ASTM A217/A217M-22
(Specification)Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
ABSTRACT
This specification covers steel castings, martensitic stainless steel and alloys steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for high-temperature and corrosive service. The grades of steels covered here are: Grade WC1, Grade WC4, Grade WC5, Grade WC6, Grade WC9, Grade WC11, Grade C5, Grade C12, Grade C12A, and Grade CA15. Heat treatment shall consist of normalizing and tempering for Grade C12A and tempering for all other grades. Heat treatments shall be performed after castings have been allowed to cool. Heat and product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, molybdenum, chromium, nickel, vanadium, manganese, phosphorus, sulfur, silicon, columbium, nitrogen, aluminum, copper, titanium, tungsten, and zirconium. The surface of the casting shall be examined visually and shall be free of adhering sand, scale, cracks and hot tears. Steels shall undergo tension test, and shall conform to the following mechanical requirements: tensile strength, yield strength, elongation, and reduction of area.
SCOPE
1.1 This specification2 covers martensitic stainless steel and alloy steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1) intended primarily for high-temperature and corrosive service (Note 2).
1.2 One grade of martensitic stainless steel and nine grades of ferritic alloy steel are covered. Selection will depend on design and service conditions, mechanical properties, and the high-temperature and corrosion-resistant characteristics (Note 3).
Note 1: Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M. Low alloy quench-and-tempered grades equivalent to Specification A217/A217M grades may be found in both Specifications A352/A352M and A487/A487M.
Note 2: The grades covered by this specification represent materials that are generally suitable for assembly with other castings or wrought steel parts by fusion welding. It is not intended to imply that these grades possess equal degrees of weldability; therefore, it is the responsibility of the purchaser to establish for himself a suitable welding technique. Since these grades possess varying degrees of suitability for high-temperature and corrosion-resistant service, it is also the responsibility of the purchaser to determine which grade shall be furnished, due consideration being given to the requirements of the applicable construction codes.
Note 3: The committee formulating this specification has included nine grades of materials that are considered to represent basic types of ferritic alloy steels suitable for valves, flanges, fittings, and other pressure-containing parts. Additional alloy steels that may better fulfill certain types of service will be considered for inclusion in this specification by the committee as the need becomes apparent.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:A217/A217M −22 Endorsed by Manufacturers Standardization Society
of the Valve and Fittings Industry
Endorsed by American Foundrymen’s Society
Used in USDOE-NE Standards
Standard Specification for
Steel Castings, Martensitic Stainless and Alloy, for
Pressure-Containing Parts, Suitable for High-Temperature
1
Service
This standard is issued under the fixed designationA217/A217M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* system shall be used independently of the other. Combining
2 values from the two systems may result in nonconformance
1.1 This specification covers martensitic stainless steel and
with the standard.
alloy steel castings for valves, flanges, fittings, and other
1.4 This international standard was developed in accor-
pressure-containing parts (Note 1) intended primarily for
dance with internationally recognized principles on standard-
high-temperature and corrosive service (Note 2).
ization established in the Decision on Principles for the
1.2 One grade of martensitic stainless steel and nine grades
Development of International Standards, Guides and Recom-
of ferritic alloy steel are covered. Selection will depend on
mendations issued by the World Trade Organization Technical
design and service conditions, mechanical properties, and the
Barriers to Trade (TBT) Committee.
high-temperature and corrosion-resistant characteristics (Note
3).
2. Referenced Documents
NOTE 1—Carbon steel castings for pressure-containing parts are cov-
3
2.1 ASTM Standards:
ered by Specification A216/A216M. Low alloy quench-and-tempered
A216/A216M SpecificationforSteelCastings,Carbon,Suit-
grades equivalent to Specification A217/A217M grades may be found in
both Specifications A352/A352M and A487/A487M. able for Fusion Welding, for High-Temperature Service
NOTE 2—The grades covered by this specification represent materials
A352/A352M Specification for Steel Castings, Ferritic and
that are generally suitable for assembly with other castings or wrought
Martensitic, for Pressure-Containing Parts, Suitable for
steel parts by fusion welding. It is not intended to imply that these grades
Low-Temperature Service
possess equal degrees of weldability; therefore, it is the responsibility of
A487/A487M Specification for Steel Castings Suitable for
the purchaser to establish for himself a suitable welding technique. Since
these grades possess varying degrees of suitability for high-temperature
Pressure Service
andcorrosion-resistantservice,itisalsotheresponsibilityofthepurchaser
A488/A488M Practice for Steel Castings, Welding, Qualifi-
to determine which grade shall be furnished, due consideration being
cations of Procedures and Personnel
given to the requirements of the applicable construction codes.
A703/A703M Specification for Steel Castings, General
NOTE 3—The committee formulating this specification has included
nine grades of materials that are considered to represent basic types of Requirements, for Pressure-Containing Parts
ferriticalloysteelssuitableforvalves,flanges,fittings,andotherpressure-
A802/A802M Practice for Steel Castings, Surface Accep-
containingparts.Additionalalloysteelsthatmaybetterfulfillcertaintypes
tance Standards, Visual Examination
of service will be considered for inclusion in this specification by the
A985/A985M Specification for Steel Investment Castings
committee as the need becomes apparent.
General Requirements, for Pressure-Containing Parts
1.3 The values stated in either SI units or inch-pound units
4
2.2 AWS Specifications:
are to be regarded separately as standard. The values stated in
A5.5/A5.5M Low-Alloy Steel Electrodes for Shielded Metal
each system may not be exact equivalents; therefore, each
Arc Welding
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3
A01.18 on Castings. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved March 1, 2022. Published March 2022. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1939. Last previous edition approved in 2020 as A217/A217M – 20. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0217_A0217M-22. the ASTM website.
2 4
For ASME Boiler and Pressure V
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A217/A217M − 20 A217/A217M − 22 Endorsed by Manufacturers Standardization Society
of the Valve and Fittings Industry
Endorsed by American Foundrymen’s Society
Used in USDOE-NE Standards
Standard Specification for
Steel Castings, Martensitic Stainless and Alloy, for
Pressure-Containing Parts, Suitable for High-Temperature
1
Service
This standard is issued under the fixed designation A217/A217M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers martensitic stainless steel and alloy steel castings for valves, flanges, fittings, and other
pressure-containing parts (Note 1) intended primarily for high-temperature and corrosive service (Note 2).
1.2 One grade of martensitic stainless steel and nine grades of ferritic alloy steel are covered. Selection will depend on design and
service conditions, mechanical properties, and the high-temperature and corrosion-resistant characteristics (Note 3).
NOTE 1—Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M. Low alloy quench-and-tempered grades
equivalent to Specification A217/A217M grades may be found in both Specifications A352/A352M and A487/A487M.
NOTE 2—The grades covered by this specification represent materials that are generally suitable for assembly with other castings or wrought steel parts
by fusion welding. It is not intended to imply that these grades possess equal degrees of weldability; therefore, it is the responsibility of the purchaser
to establish for himself a suitable welding technique. Since these grades possess varying degrees of suitability for high-temperature and corrosion-resistant
service, it is also the responsibility of the purchaser to determine which grade shall be furnished, due consideration being given to the requirements of
the applicable construction codes.
NOTE 3—The committee formulating this specification has included nine grades of materials that are considered to represent basic types of ferritic alloy
steels suitable for valves, flanges, fittings, and other pressure-containing parts. Additional alloy steels that may better fulfill certain types of service will
be considered for inclusion in this specification by the committee as the need becomes apparent.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in nonconformance with the standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.18
on Castings.
Current edition approved May 1, 2020March 1, 2022. Published May 2020March 2022. Originally approved in 1939. Last previous edition approved in 20142020 as
A217/A217M – 14.A217/A217M – 20. DOI: 10.1520/A0217_A0217M-20.10.1520/A0217_A0217M-22.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-217/SA 217M in Section II of that code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A217/A217M − 22
2. Referenced Documents
3
2.1 ASTM Standards:
A216/A216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service
A352/A352M Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-
Temperature Service
A487/A487M Specification for Steel Castings Suitable for Pressure Service
A488/A488M Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel
A703/A703M Specification for Steel Castings, General Requ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.