iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3172-07a

(Practice)

Standard Practice for Proximate Analysis of Coal and Coke

Standard Practice for Proximate Analysis of Coal and Coke

SIGNIFICANCE AND USE
Test methods, as herein described, can be used to establish the rank of coals, show the ratio of combustible to incombustible constituents, provide the basis for buying and selling, and evaluate for beneficiation or for other purposes.
SCOPE
1.1 This practice covers the determination of moisture, volatile matter, and ash and the calculation of fixed carbon on coals and cokes sampled and prepared by prescribed methods and analyzed according to ASTM established procedures.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2007
ICS
75.160.10 - Solid fuels
Technical Committee
D05 - Coal and Coke
Drafting Committee
D05.21 - Methods of Analysis
Current Stage
Ref Project

Relations

Replaces
ASTM D3172-07 - Standard Practice for Proximate Analysis of Coal and Coke
Effective Date
01-Oct-2007
Referred By
ASTM D121-15 - Standard Terminology of Coal and Coke
Effective Date
01-Oct-2007
Referred By
ASTM D7569/D7569M-10(2015)e1 - Standard Practice for Determination of Gas Content of Coal—Direct Desorption Method
Effective Date
01-Oct-2007
Referred By
ASTM D3174-12(2018)e1 - Standard Test Method for Ash in the Analysis Sample of Coal and Coke from Coal
Effective Date
01-Oct-2007
Referred By
ASTM D1412/D1412M-20 - Standard Test Method for Equilibrium Moisture of Coal at 96 to 97 Percent Relative Humidity and 30 °C
Effective Date
01-Oct-2007
Referred By
ASTM D3176-15 - Standard Practice for Ultimate Analysis of Coal and Coke
Effective Date
01-Oct-2007
Referred By
ASTM D6700-19 - Standard Guide for Use of Scrap Tires as Tire-Derived Fuel
Effective Date
01-Oct-2007
Referred By
ASTM D388-23 - Standard Classification of Coals by Rank
Effective Date
01-Oct-2007
Referred By
ASTM E1131-20 - Standard Test Method for Compositional Analysis by Thermogravimetry
Effective Date
01-Oct-2007

Buy Standard

ASTM D3172-07a - Standard Practice for Proximate Analysis of Coal and CokeASTM D3172-07a - Standard Practice for Proximate Analysis of Coal and Coke
PreviousNext
Standard
ASTM D3172-07a - Standard Practice for Proximate Analysis of Coal and Coke
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3172 − 07a
StandardPractice for
1
Proximate Analysis of Coal and Coke
This standard is issued under the fixed designation D3172; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D6609 Guide for Part-Stream Sampling of Coal
D7256/D7256M Practice for Mechanical Collection and
1.1 This practice covers the determination of moisture,
Within-System Preparation of a Gross Sample of Coal
volatile matter, and ash and the calculation of fixed carbon on
3
from Moving Streams (Withdrawn 2008)
coals and cokes sampled and prepared by prescribed methods
and analyzed according to ASTM established procedures.
3. Terminology
1.2 This standard does not purport to address all of the
3.1 Definitions:
safety concerns, if any, associated with its use. It is the
3.1.1 proximate analysis of coal and coke—an assay of the
responsibility of the user of this standard to establish appro-
moisture, ash, volatile matter, and fixed carbon as determined
priate safety and health practices and determine the applica-
by prescribed methods. Other constituents such as sulfur and
bility of regulatory limitations prior to use.
phosphorus are not included.
2. Referenced Documents
2 4. Significance and Use
2.1 ASTM Standards:
D346 Practice for Collection and Preparation of Coke 4.1 Test methods, as herein described, can be used to
Samples for Laboratory Analysis establish the rank of coals, show the ratio of combustible to
D388 Classification of Coals by Rank incombustible constituents, provide the basis for buying and
D2013 Practice for Preparing Coal Samples for Analysis selling, and evaluate for beneficiation or for other purposes.
D2234/D2234M Practice for Collection of a Gross Sample
of Coal
5. Sampling
D3173 Test Method for Moisture in the Analysis Sample of
5.1 Coal sample collection shall be in accordance the
Coal and Coke
sampling section of Classification D388, if the proximate
D3174 Test Method for Ash in the Analysis Sample of Coal
analysis is to be used for classification of coal by rank. Other
and Coke from Coal
wise, coal sample collection shall be done in accordance with
D3175 Test Method for Volatile Matter in the Analysis
any of the following Guides or Practices as appropriate:
Sample of Coal and Coke
Guide D6609, Practice D4596, Practice D4916, Practice
D4596 Practice for Collection of Channel Samples of Coal
D5192, and Practice D6883. In all other cases, sample collec-
in a Mine
tion shall be in accordance with Practice D2234/D2234M.
D4916 PracticeforMechanicalAugerSampling(Withdrawn
3
5.2 Coke sampling shall be done in accordance with Prac-
2008)
tice D346.
D5192 Practice for Collection of Coal Samples from Core
D6883 Practice for Manual Sampling of Stationary Coal
6. Analysis Sample
from Railroad Cars, Barges, Trucks, or Stockpiles
6.1 For coal, sample preparations shall be in accordance
with Practices D2013 or D7256/D7256M. The analysis sample
1
This practice is under the jurisdiction of ASTM Committee D05 on Coal and
shall be the material pulverized to pass a 250-µm (No. 60 sieve
Coke and is the direct responsibility of Subcommittee D05.21 on Methods of
in accordance with Practice D2013.
Analysis.
Current edition approved Oct. 1, 2007. Published October 2007. Originally
6.2 For coke, sample preparations
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3402/D3402M-23(Test Method)
Standard Test Method for Tumbler Test for Coke

SIGNIFICANCE AND USE
4.1 Coke undergoes various degrees of degradation during removal from coke ovens, transportation, and its decent within a blast furnace to the combustion zone. These processes subject the coke to impact and abrasion. This test method is a relative measure of the resistance of coke to breakage when subjected to these degradation processes.
SCOPE
1.1 This test method describes a procedure for obtaining a relative measure of the resistance to degradation of coke by impact and abrasion.  
1.2 Standard Procedure—This procedure uses a coke sample that is sized to 75 mm by 50 mm [ 3.0 in. by 2 in.].  
1.3 Alternative Procedure—This procedure uses a composite coke sample that is comprised of coke sized 50 % of 63 mm by 50 mm [2.5 in. by 2 in.] and 50 % of 50 mm by 37.5 mm [2 in. by 1.50 in.].  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D388-23(Classification)
Standard Classification of Coals by Rank

ABSTRACT
This specification covers the classification of coals by rank, that is, according to their degree of metamorphism, or progressive alteration, in the natural series from lignite to anthracite. These coals are mainly composed of vitrinite. The classification shall be based on gradational properties that depend on the degree of metamorphism. The classification shall also be according to fixed carbon and gross calorific value calculated to the mineral-matter-free basis.
SIGNIFICANCE AND USE
4.1 This classification establishes categories of coal based on gradational properties that depend principally on the degree of metamorphism to which the coal was subjected while buried. These categories indicate ranges of physical and chemical characteristics that are useful in making broad estimates of the behavior of coal in mining, preparation, and use.
SCOPE
1.1 This standard covers the classification of coals by rank, that is, according to their degree of metamorphism, or progressive alteration, in the natural series from lignite to anthracite.  
1.2 This classification is applicable to coals that are composed mainly of vitrinite.  
Note 1: Coals rich in inertinite or liptinite (exinite), or both, cannot be properly classified because, in those macerals, the properties that determine rank (calorific value, volatile matter, and agglomerating character) differ greatly from those of vitrinite in the same coal. Often, such coals can be recognized by megascopic examination. In North America, these coals are mostly nonbanded varieties that contain only a small proportion of vitrain and consist mainly of attrital materials. The degree of metamorphism of nonbanded and other vitrinite-poor coals can be estimated by determining the classification properties of isolated or concentrated vitrinite fractions, or by determining the reflectance of the vitrinite (see Test Method D2798 and Appendix X1 of this classification). However, in the use of these vitrinite-poor coals, some properties normally associated with rank, such as rheology, combustibility, hardness, and grindability (as well as the rank determining properties) may differ substantially from those of vitrinite-rich coals of the same degree of metamorphism.  
1.3 The accuracy of the classification of impure coal may be impaired by the effect of large amounts of mineral matter on the determination of volatile matter and calorific value, and on their calculation to the mineral-matter-free basis.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4.1 Exception—The values stated in British thermal units per pound (Btu/lb) are to be regarded as the standard. The SI equivalents of Btu/lb are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D2639/D2639M-23(Test Method)
Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer

SIGNIFICANCE AND USE
5.1 Reliable values of the plastic properties of coals are used to predict or explain the behavior of a coal or blends during carbonization or in other processes such as gasification, liquefaction, and combustion.
SCOPE
1.1 This test method covers a relative measure of the plastic behavior of coal when heated under prescribed conditions. This test method may be used to obtain semiquantitative values of the plastic properties of coals and blends used in carbonization and in other situations where determination of plastic behavior of coals is of practical importance.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 In this test method, the term “mass” applies to measurements expressed with both SI units (for example, kg) and inch-pound units (for example, lb).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D3302/D3302M-22a(Test Method)
Standard Test Method for Total Moisture in Coal

SIGNIFICANCE AND USE
5.1 The collection and treatment of the sample as specified for the referee method is intended for the express purpose of determining the total moisture in coal. The standard is available to producers, sellers, and consumers as a method of determination when other techniques or modifications are not mutually agreed upon.  
5.2 The commercial method, which determines total moisture content of the crushed and divided sample, is designated as the method for total moisture for routine commercial practice.
SCOPE
1.1 This test method covers the measurement of the total moisture in coal as it exists at the site, at the time, and under the conditions it is sampled. It is applicable to coals as mined, processed, shipped, or used in normal commercial pursuits. It is not applicable to coal-water slurries, sludges, or pulverized products under 0.5 mm-diameter sieve size. It is applicable to coals of all ranks within the recognized limitations imposed by oxidation and decomposition characteristics of lower rank coals. Because of its empirical nature, strict adherence to basic principles and permissive procedures are required for valid results (see Appendix X1). This complete standard is available to producers, sellers, and consumers as a total moisture method when other procedures or modifications are not mutually agreed on.  
1.2 Since coal can vary from extremely wet (water-saturated) to completely dry, special emphasis must be placed on the sampling, sample preparation, and the moisture determination itself to ensure total reliability of measurement. Therefore, this standard entails collection of the gross sample, sample preparation, and the method of determination.  
1.3 While it is recognized that such a standard may be unwieldy for routine usage in commercial operations, it can provide a common base for agreement in cases of dispute or arbitration. The complete standard is referred to as the referee method. Embodied in the standard is the commercial method starting with the crushed and divided sample when the gross sample is not too wet to crush and divide. See Practice D2961/D2961M and Test Method D3173 for other moisture methods.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D7430/D7430M-22(Practice)
Standard Practice for Mechanical Sampling of Coal

SIGNIFICANCE AND USE
6.1 It is intended that this practice be used to provide a sample representative of the coal from which it is collected. Because of the variability of coal and the wide variety of mechanical sampling equipment available, caution should be used in all stages of the sample collection process, the design of sampling system specifications, the equipment procurement, and the acceptance testing of installed equipment.  
6.2 After removal from the sampling system and further preparation (Practice D2013/D2013M), the sample may be analyzed for a number of different parameters. These parameters may define the lot's value, its ability to meet specifications, its environmental impact, as well as other properties.
SCOPE
1.1 This practice is divided into four parts: A, B, C, and D. These four parts represent the previous Practices D7256/D7256M, D4916, D4702, and D6518. These four standards are the four that govern the mechanical sampling of coal and have been combined into one document for the ease of reference of the users of these standards.  
1.2 The scope of Part A can be found in Section 4.  
1.3 The scope of Part B can be found in Section 13.  
1.4 The scope of Part C can be found in Section 19.  
1.5 The scope of Part D can be found in Section 32.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 7, 16, 21, 35, and 38.1.1.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    47 pages
    English language
    sale 15% off
  • Standard
    47 pages
    English language
    sale 15% off
ASTM
ASTM D4606-21(Test Method)
Standard Test Method for Determination of Arsenic and Selenium in Coal by the Hydride Generation/Atomic Absorption Method

SIGNIFICANCE AND USE
4.1 This test method permits measurement of the total mass fraction of arsenic and selenium in coal for the purpose of evaluating these elements where they can be of concern, for example, in coal combustion. When coal samples are prepared for analysis in accordance with this test method, the arsenic and selenium are quantitatively retained and are representative of the total mass fraction in the coal.
SCOPE
1.1 This test method2 covers the determination of total arsenic in the range of 0.7 ug/g to 12 ug/g and selenium in the range of 0.6 ug/g to 5 ug/g in coal.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6357-21b(Test Method)
Standard Test Methods for Determination of Trace Elements in Coal, Coke, and Combustion Residues from Coal Utilization Processes by Inductively Coupled Plasma Atomic Emission Spectrometry, Inductively Coupled Plasma Mass Spectrometry, and Graphite Furnace Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 Coal contains several elements whose individual mass fractions are generally less than 0.01 %. These elements are commonly and collectively referred to as trace elements. These elements primarily occur as part of the mineral matter in coal. The potential release of certain trace elements from coal combustion sources has become an environmental concern.  
5.2 The ash prepared in accordance with these provisional test methods quantitatively retains the elements listed in 1.1 and is representative of their mass fractions in the coal or coke.
SCOPE
1.1 These test methods pertain to the determination of antimony, arsenic, beryllium, cadmium, chromium, cobalt, copper, lead, manganese, molybdenum, nickel, vanadium, and zinc in coal and coke. These test methods can also be used for the analysis of residues from coal combustion processes. Additionally, there are specific test methods outlined that pertain to the determination of rare earth elements in coal and coal combustion residues.
Note 1: These test methods may be applicable to the determination of other trace elements.
Note 2: Rare earth elements are understood to include: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, scandium, terbium, thulium, ytterbium, and yttrium.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.2.1 All percentages are percent mass fractions unless otherwise noted.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    English language
    sale 15% off
ASTM
ASTM D6349-21(Test Method)
Standard Test Method for Determination of Major and Minor Elements in Coal, Coke, and Solid Residues from Combustion of Coal and Coke by Inductively Coupled Plasma—Atomic Emission Spectrometry

SIGNIFICANCE AND USE
5.1 A compositional analysis of coal and coke and their associated combustion residues are often useful in assessing their quality. Knowledge of the elemental composition of the associated residues is also useful in predicting the elemental enrichment/depletion compositional behavior of ashes and slags in comparison to the mass fraction in the parent coal. Utilization of the ash by-products and hazardous potential may also depend on the chemical composition and leachability of the inorganic constituents of the coal ash.  
5.2 The chemical composition of laboratory-prepared ash may not exactly represent the composition of mineral matter in coal or the composition of fly ash and slag resulting from commerical-scale burning of the coal.
SCOPE
1.1 This test method covers a procedure for the analysis of the commonly determined major and minor elements in coal, coke, and solid residues from combustion of coal and coke. These residues may be laboratory ash, bottom ash, fly ash, flue gas desulfurization sludge, and other combustion process residues.
Note 1: There are two interlaboratory studies associated with this test method. The first was conducted in 1997 ( RR:D05-1035)2 and the second was conducted in 2007 ( RR:D05-1032).3 Sulfur trioxide was only included in the 2007 study, and that study only included combustion residues derived from ash and no combustion residues derived from coke.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D4326-21(Test Method)
Standard Test Method for Major and Minor Elements in Coal Ash By X-Ray Fluorescence

SIGNIFICANCE AND USE
5.1 A compositional analysis of ash is used in describing the quality of coal for its complete characterization. Ash composition is useful in predicting slagging and fouling characteristics of combusted materials as well as the potential utilization of ash by-products.  
5.2 The chemical composition of laboratory prepared coal ash is rarely, if ever, representative of the composition of the mineral matter in the coal because the ashing process can alter some minerals. However, it can approximate the composition of the fly ash and slag resulting from commercial combustion of coal.
SCOPE
1.1 This test method covers the analysis of the commonly determined major and minor elements in ash from coal using X-ray fluorescence (XRF) techniques.
Note 1: Test Method D5016 is used for determination of sulfur.
Note 2: Although not included in the present method, the determination of barium, strontium, and manganese may be required to yield adequate totals.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D167/D167M-21a(Test Method)
Standard Test Method for Apparent and True Specific Gravity and Porosity of Lump Coke

SIGNIFICANCE AND USE
4.1 Apparent and true specific gravity, as determined by this test method, are influenced by the type of coals carbonized and the operating and preparational conditions of that carbonization, that is, charge bulk density, heating rate, and pulverization level. In turn, these properties directly influence the performance in processes using coke.
SCOPE
1.1 This test method covers the determination of apparent specific gravity (Sections 5 to 9) and true specific gravity (Sections 10 to 14) of lump coke larger than 25 mm [1 in.] size and calculating porosity (Section 15) from the specific gravity data.  
1.2 Units—The values stated in either SI units or non-SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off