.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6402-99(2020)(Test Method)
Standard Test Method for Determining Soluble Solids and Insolubles in Extracts of Vegetable Tanning Materials

SIGNIFICANCE AND USE
5.1 This test method is used to determine the proportion of the total solids which are soluble solids and that proportion which are insoluble solids in a solution of tannin extract or in the water extract from raw or spent materials prepared for tannin analysis.  
5.2 The specimens are aliquots from the analytical solutions prepared from tannin extracts or the water extract solutions prepared from raw or spent materials.  
5.3 The soluble solids are defined as the portion of the total solids which are dissolved in the water and pass through a filter prepared by depositing a layer of Kaolin paste onto a standard filter paper.  
5.4 The insolubles are defined as the portion of the total solids which do not pass through the standard filter paper prepared with the layer of Kaolin paste.  
5.5 The results of this test method are dependent on a great many variables but particularly upon:  
5.5.1 The temperature conditions under which the solutions were prepared and stored and the temperature at which the current analysis is performed;  
5.5.2 The uniformity and consistency of the Kaolin paste layer deposited onto the filter paper;  
5.5.3 The rate of solution run-out from the pipette; etc. It is, therefore, essential that the method be followed exactly in order to obtain reproducible results both among specimens within a laboratory and for analyses between laboratories.
SCOPE
1.1 This test method is intended for use in determining the quantity of soluble solids and insolubles in solutions of tannin extracts, water extracts of vegetable tanning materials, or tanning liquors. This test method is applicable to the analysis of liquid, solid, pasty, and powdered tannin extracts and to the water extracts of raw or spent materials.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6409-99(2020)(Practice)
Standard Practice for Color Tests with Sheepskin Skiver

SIGNIFICANCE AND USE
5.1 This practice provides a standard procedure for comparing the color of leather tanned with different tanning extracts or mixtures of extracts or for monitoring the color consistency of tannery liquors.
SCOPE
1.1 This practice covers making color tests of all types of vegetable tanning extracts and of vegetable tanning materials to determine the color imparted to tanned skins.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off