ASTM B718-00(2016)

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Plate, Sheet, and Strip

ABSTRACT
This specification covers nickel-chromium-molybdenum-cobalt-tungsten-iron-silicon alloy (UNS N06333) plate, sheet, and strip intended for heat resisting applications and general corrosive services. Tension, Rockwell hardness, and Brinell hardness tests shall be performed on the material.
SCOPE
1.1 This specification covers wrought alloy UNS N06333 plate, sheet, and strip intended for heat resisting applications and general corrosive service.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2016
• ICS: 77.150.40 - Nickel and chromium products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B718 −00 (Reapproved 2016)
Standard Specification for
Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon
1
Alloy (UNS N06333) Plate, Sheet, and Strip
This standard is issued under the fixed designation B718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1473 Test Methods for Chemical Analysis of Nickel, Co-
balt and High-Temperature Alloys
1.1 This specification covers wrought alloy UNS N06333
plate, sheet, and strip intended for heat resisting applications
3. Terminology
and general corrosive service.
3.1 Definitions of Terms Specific to This Standard:
1.2 The values stated in inch-pound units are to be regarded
3
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in
as standard. The values given in parentheses are mathematical
thickness and over 10 in. (254) mm in width.
conversions to SI units that are provided for information only
3
and are not considered standard.
3.1.2 sheet, n—materialunder ⁄16in.(4.76mm)inthickness
and 24 in. (610 mm) and over in width.
1.3 This standard does not purport to address all of the
3
safety concerns, if any, associated with its use. It is the
3.1.3 strip, n—material under ⁄16 in. (4.76 mm) in thickness
responsibility of the user of this standard to become familiar
and under 24 in. (610 mm) in width.
with all hazards including those identified in the appropriate
Safety Data Sheet (SDS) for this product/material as provided
4. Ordering Information
by the manufacturer, to establish appropriate safety and health
4.1 It is the responsibility of the purchaser to specify all
practices, and determine the applicability of regulatory limi-
requirements that are necessary for the safe and satisfactory
tations prior to use.
performance of material ordered under this specification.
Examples of such requirements include but are not limited to
2. Referenced Documents
the following:
2
2.1 ASTM Standards:
4.1.1 Alloy name or UNS number.
B880 Specification for General Requirements for Chemical
4.1.2 Quantity.
Check Analysis Limits for Nickel, Nickel Alloys and
4.1.3 ASTM Designation and year of issue.
Cobalt Alloys
4.1.4 Form (plate, sheet, or strip).
E8 Test Methods for Tension Testing of Metallic Materials
4.1.5 Dimensions—Thickness, Width, and Length.
E10 Test Method for Brinell Hardness of Metallic Materials
4.1.6 Finish (Section 9).
E18 Test Methods for Rockwell Hardness of Metallic Ma-
4.1.7 Certification—State if certification is required (Sec-
terials
tion 16).
E29 Practice for Using Significant Digits in Test Data to
4.1.8 Samples for Product (Check) Analysis—State whether
Determine Conformance with Specifications
samples shall be furnished.
E140 Hardness Conversion Tables for Metals Relationship
4.1.9 Purchaser Inspection—If a purchaser wishes to wit-
Among Brinell Hardness, Vickers Hardness, Rockwell
ness tests or inspections of material at the place of
Hardness, Superficial Hardness, Knoop Hardness, Sclero-
manufacture, the purchase order must so state indicating which
scope Hardness, and Leeb Hardness
tests or inspections are to be witnessed.
1
This specification is under the jurisdiction of ASTM Committee B02 on
5. Materials and Manufacture
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
5.1 All material shall be furnished in the annealed condi-
Current edition approved June 1, 2016. Published June 2016. Originally
tion.
approved in 1983. Last previous edition approved in 2011 as B718 – 00 (2011).
DOI: 10.1520/B0718-00R16.
2
6. Chemical Requirements
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
6.1 The material shall conform to the requirements as to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. chemical composition specified in Table 1.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B718−00 (2016)
TABLE 1 Chemical Requirements TABLE 3 Thickness Tolerances for Hot-Rolled and Cold-Rolled
Sheets
Element Composition Limits, %
Tolerance Over and
Carbon 0.10 max
Specified Thickness, in. (mm)
Under, in. (mm)
Manganese 2.0 max
3
Phosphorus 0.03
Over 0.145 to less than ⁄16 (3.68 to less 0.014 (0.36)
Sulfur 0.03
than 4.76)
Silicon 1.5 max Over 0.130 to 0.145 (3.30 to 3.68), incl 0.012 (0.30)
Chromium 24.0–27.0
Over 0.114 to 0.130 (2.90 to 3.30), incl 0.010 (0.25)
Nickel 44.0–48.0
Over 0.098 to 0.114 (2.49
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B718 − 00 (Reapproved 2011) B718 − 00 (Reapproved 2016)
Standard Specification for
Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon
1
Alloy (UNS N06333) Plate, Sheet, and Strip
This standard is issued under the fixed designation B718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers wrought alloy UNS N06333 plate, sheet, and strip intended for heat resisting applications and
general corrosive service.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices,
and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness,
Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in thickness and over 10 in. (254) mm in width.
3
3.1.2 sheet, n—material under ⁄16 in. (4.76 mm) in thickness and 24 in. (610 mm) and over in width.
3
3.1.3 strip, n—material under ⁄16 in. (4.76 mm) in thickness and under 24 in. (610 mm) in width.
4. Ordering Information
4.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification. Examples of such requirements include but are not limited to the
following:
4.1.1 Alloy name or UNS number.
4.1.2 Quantity.
4.1.3 ASTM Designation and year of issue.
4.1.4 Form (plate, sheet, or strip).
4.1.5 Dimensions—Thickness, Width, and Length.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved June 1, 2011June 1, 2016. Published June 2011June 2016. Originally approved in 1983. Last previous edition approved in 20062011 as B718 – 00
(2006).(2011). DOI: 10.1520/B0718-00R11.10.1520/B0718-00R16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B718 − 00 (2016)
4.1.6 Finish (Section 9).
4.1.7 Certification—State if certification is required (Section 16).
4.1.8 Samples for Product (Check) Analysis—State whether samples shall be furnished.
4.1.9 Purchaser Inspection—If a purchaser wishes to witness tests or inspections of material at the place of manufacture, the
purchase order must so state indicating which tests or inspections are to be witnessed.
5. Materials and Manufacture
5.1 All material shall be furnished in the annealed condition.
6. Chemical Requirements
6.1 The material shall conform to the requirements as to chemical composition specified in Table 1.
6.2 If a product (check) analysis is performed by the purchaser, the material shall conform to the product (check) analysis
va
...