ASTM B409-06
(Specification)Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
SCOPE
1.1 This specification covers UNS N08120, UNS N08890, UNS N08800, UNS N08810, and UNS N08811* in the form of rolled plate, sheet, and strip. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100F (593C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N08890 are normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 409 – 06
Standard Specification for
1
Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
This standard is issued under the fixed designation B 409; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
2
1.1 This specification covers UNS N08120, UNS N08890, 3.1 Definitions of Terms Specific to This Standard: —The
UNS N08800, UNS N08810, and UNS N08811* in the form of terms given in Table 1 shall apply.
rolled plate, sheet, and strip. Alloy UNS N08800 is normally
4. General Requirements
employed in service temperatures up to and including 1100°F
(593°C). Alloys UNS N08120, UNS N08810, UNS N08811, 4.1 Material furnished under this specification shall con-
form to the applicable requirements of Specification B 906
and UNS N08890 are normally employed in service tempera-
tures above 1100°F (593°C) where resistance to creep and unless otherwise provided herein.
rupture is required, and they are annealed to develop controlled
5. Ordering Information
grain size for optimum properties in this temperature range.
5.1 It is the responsibility of the purchaser to specify all
1.2 The values stated in inch-pound units are to be regarded
requirements that are necessary for the safe and satisfactory
as the standard. The values given in parentheses are for
performance of material ordered under this specification.
information only.
Examples of such requirements include but are not limited to
1.3 This standard does not purport to address all of the
the following:
safety concerns, if any, associated with its use. It is the
5.1.1 Alloy (Table 2),
responsibility of the user of this standard to become familiar
5.1.2 Condition (Temper)—Table 3 and Table 4, Appendix
with all hazards including those identified in the appropriate
X1, and Specification B 906.
Material Safety Data Sheet (MSDS) for this product/material
5.1.3 Finish—Appendix X1 and Specification B 906.
as provided by the manufacturer, to establish appropriate
5.1.4 Dimensions—Thickness, width, and length.
safety and health practices, and determine the applicability of
5.1.5 Optional Requirements:
regulatory limitations prior to use.
5.1.5.1 Sheet and Strip—Whether to be furnished in coil, in
2. Referenced Documents
cut straight lengths, or in random straight lengths.
3
2.1 ASTM Standards: 5.1.5.2 Strip—Whethertobefurnishedwithcommercialslit
edge, square edge, or round edge.
B 408 Specification for Nickel-Iron-Chromium Alloy Rod
and Bar 5.1.5.3 Plate—Whether to be furnished specially flattened
(see 9.7.2); also how plate is to be cut (Specification B 906,
B 906 Specification for General Requirements for Flat-
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip Table A3.4 and Table A3.7.
5.1.6 Fabrication Details—Not mandatory but helpful to
the manufacturer:
5.1.6.1 Welding or Brazing—Process to be employed.
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.6.2 Plate—Whether material is to be hot-formed.
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.7 Certification—State if certification or a report of test
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Dec. 1, 2006. Published January 2007. Originally
results is required (Specification B 906).
approved in 1957. Last previous edition approved in 2001 as B 409 – 01.
5.1.8 Samples for Product (Check) Analysis—Whether
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
samples for product (check) analysis should be furnished (see
cation SB 409 in Section II of that Code.
7.2).
* New designations established in accordance with Practice E 527 and SAE
J1086, Practice for Numbering Metals and Alloys (UNS).
5.1.9 Purchaser Inspection—If purchaser wishes to witness
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
tests or inspection of material at place of manufacture, the
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
purchase order must so state indicating which tests or inspec-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tions are to be witnessed (Specification B 906).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B409–06
TABLE 1 Product Description
Product Thickness, in. (mm) Width, in. (mm)
A
3
Hot-rolled plate ⁄16 and over (B 906, Table A3.1 and (B 906,
B
Table A3.2) Table A3.4)
A
Hot-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (B 906, (B 906,
Tab
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.