ASTM A1067/A1067M-12
(Specification)Standard Specification for Test Coupons for Steel Castings
Standard Specification for Test Coupons for Steel Castings
ABSTRACT
This specification defines the geometries of several separately-cast and integrally-cast test coupons for use as specified in the applicable casting product or common requirements standard. Procedures for molding, casting, heat treating, machining, or testing are not covered in the standard, and are instead addressed as needed and appropriate by the applicable product or common requirements standard. The applicable casting product standard or common requirements standard or both provide information regarding the number of coupons, molding materials to be used, heat treatment concerns, and other processing issues. The primary function of the test coupon is to provide sound specimens usable for the determination of mechanical, physical, corrosion, or other properties of the metal used to produce the castings. If the test results conform to the stated requirements, then the test coupon may be considered to have functioned acceptably.
SCOPE
1.1 This specification defines the geometries of several separately-cast and integrally-cast test coupons for use as specified in the applicable casting product or common requirements standard. This standard does not address procedures for molding, casting, heat treating, machining, or testing; these items are addressed as needed and appropriate by the applicable product or common requirements standard.Note 1—The test coupons described herein were formerly defined in multiple casting specifications. Those standards now reference this document when test coupons are required and should be consulted for applicable manufacturing and processing requirements.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A1067/A1067M −12
StandardSpecification for
1
Test Coupons for Steel Castings
This standard is issued under the fixed designation A1067/A1067M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3.2 Except where specified herein or in the applicable
product or common requirements standard, the details of the
1.1 This specification defines the geometries of several
gating and risering of the coupons are left to the discretion of
separately-cast and integrally-cast test coupons for use as
the producer.
specified in the applicable casting product or common require-
3.3 The test coupons shall be processed and heat-treated as
ments standard. This standard does not address procedures for
specified in the applicable product or common requirements
molding, casting, heat treating, machining, or testing; these
specification. Except when specified otherwise, the portion of
items are addressed as needed and appropriate by the appli-
the test coupon from which the test specimen or specimens are
cable product or common requirements standard.
to be machined may be cut from the riser or feeder prior to heat
NOTE 1—The test coupons described herein were formerly defined in
treatment.
multiple casting specifications. Those standards now reference this docu-
ment when test coupons are required and should be consulted for
4. Performance Requirements
applicable manufacturing and processing requirements.
4.1 The primary function of the test coupon is to provide
1.2 Units—The values stated in either SI units or inch-
sound specimens useable for the determination of mechanical,
pound units are to be regarded separately as standard. The
physical, corrosion, or other properties of the metal used to
values stated in each system may not be exact equivalents;
produce the castings. If the test results conform to the stated
therefore, each system shall be used independently of the other.
requirements, then the test coupon may be considered to have
Combining values from the two systems may result in non-
functioned acceptably.
conformance with the standard.
1.3 This standard does not purport to address all of the
5. Other Requirements
safety concerns, if any, associated with its use. It is the
5.1 The casting producer shall establish procedures for the
responsibility of the user of this standard to establish appro-
identification and traceability of the coupons from pouring
priate safety and health practices and determine the applica-
through testing.
bility of regulatory limitations prior to use.
6. Dimensions and Permissible Variations
2. Ordering Information
6.1 The drawings shown in this standard are not necessarily
2.1 The applicable casting product standard or common
drawn to scale. The values shown in the tables constitute the
requirements standard or both provide information regarding
dimensional requirements.
the number of coupons, molding materials to be used, heat
treatment concerns, and other processing issues.
6.2 The drawings shown in this standard depict the more
commonly used test coupons (Figs. 1-9). Other designs may be
3. Materials and Manufacture suitable when shown to produce acceptable properties or where
agreed.
3.1 Unless specified otherwise by the purchaser, test cou-
pons shall be poured from the same heat, or from the same
7. Workmanship, Finish, and Appearance
master heat, or from a sub-heat from the same master heat as
the castings they are to represent. 7.1 Care should be taken in the preparation and pouring of
the molds to avoid the creation of inclusions or other anomalies
in the resulting test specimens.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
8. Sampling
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.18 on Castings.
8.1 Care shall be taken in the production and processing of
Current edition approved May 1, 2012. Published August 2012. Originally
the test coupon to assure that it is representative of the casting
approved in 2010. Last previous edition approved in 2010 as A1067/A1067M–10.
DOI: 10.1520/A1067_A1067M-12. or castings it represents.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A1067/A1067M − 12
Feature 4–leg design 2–leg design
in. mm in. mm
1 1
A2 ⁄4 60 2 ⁄4 60
1 1
B1 ⁄4 35 1 ⁄4 35
C2 50 2 50
1 1
D1 ⁄4 35 1 ⁄4 35
E Optional Optional Optional Optional
3 7
W8 ⁄8 215 3 ⁄8 100
T* * * *
L 5 min. 125 min. 5 min. 1
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A1067 − 10 A1067/A1067M − 12
Standard Specification for
1
Test Coupons for Steel Castings
This standard is issued under the fixed designation A1067;A1067/A1067M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This standardspecification defines the geometries of several separately-cast and integrally-cast test coupons for use as
specified in the applicable casting product or common requirements standard. This standard does not address procedures for
molding, casting, heat treating, machining, or testing; these items are addressed as needed and appropriate by the applicable
product or common requirements standard.
NOTE 1—The test coupons described herein were formerly defined in multiple casting specifications. Those standards now reference this document
when test coupons are required and should be consulted for applicable manufacturing and processing requirements.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Ordering Information
2.1 The applicable casting product standard or common requirements standard or both provide information regarding the
number of coupons, molding materials to be used, heat treatment concerns, and other processing issues.
3. Materials and Manufacture
3.1 Unless specified otherwise by the purchaser, test coupons shall be poured from the same heat, or from the same master heat,
or from a sub-heat from the same master heat as the castings they are to represent.
3.2 Except where specified herein or in the applicable product or common requirements standard, the details of the gating and
risering of the coupons are left to the discretion of the producer.
3.3 The test coupons shall be processed and heat-treated as specified in the applicable product or common requirements
specification. Except when specified otherwise, the portion of the test coupon from which the test specimen or specimens are to
be machined may be cut from the riser or feeder prior to heat treatment.
4. Performance Requirements
4.1 The primary function of the test coupon is to provide sound specimens useable for the determination of mechanical,
physical, corrosion, or other properties of the metal used to produce the castings. If the test results conform to the stated
requirements, then the test coupon may be considered to have functioned acceptably.
5. Other Requirements
5.1 The casting producer shall establish procedures for the identification and traceability of the coupons from pouring through
testing.
6. Dimensions and Permissible Variations
6.1 The drawings shown in this standard are not necessarily drawn to scale. The values shown in the tables constitute the
dimensional requirements.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.18
on Castings.
Current edition approved May 1, 2010May 1, 2012. Published June 2010August 2012. Originally approved in 2010. Last previous edition approved in 2010 as
A1067/A1067M–10. DOI: 10.1520/A1067_A1067M-12.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A1067/A1067M − 12
6.2 The drawings shown in this standard depict the more commonly used test coupons (Figs. 1-89). Other designs may be
suitable when shown to produce acceptable properties or where agreed.
7. Workmanship, Finish, and Appearance
7.1 Care should be taken in the preparation and pouring of the molds to avoid the creation of inclusions or other anomalies in
the resulting test specimens.
8. Sampling
8.1 Care shall be taken in the production and processing of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.