ASTM F2618-24
(Specification)Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems
Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems
SCOPE
1.1 This specification covers the performance requirements of CPVC pipe, fittings and solvent cements used in chemical waste drainage systems.
1.2 A system is made up of pipe, fittings and solvent cement that meet the requirements of this standard.
Note 1: Consult the manufacturer’s chemical resistance recommendations for chemical waste drainage applications prior to use.
1.3 The text of this specification references notes, footnotes and appendices that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The pressure tests described in this standard are laboratory hydrostatic tests that are intended to verify joint/system integrity. They are not intended for use as field tests of installed systems.
1.5 Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, no such testing shall be done unless the component manufacturer gives approval in writing.
Note 2: Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards should a system fail for any reason.
1.6 Mechanical joints used for joining pipe and fittings of different materials are provided for in this specification. They include common flanges, couplings, and unions.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 3: This specification specifies dimensional, performance, and test requirements for fluid handling applications but does not address venting of combustion gases.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2618 − 24 An American National Standard
Standard Specification for
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings
1
for Chemical Waste Drainage Systems
This standard is issued under the fixed designation F2618; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
1.1 This specification covers the performance requirements
mine the applicability of regulatory limitations prior to use.
of CPVC pipe, fittings and solvent cements used in chemical
1.9 This international standard was developed in accor-
waste drainage systems.
dance with internationally recognized principles on standard-
1.2 A system is made up of pipe, fittings and solvent cement
ization established in the Decision on Principles for the
that meet the requirements of this standard.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
NOTE 1—Consult the manufacturer’s chemical resistance recommenda-
tions for chemical waste drainage applications prior to use.
Barriers to Trade (TBT) Committee.
1.3 The text of this specification references notes, footnotes
2. Referenced Documents
and appendices that provide explanatory material. These notes
2
and footnotes (excluding those in tables and figures) shall not 2.1 ASTM Standards:
be considered as requirements of the specification. D543 Practices for Evaluating the Resistance of Plastics to
Chemical Reagents
1.4 The pressure tests described in this standard are labora-
D618 Practice for Conditioning Plastics for Testing
tory hydrostatic tests that are intended to verify joint/system
D1600 Terminology for Abbreviated Terms Relating to Plas-
integrity. They are not intended for use as field tests of installed
3
tics (Withdrawn 2024)
systems.
D1784 Classification System and Basis for Specification for
1.5 Due to inherent hazards associated with testing compo-
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
nents and systems with compressed air or other compressed
rinated Poly(Vinyl Chloride) (CPVC) Compounds
gases, no such testing shall be done unless the component
D2122 Test Method for Determining Dimensions of Ther-
manufacturer gives approval in writing.
moplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplas-
NOTE 2—Pressurized (compressed) air or other compressed gases
contain large amounts of stored energy, which present serious safety tic Pipe for Sewers and Other Gravity-Flow Applications
hazards should a system fail for any reason.
D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.6 Mechanical joints used for joining pipe and fittings of
different materials are provided for in this specification. They D2444 Practice for Determination of the Impact Resistance
of Thermoplastic Pipe and Fittings by Means of a Tup
include common flanges, couplings, and unions.
(Falling Weight)
1.7 The values stated in inch-pound units are to be regarded
D3311 Specification for Drain, Waste, and Vent (DWV)
as standard. The values given in parentheses are mathematical
Plastic Fittings Patterns
conversions to SI units that are provided for information only
F402 Practice for Safe Handling of Solvent Cements,
and are not considered standard.
Primers, and Cleaners Used for Joining Thermoplastic
NOTE 3—This specification specifies dimensional, performance, and
Pipe and Fittings
test requirements for fluid handling applications but does not address
venting of combustion gases.
F412 Terminology Relating to Plastic Piping Systems
F493 Specification for Solvent Cements for Chlorinated
1.8 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2024. Published April 2024. Originally the ASTM website.
3
approved in 2009. Last previous edition approved in 2021 as F2618–21. DOI: The last approved version
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2618 − 21 F2618 − 24 An American National Standard
Standard Specification for
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings
1
for Chemical Waste Drainage Systems
This standard is issued under the fixed designation F2618; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the performance requirements of CPVC pipe, fittings and solvent cements used in chemical waste
drainage systems.
1.2 A system is made up of pipe, fittings and solvent cement that meet the requirements of this standard.
NOTE 1—Consult the manufacturer’s chemical resistance recommendations for chemical waste drainage applications prior to use.
1.3 The text of this specification references notes, footnotes and appendices that provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The pressure tests described in this standard are laboratory hydrostatic tests that are intended to verify joint/system integrity.
They are not intended for use as field tests of installed systems.
1.5 Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, no
such testing shall be done unless the component manufacturer gives approval in writing.
NOTE 2—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards should
a system fail for any reason.
1.6 Mechanical joints used for joining pipe and fittings of different materials are provided for in this specification. They include
common flanges, couplings, and unions.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 3—This specification specifies dimensional, performance, and test requirements for fluid handling applications but does not address venting of
combustion gases.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved April 1, 2021April 1, 2024. Published April 2021April 2024. Originally approved in 2009. lastLast previous edition approved in 20192021 as
F2618–19. DOI: 10.1520/F2618-21–21. DOI: 10.1520/F2618-24
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2618 − 24
1.9 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D618 Practice for Conditioning Plastics for Testing
3
D1600 Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1784 Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.