ASTM C1265-17

Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications

SIGNIFICANCE AND USE
5.1 Frequently IG units are adhered with a structural sealant to a metal framing system. In such applications, only the inward lite of glass is usually adhered to the frame. As a result, a significant portion of any outward-acting or negative wind load must be carried in tension by the joint seal between the two lites of the IG unit. This test will not provide information on the integrity of the IG unit primary seal; however, it may provide data on load sharing between the primary IG vapor seal and the secondary structural sealant.  
5.2 Although this test method prescribes one environmental condition, other environmental conditions and exposure cycles can be employed for specific project evaluation. Such deviations should be described when reporting the data.
SCOPE
1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.”  
1.2 The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test method must recognize that the IG edge seal assembly influences the secondary sealant properties.  
1.3 The values determined by this test method will be characteristic of the particular edge seal assembly that is tested.  
Note 1: Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized as having the necessary durability for use in structural sealant glazing applications.  
1.4 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are approximate equivalents, provided for information purposes.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 14-Sep-2017
• ICS: 81.040.20 - Glass in building
• Technical Committee: C24 - Building Seals and Sealants
• Drafting Committee: C24.30 - Adhesion

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1265 − 17
Standard Test Method for
Determining the Tensile Properties of an Insulating Glass
1
Edge Seal for Structural Glazing Applications
This standard is issued under the fixed designation C1265; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This test method covers a laboratory procedure for
quantitatively measuring the tensile strength, stiffness, and
2. Referenced Documents
adhesion properties of insulating glass edge seals that are used
2
2.1 ASTM Standards:
in structural sealant glazing applications. Edge seals for these
C717 Terminology of Building Seals and Sealants
applicationsuseastructuralsealanttobondbothglasslitesand
the edge spacer into a monolithic sealed insulating glass unit.
3. Terminology
In typical applications, the structural sealant acts to hold the
3.1 Definitions—Refer to Terminology C717 for definitions
outside lite in place under wind and gravity load and to
of the following terms used in this test method: adhesive
maintain the edge spacer in its proper position. Hereafter, the
failure, cohesive failure, elastomeric, glazing, lite, primer, seal,
term “insulating glass” will be abbreviated as “IG.”
sealant, silicone sealant, structural sealant, substrate, stan-
1.2 The characterization of the IG secondary sealant
dard conditions.
properties, as defined by this test method, are strongly depen-
dent on glass and edge spacer cleaning procedures, IG spacer
4. Summary of Test Method
profile, location of spacer, and primary IG sealant application.
4.1 Five specimens are fabricated to duplicate the edge seal
Users of this test method must recognize that the IG edge seal
design of an IG unit for structural glazing applications. After
assembly influences the secondary sealant properties.
the secondary structural sealant is cured the specimens are
1.3 The values determined by this test method will be
tested to failure in tension. Testing is conducted at 23 6 2°C
characteristicoftheparticularedgesealassemblythatistested.
(74 6 3.6°F) at a rate of 5 6 0.5 mm (0.2 6 0.02 in.) per
minute. Strength, load-displacement response, failure mode,
NOTE 1—Presently, only elastomeric, chemically curing silicone seal-
ants specifically formulated for use as the secondary seal of IG units are
and primary IG edge seal behavior are recorded.
recognized as having the necessary durability for use in structural sealant
glazing applications.
5. Significance and Use
1.4 The values stated in SI (metric) units are to be regarded
5.1 Frequently IG units are adhered with a structural sealant
asthestandard.Theinch-poundvaluesgiveninparenthesesare
to a metal framing system. In such applications, only the
approximate equivalents, provided for information purposes.
inward lite of glass is usually adhered to the frame.As a result,
1.5 This standard does not purport to address all of the
a significant portion of any outward-acting or negative wind
safety concerns, if any, associated with its use. It is the
load must be carried in tension by the joint seal between the
responsibility of the user of this standard to establish appro-
two lites of the IG unit. This test will not provide information
priate safety, health, and environmental practices and deter-
on the integrity of the IG unit primary seal; however, it may
mine the applicability of regulatory limitations prior to use.
providedataonloadsharingbetweentheprimaryIGvaporseal
1.6 This international standard was developed in accor-
and the secondary structural sealant.
dance with internationally recognized principles on standard-
5.2 Although this test method prescribes one environmental
ization established in the Decision on Principles for the
condition, other environmental conditions and exposure cycles
Development of International Standards, Guides and Recom-
can be employed for specific project evaluation. Such devia-
tions should be described when reporting the data.
1
This test method is under the jurisdiction of ASTM Committee of C24 on
Building Seals and SealantsandisthedirectresponsibilityofSubcommittee C24.30
2
on Adhesion. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 15, 2017. Published October 2011. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1994. Last previous edition approved in 2011 as C1265-94(2011). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1265-17. the ASTM website.
Copy
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1265 − 94 (Reapproved 2011) C1265 − 17
Standard Test Method for
Determining the Tensile Properties of an Insulating Glass
1
Edge Seal for Structural Glazing Applications
This standard is issued under the fixed designation C1265; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion
properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications
use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical
applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer
in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.”
1.2 The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass
and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test
method must recognize that the IG edge seal assembly influences the secondary sealant properties.
1.3 The values determined by this test method will be characteristic of the particular edge seal assembly that is tested.
NOTE 1—Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized
as having the necessary durability for use in structural sealant glazing applications.
1.4 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are
approximate equivalents, provided for information purposes.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C717 Terminology of Building Seals and Sealants
3. Terminology
3.1 Definitions—Refer to Terminology C717 for definitions of the following terms used in this test method: adhesive failure,
cohesive failure, elastomeric, glazing, lite, primer, seal, sealant, silicone sealant, structural sealant, substrate.substrate, standard
conditions.
4. Summary of Test Method
4.1 Five specimens are fabricated to duplicate the edge seal design of an IG unit for structural glazing applications. After the
secondary structural sealant is cured the specimens are tested to failure in tension. Testing is conducted at 23 6 2°C (74 6 3.6°F)
at a rate of 5 6 0.5 mm (0.2 6 0.02 in.) per minute. Strength, load-displacement response, failure mode, and primary IG edge seal
behavior are recorded.
1
This test method is under the jurisdiction of ASTM Committee of C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.30 on
Adhesion.
Current edition approved Dec. 1, 2011Sept. 15, 2017. Published December 2011October 2011. Originally approved in 1994. Last previous edition approved in 20052011
ε1
as C1265-94(2005)C1265-94(2011). . DOI: 10.1520/C1265-94R11.10.1520/C1265-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1265 − 17
5. Significance and Use
5.1 Frequently IG units are adhered with a structural sealant to a metal framing system. In such applications, only the inward
lite of glass is usually adher
...