ASTM C1315-00

Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete

SCOPE
1.1 This specification provides requirements for membrane-forming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light.  
1.2 The values stated in SI units are to be regarded as the standard. (Inch pound units are shown in parentheses).  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Jun-2000
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.22 - Materials Applied to New Concrete Surfaces

Relations

• Replaced By: ASTM C1315-03 - Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
• Effective Date: 10-Jan-2003
• Referred By: ASTM C309-19 - Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete
• Effective Date: 10-Jun-2000
• Referred By: ASTM F2551-09(2023) - Standard Practice for Installing a Protective Cementitious Liner System in Sanitary Sewer Manholes
• Effective Date: 10-Jun-2000

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 1315 – 00
Standard Specification for
Liquid Membrane-Forming Compounds Having Special
1
Properties for Curing and Sealing Concrete
This standard is issued under the fixed designation C 1315; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 3723 Test Method for Pigment Content of Water-
5
Emulsion Paints by Low-Temperature Ashing
1.1 This specification provides requirements for membrane-
D 4541 Method for Pull-Off Strength of Coatings Using
forming liquids suitable for use as curing compounds and
4
Portable Adhesion Testers
sealers on freshly placed concrete and as sealers on hardened
E 1347 Test Method for Color and Color-Difference Mea-
concrete. These membranes have special properties, such as,
5
surement by Tristimulus (Filter) Colorimetry
alkali resistance, acid resistance, adhesion-promoting qualities,
G 53 Practice for Operating Light- and Water-Exposure
and resistance to degradation by UV light.
Apparatus (Fluorescent UV-Condensation Type) for Expo-
1.2 The values stated in SI units are to be regarded as the
6
sure of Nonmetallic Materials
standard. (Inch pound units are shown in parentheses).
2.2 Other Standards:
1.3 The following precautionary caveat pertains only to the
ANSI A136.1–1992 Type I Organic Adhesives for Installa-
test methods portion, Section 8, of this specification. This
7
tion of Ceramic Tile
standard does not purport to address all of the safety concerns,
8
RFCI Specification ADH-1 Type III, Class 3
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health
3. Classification
practices and determine the applicability of regulatory limita-
3.1 The following types of liquid membrane-forming com-
tions prior to use.
pounds are included:
2. Referenced Documents 3.1.1 Type I—Clear or translucent, and
3.1.2 Type II—White pigmented.
2.1 ASTM Standards:
3.2 The curing compound shall conform to one of the
C 156 Test Method for Water Retention by Concrete Curing
2
following classes:
Materials
3
3.2.1 Class A curing compounds conform to the require-
D 56 Test Method for Flash Point by Tag Closed Tester
ments of 6.4.1, and are essentially non-yellowing,
D 869 Test Method for Evaluating Degree of Settling of
4
3.2.2 Class B curing compounds conform to the require-
Paint
ments of 6.4.2, where moderate yellowing is not prohibited,
D 1308 Test Method for Effect of Household Chemicals on
4
and
Clear and Pigmented Organic Finishes
3.2.3 Class C curing compounds are not restricted with
D 1309 Test Method for Settling Properties of Traffic Paints
4
regard to yellowing or darkening, and are for use where the
During Accelerated Storage
color changes are acceptable.
D 1544 Test Method for Color of Transparent Liquids
5
(Gardner Color Scale)
NOTE 1—Polymer materials known to satisfy the durability require-
D 1734 Practice for Making Cementitious Panels for Test- ments of this document include, but are not limited to, chlorinated rubbers,
4
styrene-acrylate and styrene-butadiene copolymers. These polymers have
ing Coatings
5
demonstrated their durability by their ability to adhere to concrete and not
D 2369 Test Method for Volatile Content of Coatings
be affected by the alkalies from cement.
D 2371 Test Method for Pigment Content of Solvent Re-
NOTE 2—Pigmented colors other than white, or other special attributes,
5
ducible Paints
are beyond the scope of this specification and are subject to negotiation
between the purchaser and the supplier.
1
4. Ordering Information
This specification is under the jurisdiction of ASTM Committee C09 on
Concrete and Concrete Aggregatesand is the direct responsibility of Subcommittee
4.1 The purchaser shall include the following information in
C09.22on Curing Materials.
Current edition approved June 10, 2000. Published August 2000. Originally
6
published as C 1315–95. Last previous edition C 1315–95.
Annual Book of ASTM Standards, Vol 14.02.
2 7
Annual Book of ASTM Standards, Vol 04.02. American National Standard Specifications for the Installation of Ceramic Tile,
3
Annual Book of ASTM Standards, Vol 05.01. 1992, Tile Council of America, P.O. Box 1787, Clemson, SC 29633-1787.
4 8
Annual Book of ASTM Standards, Vol 06.02. Resilient Floor Covering Institute RFCI Specification ADH-1, Resilient Floor
5
Annual Book of ASTM Standards, Vol 06.01. Covering Institute, 966 Hungerford Dr., Suite 12B, Rockville, MD 20850.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This sta
...