ASTM F1074-87(2018)

Standard Specification for Cleats, Welded Horn Type

ABSTRACT
This specification covers hollow welded horn type cleats and pads for marine use. The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts. The horn cleats shall be of galvanized steel, grade 1023W; the base plate shall be of the prescribed steel composition; and all chafing surfaces shall have the specified finish. The cleats’ horns shall be of cast steel, round in shape, and free of burrs or sharp edges. The requirements for welding of horns to a base plate are illustrated. The dimensional requirements for cleat, rope circumference, and roper diameter are specified. Requirements for packaging and product marking are given as well.
SCOPE
1.1 This specification covers hollow cleats and pads for marine use.  
1.2 The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2018
• ICS: 47.020.50 - Deck equipment and installations
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1074 − 87 (Reapproved 2018) An American National Standard
Standard Specification for
1
Cleats, Welded Horn Type
This standard is issued under the fixed designation F1074; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Ordering Information
1.1 This specification covers hollow cleats and pads for 3.1 Orders for material under this specification shall include
the following:
marine use.
3.1.1 Title, number, and date of this specification,
1.2 The cleats shall be used where securing of boat handling
3.1.2 Quantity,
lines are required onboard commercial and navy boats and
3.1.3 Size of cleats, and
crafts.
3.1.4 Packaging, packing, or marking requirements.
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
4. Materials and Manufacture
conversions to SI units that are provided for information only
4.1 Material:
and are not considered standard.
4.1.1 The horn cleats shall be of galvanized steel, grade
1.4 This international standard was developed in accor-
1023W, in accordance with Practice A385.
dance with internationally recognized principles on standard-
4.1.2 The base plate shall be of steel, (carbon 0.35
ization established in the Decision on Principles for the
maximum), in accordance with Specification A36/A36M.
Development of International Standards, Guides and Recom-
4.1.3 All chafing surfaces shall have a 125µ finish.
mendations issued by the World Trade Organization Technical
4.2 Manufacture—The cleats’ horns shall be of cast steel,
Barriers to Trade (TBT) Committee.
round in shape, and free of burrs or sharp edges. The horns
shall be welded to a base plate as shown in Fig. 1 (see Table 1).
2. Referenced Documents
The weld is to be ground smooth to prevent chafing of ropes.
2
2.1 ASTM Standards:
The base plate shall be oval shaped with smooth rounded
A36/A36M Specification for Carbon Structural Steel
edges. The dimensions shall be in accordance with Table 1.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
5. Packaging
A385 Practice for Providing High-Quality Zinc Coatings
5.1 The packing shall afford protection against deterioration
(Hot-Dip)
and physical damage during shipment from the manufacturer to
the using activity for immediate use.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
6. Product Marking
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
6.1 Containers shall be stenciled with the ASTM standard
Current edition approved April 1, 2018. Published May 2018. Originally
designation, in black paint with approximately 1 in. (25.4 mm)
approved in 1987. Last previous edition approved in 2012 as F1074 – 87 (2012).
high letters and numbers with the following information:
DOI: 10.1520/F1074-87R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
6.1.1 Address,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
6.1.2 purchase order number, and
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 6.1.3 Man
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1074 − 87 (Reapproved 2012) F1074 − 87 (Reapproved 2018)An American National Standard
Standard Specification for
1
Cleats, Welded Horn Type
This standard is issued under the fixed designation F1074; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers hollow cleats and pads for marine use.
1.2 The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A385 Practice for Providing High-Quality Zinc Coatings (Hot-Dip)
3. Ordering Information
3.1 Orders for material under this specification shall include the following:
3.1.1 Title, number, and date of this specification,
3.1.2 Quantity,
3.1.3 Size of cleats, and
3.1.4 Packaging, packing, or marking requirements.
4. Materials and Manufacture
4.1 Material:
4.1.1 The horn cleats shall be of galvanized steel, grade 1023W, in accordance with Practice A385.
4.1.2 The base plate shall be of steel, (carbon 0.35 maximum), in accordance with Specification A36/A36M.
4.1.3 All chafing surfaces shall have a 125μ finish.
4.2 Manufacture—The cleats’ horns shall be of cast steel, round in shape, and free of burrs or sharp edges. The horns shall be
welded to a base plate as shown in Fig. 1 (see Table 1). The weld is to be ground smooth to prevent chafing of ropes. The base
plate shall be oval shaped with smooth rounded edges. The dimensions shall be in accordance with Table 1.
5. Packaging
5.1 The packing shall afford protection against deterioration and physical damage during shipment from the manufacturer to the
using activity for immediate use.
6. Product Marking
6.1 Containers shall be stenciled with the ASTM standard designation, in black paint with approximately 1 in. (25.4 mm) high
letters and numbers with the following information:
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved June 1, 2012April 1, 2018. Published October 2012May 2018. Originally approved in 1987. Last previous edition approved in 20072012 as
F1074 – 87 (2007).(2012). DOI: 10.1520/F1074-87R12.10.1520/F1074-87R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, o
...