ASTM B409-06e1
(Specification)Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
SCOPE
1.1 This specification covers UNS N08120, UNS N08890, UNS N08800, UNS N08810, and UNS N08811* in the form of rolled plate, sheet, and strip. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100°F (593°C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N08890 are normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: B409 – 06
Standard Specification for
1
Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
This standard is issued under the fixed designation B409; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—An editorial correction was made in 8.4 in October 2007.
1. Scope B906 Specification for General Requirements for Flat-
2 Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
1.1 This specification covers UNS N08120, UNS N08890,
UNS N08800, UNS N08810, and UNS N08811* in the form of
3. Terminology
rolled plate, sheet, and strip. Alloy UNS N08800 is normally
3.1 Definitions of Terms Specific to This Standard: —The
employed in service temperatures up to and including 1100°F
terms given in Table 1 shall apply.
(593°C). Alloys UNS N08120, UNS N08810, UNS N08811,
and UNS N08890 are normally employed in service tempera-
4. General Requirements
tures above 1100°F (593°C) where resistance to creep and
4.1 Material furnished under this specification shall con-
rupture is required, and they are annealed to develop controlled
form to the applicable requirements of Specification B906
grain size for optimum properties in this temperature range.
unless otherwise provided herein.
1.2 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
5. Ordering Information
information only.
5.1 It is the responsibility of the purchaser to specify all
1.3 This standard does not purport to address all of the
requirements that are necessary for the safe and satisfactory
safety concerns, if any, associated with its use. It is the
performance of material ordered under this specification.
responsibility of the user of this standard to become familiar
Examples of such requirements include but are not limited to
with all hazards including those identified in the appropriate
the following:
Material Safety Data Sheet (MSDS) for this product/material
5.1.1 Alloy (Table 2),
as provided by the manufacturer, to establish appropriate
5.1.2 Condition (Temper)—Table 3 and Table 4, Appendix
safety and health practices, and determine the applicability of
X1, and Specification B906.
regulatory limitations prior to use.
5.1.3 Finish—Appendix X1 and Specification B906.
5.1.4 Dimensions—Thickness, width, and length.
2. Referenced Documents
5.1.5 Optional Requirements:
3
2.1 ASTM Standards:
5.1.5.1 Sheet and Strip—Whether to be furnished in coil, in
B408 Specification for Nickel-Iron-Chromium Alloy Rod
cut straight lengths, or in random straight lengths.
and Bar
5.1.5.2 Strip—Whethertobefurnishedwithcommercialslit
edge, square edge, or round edge.
5.1.5.3 Plate—Whether to be furnished specially flattened
1
This specification is under the jurisdiction of ASTM Committee B02 on
(see 9.7.2); also how plate is to be cut (Specification B906,
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Table A3.4 and Table A3.7.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
5.1.6 Fabrication Details—Not mandatory but helpful to
Current edition approved Dec. 1, 2006. Published January 2007. Originally
approved in 1957. Last previous edition approved in 2001 as B409 – 01. DOI:
the manufacturer:
10.1520/B0409-06E01.
5.1.6.1 Welding or Brazing—Process to be employed.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
5.1.6.2 Plate—Whether material is to be hot-formed.
cation SB 409 in Section II of that Code.
5.1.7 Certification—State if certification or a report of test
* New designations established in accordance with Practice E527 and SAE
J1086, Practice for Numbering Metals and Alloys (UNS).
results is required (Specification B906).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.8 Samples for Product (Check) Analysis—Whether
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
samples for product (check) analysis should be furnished (see
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 7.2).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
´1
B409 – 06
TABLE 1 Product Description
Product Thickness, in. (mm) Width, in. (mm)
A
3
Hot-rolled plate ⁄16 and over (B906, Table A3.1 and (B906,
B
Table A3.2) Table A3.4)
A
Hot-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (B906, (B906, Table A3.6)
Table A3.3)
C
Cold-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (B906, (B906, Table A3.6)
Table A3.3)
C
Cold-rolled strip 0.005 to 0.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.