ASTM F707/F707M-94(2011)
(Specification)Standard Specification for Modular Gage Boards
Standard Specification for Modular Gage Boards
ABSTRACT
This specification covers modular gage boards for mounting dial pressure gages and dial thermometers for miscellaneous shipboard applications. Gage boards under this specification are suitable for pressure gages and dial thermometers with either turret or back flanged type cases and with either back or bottom connections. Gage boards may be furnished in two types and grades, namely: Type I, Type II, Grade a, and Grade b. Unless otherwise specified the gage boards shall be manufactured from the specified carbon steel for Grade a and form the specified aluminum alloy for Grade b. Materials shall be capable of being bent at room temperature through the prescribed angle and direction without cracking on the outside of the bent portion. Unless otherwise specified, gage boards shall be drilled for mounting the specified dial sizes. When specified, drilling shall be limited to one size gage for either Type I or Type II gage boards. The dimensional requirements for the gage boards are detailed and illustrated.
SCOPE
1.1 This specification covers modular gauge boards for mounting 89-mm (3½ -in.), 114-mm (4½-in.), 152-mm (6-in.), and 216-mm (8½ -in.) dial size pressure gauges and dial thermometers for miscellaneous shipboard applications.
1.2 Gauge boards ordered under this specification are suitable for pressure gauges and dial thermometers with either turret or back flanged type cases and with either back or bottom connections (see Appendix X1).
1.3 Gauge mounting dimensions shall be in accordance with ANSI B 40.01
1.4 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.
Note 1—Gauge boards covered by this specification are those normally supplied by the shipyard as opposed to the shipyard's equipment subcontractor.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F707/F707M −94 (Reapproved 2011) An American National Standard
Standard Specification for
Modular Gauge Boards
This standard is issued under the fixed designation F707/F707M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 3.1.2 Type II—Gauge boards for mounting 152-mm (6-in.)
and 216-mm (8 ⁄2-in.) dial size gauges as specified in Section
1.1 This specification covers modular gauge boards for
5.
1 1
mounting 89-mm (3 ⁄2-in.), 114-mm (4 ⁄2-in.), 152-mm (6-in.),
and 216-mm (8 ⁄2-in.) dial size pressure gauges and dial 3.2 Gauge boards are furnished in two grades as follows:
thermometers for miscellaneous shipboard applications. 3.2.1 Grade a—Gauge boards are to be manufactured from
carbon steel as specified in Section 5.
1.2 Gauge boards ordered under this specification are suit-
3.2.2 Grade b—Gauge boards are to be manufactured from
able for pressure gauges and dial thermometers with either
aluminum alloy as specified in Section 5.
turretorbackflangedtypecasesandwitheitherbackorbottom
connections (see Appendix X1).
4. Ordering Information
1.3 Gaugemountingdimensionsshallbeinaccordancewith
4.1 Orders for gauge boards under this specification shall
ANSI B 40.01.
include the following information:
4.1.1 Quantity (number of gauge boards),
1.4 The values stated in SI units are to be regarded as the
4.1.2 Name of item (gauge board),
standard. The inch-pound values given in parentheses are for
4.1.3 Type (Type I or Type II as specified by purchaser), see
information only.
3.1.1 and 3.1.2,
NOTE1—Gaugeboardscoveredbythisspecificationarethosenormally
4.1.4 Grade (Grade a or Grade b as specified by purchaser),
supplied by the shipyard as opposed to the shipyard’s equipment subcon-
see 3.2.1 and 3.2.2,
tractor.
4.1.5 Paint (as specified by purchaser), see 7.2,
2. Referenced Documents
4.1.6 Drilling for gauge mounting (as specified by
purchaser), see 5.1.1, and
2.1 Other Standards:
4.1.7 ASTM designation and date of issue.
B 40.1 Gauges, Pressure and Vacuum, Indicating Dial
Type—Elastic Element
5. Materials and Manufacture
Fed Spec. TT-P-645 Primer, Paint, Zinc-Chromate, Alkyd
3 5.1 Unless otherwise specified the gauge boards shall be
Type
manufactured from 11-gauge (manufacturers standard gauge)
DoD-P-15328 Primer (Wash), Pretreatment (Formula No.
3 carbon steel for Grade a and 3 mm ( ⁄8 in.) thick aluminum
117 for Metals) (Metric)
alloy for Grade b. Materials shall be capable of being bent at
room temperature through 90° in any direction to an inside
3. Classification
radius equal to its thickness without cracking on the outside of
3.1 Gauge boards are furnished in two types as follows:
the bent portion.
3.1.1 Type I—Gauge boards for mounting 89-mm (3 ⁄2-in.)
5.1.1 Unless otherwise specified, Type I gauge boards shall
and114-mm(4 ⁄2-in.)dialsizegaugesasspecifiedinSection5.
be drilled for mounting both 89-mm (3 ⁄2-in.) and 114-mm
(4 ⁄2-in.) dial size gauges and Type II gauge boards shall be
drilled for mounting both 152-mm (6-in.) and 216-mm (8 ⁄2-
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
in.) dial size gauges. When specified by the purchaser, drilling
Machinery and Piping Systems.
shall be limited to one size gauge for either Type I or Type II
Current edition approved April 1, 2011. Published April 2011. Originally
gauge boards (see 4.1.6).
approved in 1981. Last previous edition approved in 2006 as F707/F707M – 94
(2006). DOI: 10.1520/F0707_F0707M-94R11.
2 6. Dimensions and Permissible Variations
Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036, http://www.ansi.org.
6.1 The dimensions of the gauge board shall not vary by
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
more than 0.4 mm (6 ⁄64 in.) except as noted in Fig. 1 and Fig.
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
dodssp.daps
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F707/F707M − 94 (Reapproved 2011) F707/F707M − 94 (ReapprovedAn American National2011)Standard
Standard Specification for
Modular Gauge Boards
This standard is issued under the fixed designation F707/F707M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1 1
1.1 This specification covers modular gauge boards for mounting 89-mm (3 ⁄2-in.), 114-mm (4 ⁄2-in.), 152-mm (6-in.), and
216-mm (8 ⁄2-in.) dial size pressure gauges and dial thermometers for miscellaneous shipboard applications.
1.2 Gauge boards ordered under this specification are suitable for pressure gauges and dial thermometers with either turret or
back flanged type cases and with either back or bottom connections (see Appendix X1).
1.3 Gauge mounting dimensions shall be in accordance with ANSI B 40.01
1.4 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for
information only.
NOTE 1—Gauge boards covered by this specification are those normally supplied by the shipyard as opposed to the shipyard’s equipment subcontractor.
2. Referenced Documents
2.1 Other Standards:
B 40.1 Gauges, Pressure and Vacuum, Indicating Dial Type—Elastic Element
Fed Spec. TT-P-645 Primer, Paint, Zinc-Chromate, Alkyd Type
DoD-P-15328 Primer (Wash), Pretreatment (Formula No. 117 for Metals) (Metric)
3. Classification
3.1 Gauge boards are furnished in two types as follows:
1 1
3.1.1 Type I—Gauge boards for mounting 89-mm (3 ⁄2-in.) and 114-mm (4 ⁄2-in.) dial size gauges as specified in Section 5.
3.1.2 Type II—Gauge boards for mounting 152-mm (6-in.) and 216-mm (8 ⁄2-in.) dial size gauges as specified in Section 5.
3.2 Gauge boards are furnished in two grades as follows:
3.2.1 Grade a—Gauge boards are to be manufactured from carbon steel as specified in Section 5.
3.2.2 Grade b—Gauge boards are to be manufactured from aluminum alloy as specified in Section 5.
4. Ordering Information
4.1 Orders for gauge boards under this specification shall include the following information:
4.1.1 Quantity (number of gauge boards),
4.1.2 Name of item (gauge board),
4.1.3 Type (Type I or Type II as specified by purchaser), see 3.1.1 and 3.1.2,
4.1.4 Grade (Grade a or Grade b as specified by purchaser), see 3.2.1 and 3.2.2,
4.1.5 Paint (as specified by purchaser), see 7.2,
4.1.6 Drilling for gauge mounting (as specified by purchaser), see 5.1.1, and
4.1.7 ASTM designation and date of issue.
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery and Piping Systems.
Current edition approved April 1, 2011. Published April 2011. Originally approved in 1981. Last previous edition approved in 2006 as F707/F707M – 94 (2006). DOI:
10.1520/F0707_F0707M-94R11.
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F707/F707M − 94 (2011)
5. Materials and Manufacture
5.1 Unless otherwise specified the gauge boards shall be manufactured from 11-gauge (manufacturers standard gauge) carbon
steel for Grade a and 3 mm ( ⁄8 in.) thick aluminum alloy for Grade b. Materials shall be capable of being bent at room temperature
through 90° in any direction to an inside radius equal to its thickness without cracking on the outside of the bent portion.
1 1
5.1.1 Unless otherwise specified, Type I gauge boards shall be drilled for mounting both 89-mm (3 ⁄2-in.) and 114-mm (4 ⁄2-in.)
dial size gauges and Type II gauge boards shall be drilled for mounting b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.