ASTM C163-05

Standard Practice for Mixing Thermal Insulating Cement Samples

SIGNIFICANCE AND USE
Insulating cement must be mixed with water and molded to prepare for testing.
SCOPE
1.1 This practice covers mixing thermal insulating cement samples with water in the preparation of specimens for use in all tests on the cement.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Mar-2005
• ICS: 91.100.60 - Thermal and sound insulating materials
• Technical Committee: C16 - Thermal Insulation
• Drafting Committee: C16.31 - Chemical and Physical Properties

Relations

• Replaces: ASTM C163-88(1997) - Standard Practice for Mixing Thermal Insulating Cement Samples
• Effective Date: 01-Apr-2005
• Replaced By: ASTM C163-05(2010) - Standard Practice for Mixing Thermal Insulating Cement Samples
• Effective Date: 01-Sep-2010
• Referred By: ASTM C449-07(2019) - Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
• Effective Date: 01-Apr-2005
• Referred By: ASTM C166-05(2023) - Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
• Effective Date: 01-Apr-2005
• Referred By: ASTM C195-07(2019) - Standard Specification for Mineral Fiber Thermal Insulating Cement
• Effective Date: 01-Apr-2005
• Referred By: ASTM C196-00(2019) - Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
• Effective Date: 01-Apr-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C163–05
Standard Practice for
1
Mixing Thermal Insulating Cement Samples
This standard is issued under the fixed designation C163; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 5.3 Scales, accurate to within 0.5 oz (14.1 g) with a
minimum capacity of 15 lb (about 6.8 kg).
1.1 This practice covers mixing thermal insulating cement
5.4 Water Container, suitable for holding approximately 2
samples with water in the preparation of specimens for use in
gal (about 8 L) of water.
all tests on the cement.
5.5 Mold, constructed of either wood or metal.
1.2 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are provided
6. Mixing Water
for information only.
6.1 The mixing water shall be equal in quality to that used
1.3 This standard does not purport to address all of the
for domestic purposes. Its temperature shall be between 70 and
safety concerns, if any, associated with its use. It is the
75°F (21 and 24°C). The quantity used shall be that which
responsibility of the user of this standard to establish appro-
gives the consistency as recommended by the manufacturer.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
7. Procedure
7.1 Test at least one specimen from each lot of cement
2. Referenced Documents
2
unless otherwise agreed upon between user and supplier or as
2.1 ASTM Standards:
shown otherwise in a material specification.
C168 Terminology Relating to Thermal Insulation
7.2 Weighthespecimen(atleast3lb(1.4kg))ofdrycement
3. Terminology and place it on a smooth, nonabsorbent, and corrosion-resistant
surface.
3.1 Definitions: Terminology C168 shall be considered as
7.3 Form a crater in the center of the dry cement. Pour the
applying to the terms used in this practice.
mixing water slowly into the crater and determine the weight
4. Significance and Use
used.
7.4 Fold the material on the outer edge into the crater by
4.1 Insulatingcementmustbemixedwithwaterandmolded
means of the rectangular trowel.
to prepare for testing.
7.5 After the water has been in contact with the cement for
5. Apparatus
the period of time recommended by the manufacturer, mix
rapidly with the rectangular trowel until the entire batch is of
5.1 Mixing Surface or Pan, nonabsorbent and corrosion-
uniform consistency.
resistant surface or shallow pan approximately 3 ft (0.9 m)
7.6 Mold the cement specimen immediately after mixing or
square.
the time frame recommended by the manufacturer.
5.2 Trowels, 16-in. (about 400-mm) rectangular plasterer’s
trowel, and a 9-in. (about 230-mm) pointed trowel.
8. Preparation of Dried Specimens for Later Tests
8.1 Cover a piece of flat, heavy-gage metal with wax paper.
1
This practi
...