iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C270-07

(Specification)

Standard Specification for Mortar for Unit Masonry

Standard Specification for Mortar for Unit Masonry

SCOPE
1.1 This specification covers mortars for use in the construction of non-reinforced and reinforced unit masonry structures. Four types of mortar are covered in each of two alternative specifications: (1) proportion specifications and (2) property specifications.
Note 1—When the property specification is used to qualify masonry mortars, the testing laboratory performing the test methods should be accredited in accordance with Practice C 1093.
1.2 The proportion or property specifications shall govern as specified.
1.3 When neither proportion or property specifications are specified, the proportion specifications shall govern, unless data are presented to and accepted by the specifier to show that mortar meets the requirements of the property specifications.
1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 The terms used in this specification are identified in Terminologies C 1180 and C 1232.
1.6 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jan-2007
ICS
91.100.10 - Cement. Gypsum. Lime. Mortar
Technical Committee
C12 - Mortars and Grouts for Unit Masonry
Drafting Committee
C12.03 - Specifications for Mortars
Current Stage
Ref Project

Relations

Replaces
ASTM C270-06 - Standard Specification for Mortar for Unit Masonry
Effective Date
01-Feb-2007
Replaced By
ASTM C270-07a - Standard Specification for Mortar for Unit Masonry
Effective Date
15-Dec-2007
Referred By
ASTM D7147-21 - Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers
Effective Date
01-Feb-2007
Referred By
ASTM C1314-23a - Standard Test Method for Compressive Strength of Masonry Prisms
Effective Date
01-Feb-2007
Referred By
ASTM E1602-03(2017) - Standard Guide for Construction of Solid Fuel Burning Masonry Heaters
Effective Date
01-Feb-2007
Referred By
ASTM C1714/C1714M-23 - Standard Specification for Preblended Dry Mortar Mix for Unit Masonry
Effective Date
01-Feb-2007
Referred By
ASTM C1780-23a - Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer
Effective Date
01-Feb-2007
Referred By
ASTM C387/C387M-23 - Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
Effective Date
01-Feb-2007
Referred By
ASTM C1400-11(2017) - Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls
Effective Date
01-Feb-2007
Referred By
ASTM E2266-22 - Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
Effective Date
01-Feb-2007
Referred By
ASTM C141/C141M-14(2022) - Standard Specification for Hydrated Hydraulic Lime for Structural Purposes
Effective Date
01-Feb-2007
Referred By
ASTM C1180-22 - Standard Terminology of Mortar and Grout for Unit Masonry
Effective Date
01-Feb-2007
Referred By
ASTM C946-23 - Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls
Effective Date
01-Feb-2007
Referred By
ASTM E754-80(2022) - Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints
Effective Date
01-Feb-2007
Referred By
ASTM C1403-22a - Standard Test Method for Rate of Water Absorption of Masonry Mortars
Effective Date
01-Feb-2007

Buy Standard

ASTM C270-07 - Standard Specification for Mortar for Unit MasonryASTM C270-07 - Standard Specification for Mortar for Unit Masonry
PreviousNext
Technical specification
ASTM C270-07 - Standard Specification for Mortar for Unit Masonry
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 270 – 07
Standard Specification for
1
Mortar for Unit Masonry
This standard is issued under the fixed designation C 270; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C 109/C 109M Test Method for Compressive Strength of
Hydraulic Cement Mortars(Using 2-in. or [50-mm] Cube
1.1 Thisspecificationcoversmortarsforuseintheconstruc-
Specimens)
tion of non-reinforced and reinforced unit masonry structures.
C110 Test Methods for Physical Testing of Quicklime,
Four types of mortar are covered in each of two alternative
Hydrated Lime, and Limestone
specifications: (1) proportion specifications and (2) property
C 128 Test Method for Density, Relative Density (Specific
specifications.
Gravity), and Absorption of Fine Aggregate
NOTE 1—When the property specification is used to qualify masonry
C 144 Specification for Aggregate for Masonry Mortar
mortars, the testing laboratory performing the test methods should be
C 150 Specification for Portland Cement
accredited in accordance with Practice C 1093.
C 188 Test Method for Density of Hydraulic Cement
1.2 Theproportionorpropertyspecificationsshallgovernas
C 207 Specification for Hydrated Lime for Masonry Pur-
specified.
poses
1.3 When neither proportion or property specifications are
C 305 PracticeforMechanicalMixingofHydraulicCement
specified, the proportion specifications shall govern, unless
Pastes and Mortars of Plastic Consistency
data are presented to and accepted by the specifier to show that
C511 Specification for Mixing Rooms, Moist Cabinets,
mortar meets the requirements of the property specifications.
Moist Rooms, and Water Storage Tanks Used in the
1.4 The text of this specification references notes and
Testing of Hydraulic Cements and Concretes
footnotes which provide explanatory material. These notes and
C 595 Specification for Blended Hydraulic Cements
footnotes (excluding those in tables and figures) shall not be
C 780 Test Method for Preconstruction and Construction
considered as requirements of the standard.
Evaluation of Mortars for Plain and Reinforced Unit
1.5 The terms used in this specification are identified in
Masonry
Terminologies C 1180 and C 1232.
C 952 TestMethodforBondStrengthofMortartoMasonry
1.6 The following safety hazards caveat pertains only to the
Units
test methods section of this specification: This standard does
C 979 Specification for Pigments for Integrally Colored
not purport to address all of the safety concerns, if any,
Concrete
associated with its use. It is the responsibility of the user of this
C 1072 Test Method for Measurement of Masonry Flexural
standard to establish appropriate safety and health practices
Bond Strength
and determine the applicability of regulatory limitations prior
C 1093 Practice for Accreditation of Testing Agencies for
to use.
Masonry
C 1157 Performance Specification for Hydraulic Cement
2. Referenced Documents
C 1180 Terminology of Mortar and Grout for Unit Masonry
2
2.1 ASTM Standards:
C 1232 Terminology of Masonry
C5 Specification for Quicklime for Structural Purposes
C 1324 Test Method for Examination andAnalysis of Hard-
C91 Specification for Masonry Cement
ened Masonry Mortar
C 1329 Specification for Mortar Cement
C 1357 Test Methods for Evaluating Masonry Bond
1
This specification is under the jurisdiction of ASTM Committee C12 on
Strength
Mortars and Grouts for Unit Masonry and is the direct responsibility of Subcom-
mittee C12.03 on Specifications for Mortars.
C 1489 Specification for Lime Putty for Structural Purposes
Current edition approved Feb. 1, 2007. Published February 2007. Originally
C 1506 Test Method for Water Retention of Hydraulic
approved in 1951. Last previous edition approved in 2006 as C 270 – 06.
Cement-Based Mortars and Plasters
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C270–07
C 1586 Guide for Quality Assurance of Mortars be added to mortar unless specified. Coloring pigments shall
E72 Test Methods of Conducting Strength Tests of Panels conform to Specification C 979. Calcium chloride, when ex-
for Building Construction plicitly provided for in the contra
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1714/C1714M-23(Specification)
Standard Specification for Preblended Dry Mortar Mix for Unit Masonry

ABSTRACT
This specification covers unit masonry mortars whose material and design requirements are governed by a referenced ASTM document stated herein, but are preblended dry in a factory instead of produced from individual raw materials delivered to the job-site. Because field sampling, testing, directly comparable test results, packaging, and traceability of ingredients of preblended dry mortar mix differ from job site mixed mortars, this specification particularly addresses these issues, along with the tight control of ingredient ratios possible with preblended dry mortars.
SCOPE
1.1 This specification covers masonry mortars whose materials and design requirements are governed by Specification C270 but are preblended dry in a factory instead of produced from individual raw materials delivered to the job-site.  
1.2 The field-sampling, testing, directly comparable test results, packaging, and the traceability of ingredients of preblended dry mortar mix differ from job site mixed mortars and this standard specifically addresses these issues. The tight control of ingredient ratios possible with preblended dry mortar is also covered.  
1.3 The text of this specification refers to notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered the requirements of the standard.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C780-23(Test Method)
Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry

SIGNIFICANCE AND USE
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system.  
5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system best suited for the masonry to be constructed. The recommended tests and their significance are as follows:  
5.2.1 Consistency determinations by cone penetration (Annex A1) allow gaging the water additions for all mortars included in the preconstruction test series. Even if the mortar consistency as measured at the construction site is at a different penetration value than those measured during the preconstruction tests, the cone preparation test serves to standardize water additions for mortars being considered as alternatives before construction. Additional testing of mortar water content-consistency relationships (Annex A4) will allow relating these two factors to batch-to-batch variations at the construction site.  
5.2.2 Consistency retention by cone penetration (Annex A2) using disturbed or undisturbed mortar samples provides a means of establishing the early-age setting and stiffening characteristics of the mortars. Because laboratory testing is conducted under static climatic conditions, consistency retention test results reflect the relative performance of the mortar systems under test. The same general relationships are expected to hold during testing at the construction project, except as they are influenced by jobsite weather conditions.  
5.2.3 Mortar water-content determinations (Annex A4) allow measurement of the water content of the mortar mixture. Mortars prebatched using moist masonry sand may be mathematically analyzed for mortar water content; however, this test, when used for preconstruction evaluation, establishes the effectiveness of the test method and serves as the control or base for tests performed at the construction site.  
5.2.4 Mortar ...
SCOPE
1.1 These test methods cover procedures for the sampling and testing of mortars for composition and for their plastic and hardened properties, either before or during their actual use in construction.
Note 1: Guide C1586 provides guidance on evaluating mortar and clarifies the purpose of both these test methods and Specification C270.
Note 2: The testing agency performing these test methods should be evaluated in accordance with Practice C1093.  
1.2 Preconstruction Evaluation—These test methods permit comparisons of mortars made from different materials under simulated field conditions. They are also used to establish baseline values for comparative evaluation of field mortars.  
1.3 Construction Evaluation—Use of these methods in the field provide a means for quality assurance of field-mixed mortar. They include methods for verifying the mortar mix proportions, comparing test results for field mortars to preconstruction testing, and determining batch-to-batch uniformity of the mortar.  
1.4 The test results obtained under these test methods are not required to meet the minimum compressive values in accordance with the property specifications in Specification C270.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific ...

  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    17 pages
    English language
    sale 15% off
ASTM
ASTM C1713-23(Specification)
Standard Specification for Mortars for the Repair of Historic Masonry

SCOPE
1.1 This specification covers mortar for the repair of masonry constructed with methods and materials that pre-date the origination of current standards of construction. The mortar may be used for non-structural purposes such as repointing of the masonry, or for structural purposes such as, but not restricted to, re-construction or repair of mortar joints that contribute to the structural integrity of the masonry.  
1.2 Masonry includes the following units laid in mortar: (1) cast stone, (2) clay brick and tile, (3) concrete masonry, (4) natural stone, (5) terra cotta, and (6) calcium silicate.  
1.3 This specification may be used to pre-qualify mortar for a project.  
1.4 Mortars tested using this specification are laboratory-prepared mortars and do not represent in-place, site mortars.  
1.5 This specification provides a basis for the design of an appropriate mortar formulation based upon performance, material and aesthetic requirements. Use of this specification requires a thorough understanding of the function, maintenance, and repair requirements for the preservation and continued performance of the masonry assembly in the context of the assembly’s structure, water management, and long-term performance.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM C476-23(Specification)
Standard Specification for Grout for Masonry

ABSTRACT
This specification covers two types of grout, fine and coarse grout, for use in the construction of masonry structures. Grout is specified by proportions or strength requirements. Materials used as ingredients in grout shall conform to the requirements specified such as: cementitious materials; blended cements; quicklime; hydrated lime; coal fly ash or raw calcine natural pozzolan; granulated blast furnace slag; air-entraining admixtures; aggregates; water; pumping aids; antifreeze compounds; and storage of materials. Fine grout shall be manufactured with fine aggregates. Coarse grout shall be manufactured with a combination of coarse and fine aggregates. Proportions of ingredients shall be determined by grout proportion requirements and by the specified compressive strength. Materials for grout shall be measured in such a way that the required proportions of the grout materials are controlled and accurately measured. Grout shall be produced using one of the following procedures: grout materials mixed with water at the job site and ready-mixed grout transported to the job site.
SCOPE
1.1 This specification covers two types of grout, fine and coarse grout, for use in the construction of masonry structures. Each type (fine and coarse) is further classified as conventional grout (requiring mechanical consolidation by puddling or vibration when placed) and self-consolidating grout (not requiring mechanical consolidation when placed). Conventional grout is specified by (1) proportions or (2) strength requirements. Self-consolidating grout is specified by strength requirements.  
1.2 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1403-22a(Test Method)
Standard Test Method for Rate of Water Absorption of Masonry Mortars

SIGNIFICANCE AND USE
4.1 This test method provides a laboratory procedure for determining the relative water absorption properties over time of mortars used for masonry construction. Because the specimens are made under laboratory conditions and do not take into account the effect of the masonry substrate or field mixing procedures, this method is not intended for field use. Data generated from this test method may be useful for determining the relative effectiveness of water repellent admixtures or the effect of other admixtures or mortar components on the water repellency of a mortar. However, use caution in interpreting the results. While the resistance of masonry to water penetration may be related to the water absorption of the mortar, it also depends on other factors, such as the workmanship, extent of bond, and the properties of the masonry units and mortar.
Note 1: This test method is specified in Specification C1384 for demonstrating compliance of mortar admixtures classified as Water Repellent. In this compliance testing, the admixed mortar is compared to a reference mortar made with the same mortar materials except that it does not include the admixture. For quality control testing of water repellent preblended dry mortar mixes, the reference mortar is not typically available since the water repellent additive is added during the manufacturing process prior to bagging the final product. In these cases, the procedure in Annex A1 can be used to determine the relative resistance of the mortar to absorption by capillary uptake.
SCOPE
1.1 This test method covers a standardized laboratory procedure for determining the relative water absorption by capillary uptake (wicking) characteristics of masonry mortars. This test method is not applicable for determining the effectiveness of water repellent coatings.  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Inch-pound units are given in parentheses for temperature specification and are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1180-22(Terminology)
Standard Terminology of Mortar and Grout for Unit Masonry

SCOPE
1.1 This terminology covers terms, definitions of terms, descriptions of terms, nomenclature, and explanations of abbreviations, acronyms, and symbols specifically associated with standards under the jurisdiction of ASTM Committee C12 on Mortars and Grouts for Unit Masonry.  
1.2 The definitions and descriptions of terms in this terminology pertain to Test Methods C780, C1019, C1148, C1324, and C1403; Specifications C144, C270, C404, C476, C887, and C1384; Practice C946; and Guide C1586.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1019-20(Test Method)
Standard Test Method for Sampling and Testing Grout for Masonry

SIGNIFICANCE AND USE
3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement.  
3.1.1 During construction, grout is placed within or between absorptive masonry units. Excess water must be removed from grout specimens in order to provide compressive strength test results more nearly indicative of the grout strength in the wall. In this test method, molds are made from masonry units having the same absorption and moisture content characteristics as those being used in the construction.  
3.2 This test method is used to either help select grout proportions by comparing test values or as a quality control test for uniformity of grout preparation during construction.  
3.3 The physical exposure condition and curing of the grout are not exactly reproduced, but this test method does subject the grout specimens to absorption conditions similar to those experienced by grout in the wall.
Note 2: Test results of grout specimens taken from a wall should not be compared to test results obtained with this test method.
SCOPE
1.1 This test method covers procedures for both field and laboratory sampling and compression testing of grout used in masonry construction. Grout for masonry is specified under Specification C476.
Note 1: The testing agency performing this test method should be evaluated in accordance with Practice C1093.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM C1324-20a(Test Method)
Standard Test Method for Examination and Analysis of Hardened Masonry Mortar

SIGNIFICANCE AND USE
4.1 This test method provides procedures for petrographic examination and chemical analysis of mortar for components of masonry mortar. These components may include portland cement, hydrated calcitic or dolomitic lime, masonry cement, aggregates, and air.  
4.2 The test method consists of procedures and sub-procedures, each requiring a substantial degree of petrographic and chemical skills and relatively elaborate instrumentation.  
4.3 The chemical data considered together with results of petrographic examination of a mortar provide for calculation of component proportions and thus allow a determination of mortar composition as represented by Types M, N, S, and O in Table 1 (Proportion Specification Requirements) of Specification C270.  
4.4 Failure of a mortar to have the composition of any type as defined in Table 1 of Specification C270 does not necessarily mean that the mortar does not meet the requirements of Specification C270. The mortar may meet the alternative requirements of Table 2 (Property Specification Requirements) of Specification C270.  
4.5 The maleic acid method of analysis is not applicable for the analysis of mortar because it is greatly influenced by carbonation and does not provide for the determination of calcium.
SCOPE
1.1 This test method covers procedures for petrographic examination and chemical analysis of samples of masonry mortars. Based upon such examination and analysis, proportions of components in masonry mortars can be determined.
Note 1: This method is also applicable to hydraulic cement-based stucco and plaster. Some historic mortars may contain non-resolvable constituents that may interfere. However, significant information may be obtained by petrographic examinations.  
1.2 Interpretations and calculations of chemical results are dependent upon results of the petrographic examination. The use of the chemical results alone is contrary to the requirements of this test method.  
1.3 Procedures for sampling, petrographic examination, chemical analysis, and calculations of component proportions are given in the following sections:    
Section  
Sampling  
7  
Petrographic examination  
8  
Chemical analysis  
9  
Mortar proportion calculations  
10  
Report  
11  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1586-20(Guide)
Standard Guide for Quality Assurance of Mortars

SIGNIFICANCE AND USE
3.1 This document is intended to provide guidance and clarification to designers, specifiers, inspectors, testing agencies, producers, and users in specifying and evaluating masonry mortar.  
3.2 Users of documents Specification C270 and Test Method C780 often confuse and sometimes inadvertently misuse parts of the two documents when specifying or evaluating masonry mortar. This guide seeks to address specific items within Specification C270 and Test Method C780 to help promote their proper use and interpretation.
SCOPE
1.1 This document provides guidance regarding the proper use of Specification C270 and Test Method C780 for evaluating masonry mortar produced in the laboratory and at the construction site.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM C887-20(Specification)
Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

ABSTRACT
This specification covers the materials, properties, and packaging of dry, combined materials for use as surface bonding mortar with concrete masonry units that have not been prefaced, coated, or painted. The materials used as ingredients shall consist of the following: cements which shall be a Portland cement, blended hydraulic cement, hydraulic cement, or masonry cement; Type S or SA hydrated lime; Class N, F, or S pozzolan; aggregates; glass fibers; and additives. Physical properties of the packaged materials shall conform to the flexural strength, compressive strength, time of setting, and water retention requirements. The net weight, amount of mixing water, unit weight, and yield of the surface bonding mortar shall be calculated and reported.
SCOPE
1.1 This specification covers the materials, properties, and packaging of dry, combined materials for use as surface bonding mortar with concrete masonry units that have not been prefaced, coated, or painted.  
1.2 This specification does not cover design or application. Consult the manufacturer for specific recommendations.  
1.3 Appendix X1 of this specification contains the recommended tests for evaluation of surface bonded masonry assemblages used to establish design loads for the composite wall.  
1.4 Appendix X2 through Appendix X5 of this specification contain additional tests that may be performed on surface bonding mortar.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. This hazard statement applies only to Section 9 of this specification.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off