iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2513-07b

(Specification)

Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings

Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings

SCOPE
1.1 This specification covers requirements and test methods for material (see Appendix X1 ) dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of plastic pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The annexes provide specific requirements and test methods for each of the materials currently approved. If and when additional materials are available, specific annex requirements will be added. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are covered in Annex A1 .
1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X2 . In-plant quality control programs are specified in Annex A3 and Annex A4 .
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
1.4 The following is an index of the annexes and appendixes in this specification:Annex Subject Polyethylene (PE) Pipe and Fittings Poly (Vinyl Chloride) (PVC) Pipe and Fittings for Maintenance or Repair In-Plant Quality Control for all materials up to 12 in. In-Plant Quality Control for PE materials between 14 and 24 in.Polyamide (PA) Pipe and Fittings Magnetic-detectable Polyethylene PipeCrosslinked Polyethylene (PEX) PipePeelable PE PipeAppendixesSubject New MaterialsDesign Consideration Gas Pressure Pipe and Fittings Produced from Polyethylene (PE) materials with Minimum Required Strength (MRS) Designation
1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE: ^ASTMGRP: ASTM Standards: 2.1.1 Terminology:2.1.2Test Methods for:2.1.3Practices for:^REFDOCID: D1898^REFDOCTITLE: Sampling of Plastics 2.1.4Specification for:^REFDOCID: D2740^REFDOCTITLE: Specification for Polyvinyl Chloride (PVC) Plastic Tubing^REFGRP: ANSI Standards:^REFDOCID: B16.40^REFDOCTITLE: Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems^REFDOCID: B31.8^REFDOCTITLE: Gas Transmission and Distribution Piping Systems^REFGRP: Federal Specifications:^REFDOCID: Fed. Std. No. 123^REFDOCTITLE: Marking for Shipment (Civil Agencies)^REFDOCID: OPS 49 CFR Part 192^REFDOCTITLE: Title 49, Code of Federal Regulations^REFGRP: Military Standards:^REFDOCID: MIL-STD-129^REFDOCTITLE: Marking for Shipment and Storage^REFDOCID: MIL-STD-1235^REFDOCTITLE: (ORD) Single- and Multi-Level Continuous Sampling Procedures and Tables for Inspection by Attributes^REFGRP: ISO Standards:^REFDOCID: ISO 4437^REFDOCTITLE: Buried polyethylene (PE) pipes for the supply of gaseous fuels-Metric series-Specifications^REFDOCID: ISO 11922-1^REFDOCTITLE: Thermoplastics pipes for the conveyance of fluids-Dimensions and tolerances -Part 1: Metric series^REFDOCID: ISO 17454^REFDOCTITLE: Plastics piping systems - multilayer pipe - test method for the adhesion of the different layers using a pulling rig.^REFDOCID: ISO 9080^REFDOCTITLE: Thermoplastics Pipes for the Transport of Fluids-Methods of Extrapolation of Hydrostatic Stress Rupture Data to Determine Long-Term Hydrostatic Strength of Thermoplastic Pipe Materials^REFDOCID: ISO 12162^REFDOCTITLE: Thermoplastic Materials for Pipes and Fittings for Pressure Appl...

General Information

Status
Historical
Publication Date
14-Nov-2007
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
F17 - Plastic Piping Systems
Drafting Committee
F17.60 - Gas
Current Stage
Ref Project

Relations

Replaces
ASTM D2513-07a - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
Effective Date
15-Nov-2007
Replaced By
ASTM D2513-07be1 - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
Effective Date
15-Nov-2007
Referred By
ASTM F2620-20ae2 - Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
Effective Date
15-Nov-2007
Referred By
ASTM F1804-21 - Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
Effective Date
15-Nov-2007
Referred By
ASTM F3565-23 - Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service
Effective Date
15-Nov-2007
Referred By
ASTM F2897-23 - Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
Effective Date
15-Nov-2007
Referred By
ASTM F3508-21a - Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
Effective Date
15-Nov-2007
Referred By
ASTM F2619/F2619M-20 - Standard Specification for High-Density Polyethylene (PE) Line Pipe
Effective Date
15-Nov-2007
Referred By
ASTM F905-04(2022) - Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
Effective Date
15-Nov-2007
Referred By
ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
Effective Date
15-Nov-2007
Referred By
ASTM F2206-19 - Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
Effective Date
15-Nov-2007
Referred By
ASTM F1962-22 - Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
Effective Date
15-Nov-2007
Referred By
ASTM F1563-01(2019) - Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
Effective Date
15-Nov-2007
Referred By
ASTM F1924-19 - Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
Effective Date
15-Nov-2007
Referred By
ASTM F1055-16a(2022) - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
Effective Date
15-Nov-2007

Buy Standard

ASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and FittingsASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
PreviousNext
Technical specification
ASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
English language
27 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and FittingsREDLINE ASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
PreviousNext
Technical specification
REDLINE ASTM D2513-07b - Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
English language
27 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: D 2513 – 07b
Standard Specification for
1
Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
This standard is issued under the fixed designation D2513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 1.5 The following precautionary caveat pertains only to the
test method portion, Section 6, of this specification. This
1.1 This specification covers requirements and test methods
standard does not purport to address all of the safety concerns,
for material (see Appendix X1) dimensions and tolerances,
if any, associated with its use. It is the responsibility of the user
hydrostatic burst strength, chemical resistance, and impact
of this standard to establish appropriate safety and health
resistanceofplasticpipe,tubing,andfittingsforuseinfuelgas
practices and determine the applicability of regulatory limita-
mains and services for direct burial and reliner applications.
tions prior to use.
The annexes provide specific requirements and test methods
for each of the materials currently approved. If and when
2. Referenced Documents
additional materials are available, specific annex requirements
2
2.1 ASTM Standards:
will be added. The pipe and fittings covered by this specifica-
2.1.1 Terminology:
tion are intended for use in the distribution of natural gas.
D1600 Terminology for Abbreviated Terms Relating to
Requirements for the qualifying of polyethylene systems for
Plastics
use with liquefied petroleum gas are covered in Annex A1.
F412 Terminology Relating to Plastic Piping Systems
1.1.1 This specification does not cover threaded pipe. De-
2.1.2 Test Methods for:
sign considerations are discussed in Appendix X2. In-plant
D638 Test Method for Tensile Properties of Plastics
quality control programs are specified inAnnexA3 andAnnex
D789 Test Methods for Determination of Solution Viscosi-
A4.
ties of Polyamide (PA)
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
D792 Test Methods for Density and Specific Gravity (Rela-
and appendixes which provide explanatory material. These
tive Density) of Plastics by Displacement
notesandfootnotes(excludingthoseintablesandfigures)shall
D1238 Test Method for Melt Flow Rates ofThermoplastics
not be considered as requirements of the specification.
by Extrusion Plastometer
1.3 The values stated in inch-pound units are to be regarded
D1505 Test Method for Density of Plastics by the Density-
as the standard. The values given in parentheses are provided
Gradient Technique
for information purposes only.
D1598 Test Method for Time-to-Failure of Plastic Pipe
1.4 Thefollowingisanindexoftheannexesandappendixes
Under Constant Internal Pressure
in this specification:
D1599 TestMethodforResistancetoShort-TimeHydraulic
Annex Subject
Pressure of Plastic Pipe, Tubing, and Fittings
Annex A1 Polyethylene (PE) Pipe and Fittings
Annex A2 Poly (Vinyl Chloride) (PVC) Pipe and Fittings for Maintenance or
D2122 Test Method for Determining Dimensions of Ther-
Repair
moplastic Pipe and Fittings
Annex A3 In-Plant Quality Control for all materials up to 12 in.
D2152 Test Method for Adequacy of Fusion of Extruded
Annex A4 In-Plant Quality Control for PE materials between 14 and 24 in.
Annex A5 Polyamide (PA) Pipe and Fittings
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
Annex A6 Magnetic-detectable Polyethylene Pipe
Acetone Immersion
Annex A7 Crosslinked Polyethylene (PEX) Pipe
D2290 Test Method forApparent Hoop Tensile Strength of
Annex A8 Peelable PE Pipe
Plastic or Reinforced Plastic Pipe
Appendixes Subject
D2412 Test Method for Determination of External Loading
Appendix X1 New Materials
Characteristics of Plastic Pipe by Parallel-Plate Loading
Appendix X2 Design Consideration
Appendix X3 Gas Pressure Pipe and Fittings Produced from Polyethylene (PE)
D2444 Test Method for Determination of the Impact Resis-
materials with Minimum Required Strength (MRS) Designation
tance of Thermoplastic Pipe and Fittings by Means of a
1 2
This specification is under the jurisdiction ofASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved Nov. 15, 2007. Published December 2007. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1966. Last previous edition approved in 2007 as D2513–07a. the ASTM website.
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D2513–07a Designation: D 2513 – 07b
Standard Specification for
1
Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
This standard is issued under the fixed designation D2513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers requirements and test methods for material (see Appendix X1) dimensions and tolerances,
hydrostatic burst strength, chemical resistance, and impact resistance of plastic pipe, tubing, and fittings for use in fuel gas mains
and services for direct burial and reliner applications. The annexes provide specific requirements and test methods for each of the
materials currently approved. If and when additional materials are available, specific annex requirements will be added. The pipe
and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying
of polyethylene systems for use with liquefied petroleum gas are covered in Annex A1.
1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X2. In-plant quality
control programs are specified in Annex A3 and Annex A4.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for
information purposes only.
1.4 The following is an index of the annexes and appendixes in this specification:
Annex Subject A1
Annex Subject
Annex A1 Polyethylene (PE) Pipe and Fittings A2
Annex A1 Polyethylene (PE) Pipe and Fittings
Annex A2 Poly (Vinyl Chloride) (PVC) Pipe and Fittings for Maintenance or
Repair A3
Annex A2 Poly (Vinyl Chloride) (PVC) Pipe and Fittings for Maintenance or
Repair
Annex A3 In-Plant Quality Control for all materials up to 12 in. A4
Annex A3 In-Plant Quality Control for all materials up to 12 in.
Annex A4 In-Plant Quality Control for PE materials between 14 and 24 in. A5
Annex A4 In-Plant Quality Control for PE materials between 14 and 24 in.
Annex A5 Polyamide (PA) Pipe and Fittings A6
Annex A5 Polyamide (PA) Pipe and Fittings
Annex A6 Magnetic-detectable Polyethylene Pipe A7
Annex A6 Magnetic-detectable Polyethylene Pipe
Annex A7 Crosslinked Polyethylene (PEX) Pipe
Annex A8 Peelable PE Pipe
Appendixes Subject X1
Appendixes Subject
Appendix X1 New Materials X2
Appendix X1 New Materials
Appendix X2 Design Consideration X3
Appendix X2 Design Consideration
Appendix X3 Gas Pressure Pipe and Fittings Produced from Polyethylene (PE)
materials with Minimum Required Strength (MRS) Designation
1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved May 1,Nov. 15, 2007. Published JuneDecember 2007. Originally approved in 1966. Last previous edition approved in 2007 as D2513–07a.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 2513 – 07b
2. Referenced Documents
2
2.1 ASTM Standards:
2.1.1 Terminology:
D1600 Terminology for Abbreviated Terms Relating to Plastics
F412 Terminology Relating to Plastic Piping Systems
2.1.2 Test Methods for:
D638 Test Method for Tensile Properties of Plastics
D789 Test Methods for Determination of Solution Viscosities of Polyamide (PA)
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of P
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2152-23(Test Method)
Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

SIGNIFICANCE AND USE
3.1 This test method is applicable only for distinguishing between inadequately fused and adequately fused PVC. The difference between thermally degraded and adequately fused PVC cannot be detected by this test method. Acetone immersion testing is not a substitute for burst, impact, or other physical or chemical tests on PVC pipe or fittings and it, therefore, shall not be used as the only test specification for purchasing of PVC pipe and fittings. This test method only detects inadequate fusion and does not determine the over-all quality of the PVC pipe or fittings.  
3.2 This test method is useful in determining whether inadequate fusion contributed to failure of PVC pipe or fittings in other physical or chemical tests, or in service.  
3.3 This test method is useful in evaluating the adequacy of PVC fusion obtained in process or materials trials.  
3.4 This test method determines adequacy of fusion on a single, relatively small specimen. This test method requires the use of a hazardous reagent which must be properly handled and disposed. Therefore, this test method may not be cost-effective to employ as a routine quality control test.
SCOPE
1.1 This test method covers the determination of the adequacy of fusion of extruded rigid poly(vinyl chloride) (PVC) pipe and molded fittings as indicated by reaction to immersion in anhydrous acetone.  
1.2 The values stated in inch-pound units are to be regarded as the standard except where instruments are calibrated in SI units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazards statements are given in Annex A1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2945-18(2023)(Specification)
Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

ABSTRACT
This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas piping. The pipe and fittings covered by this specification are intended for use in the transport of fuel gases. This specification does not cover threaded pipe. The polyamide 11 material used to make pipe and fittings shall be virgin or reworked material and shall have a Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating as determined per PPI TR3 and PPI TR4. This specification deals with requirements for materials, requirements for pipe and fittings, test methods, marking, and quality Assurance.
SCOPE
1.1 This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines. The pipe and fittings covered by this specification are intended for use in the distribution and transmission of fuel gases.  
1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: Heat fusion joining of PA11 pipe and fittings meeting the requirements of this standard is limited to PA11 pipe and fittings meeting the requirements of this standard. Heat Fusion joining of PA11 pipe and fittings meeting the requirements of this standard is not allowed to pipes and fittings made from any other thermoplastic materials (for example, PA12, PEs, PVCs, etc.).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes and appendixes in this specification:    
Annexes  
Subject  
Annex A1  
In-Plant Quality Control for sizes up to 12 in.  
Annex A2  
PA-11 Butt Fusion Fittings  
Appendixes  
Subject  
Appendix X1  
Butt Fusion Guidelines for PA-11 Piping  
Appendix X2  
Design Consideration  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM D3034-23(Specification)
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings. The pipe and fittings shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects. The socket diameters, socket depth, wall thickness, pipe flattening, impact resistance, pipe stiffness, joint tightness, and extrusion quality shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings.  
1.2 Pipe and fittings produced to this specification should be installed in accordance with Practice D2321.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F2817-13(2023)(Specification)
Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair

SCOPE
1.1 This specification covers requirements for PVC pipe and tubing for use only to maintain or repair existing PVC gas piping. This specification covers requirements for fittings for use to maintain or repair existing PVC gas piping.  
1.1.1 In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes and, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes in this specification:    
Annex  
Subject  
Annex A1  
In-Plant Quality Control for PVC materials
up to 6 in.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2928-18(2023)(Practice)
Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods

SIGNIFICANCE AND USE
5.1 This practice provides requirements for standardized preparation of sample butt fusions, preparation of specimens from sample butt fusions, and conditioning for testing in accordance with Test Method D638, Test Method D1598, or Test Method D1599. This practice is intended to improve the ability to reliably compare test results from multiple parties.
SCOPE
1.1 This practice provides standardized sample butt fusion preparation, conditioning, and testing conditions for tension testing of specimens prepared from sample butt fusion joints or hydrostatic tests of sample butt fusion joints in accordance with:  
1.1.1 Test Method D638, tension testing;
1.1.1.1 The preparation or use of tensile specimens other than Test Method D638 Type I through Type V is beyond the scope of this practice.  
1.1.2 Test Method D1598, constant (sustained) hydraulic pressure testing;  
1.1.3 Test Method D1599, short-term hydraulic pressure testing.  
1.1.4 It is not within the scope of this practice to include plastic materials other than polyethylene or other tests for butt fusions. The exclusion of other plastic materials and other tests does not imply that other plastic materials are suitable or unsuitable for butt fusion, or that the tests cited herein are adequate or inadequate for qualitative characterization and for research and development of butt fusion joints, or that other tests do not have lesser, equal, or greater utility for such purpose.  
1.1.5 The evaluation of test results and the determination of test result evaluation criteria are not within the scope of this practice. This practice is limited to standardized butt fusion test specimens and testing conditions for the comparison of test data from multiple parties.  
1.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.1.7 In this standard, text in parentheses, notes in the body of the standard and appendices are informational and non-mandatory. For tables in the body of the standard, table notes are mandatory.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2122-22(Test Method)
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

SIGNIFICANCE AND USE
5.1 This test method provides for determining the physical dimensions of thermoplastic pipe and fittings. This test method is suitable for determination of dimensional compliance with product specifications.
SCOPE
1.1 This test method covers the determination of diameter, wall thickness, and length dimensions of thermoplastic pipe. Included are procedures for measurement of the inside diameter of pipe intended to be joined by internal fittings, measurement of the average outside diameter for roundable pipe where out-of-roundness is not of primary concern, out-of-roundness measurement and measurement of the average outside diameter of non-roundable pipe, and for determining length and straightness.  
1.2 This test method also includes procedures for dimensioning molded thermoplastic pipe fittings.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F409-22(Specification)
Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

ABSTRACT
This specification covers the material, dimensional ,and performance requirements and associated test methods for thermoplastic tubes and fittings for accessible and replaceable domestic waste connections. The tubes, fittings and mechanical joint components shall be made of either virgin acrylonitrile-butadiene-styrene (ABS) plastic, virgin poly(vinyl chloride) (PVC) plastic, or virgin polypropylene plastic. When evaluated by the test procedures provided herein, the products shall adhere to requirements stipulated for hydrostatic pressure, axial stress, joint integrity, and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections. Marking requirements are also included. Thermoplastic that does not meet the material requirements specified in Section 5 is excluded.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    16 pages
    English language
    sale 15% off
  • Technical specification
    16 pages
    English language
    sale 15% off
ASTM
ASTM D2729-21(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly (vinyl chloride) (PVC) sewer and drain pipe and fittings. The pipe shall be made from virgin cell 12164 with a certain minimum tensile strength, 12454 or 12454 poly(vinyl chloride) compounds. The fittings shall be made from virgin poly(vinyl chloride) compounds of cell classification PVC 12454, PVC 12454, or PVC 13343. Compounds that have different cell classification because one or more properties are superior to those of the specified compounds are also acceptable. In order to determine the overall performance of the pipes and fittings, the following tests shall be done: flattening test, joint tightness test, and perforation test. The pipe and fittings shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects. The pipe shall be as uniform as commercially practical in color, opacity, density, and other physical properties.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly(vinyl chloride) (PVC) sewer and drain pipe and fittings. Perforated pipe is also covered; the joint tightness test is not applicable for perforated pipe. A form of marking to indicate compliance with this specification is also included.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2390-21(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content

ABSTRACT
This specification covers the basic requirements and corresponding test methods for poly(vinyl chloride) (PVC) plastic drain, waste, and vent (DWV) pipes and fittings that contain a uniform blend of virgin PVC compound and post-industrial recycle material. When evaluated by the test procedures provided herein, the pipes and fittings shall conform to specified values of the following requirements: dimensions; pipe stiffness, deflection load, lower confidence limit, and flattening resistance; crush resistance; impact resistance; hydrostatic burst resistance; and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent (DWV) pipe and fittings.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2929-17(2021)(Specification)
Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig

ABSTRACT
This specification establishes the requirements for 0.070 in. wall thickness crosslinked polyethylene (PEX) tubing that is outside diameter controlled, and intended for non-potable radiant heating applications for pressures up to 75 psig. It covers requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, bent-tube hydrostatic pressure, environmental stress cracking, stabilizer functionality, excessive temperature and degree of crosslinking, as well as requirements for tubing markings.
SCOPE
1.1 This specification covers 0.070 in. wall thickness crosslinked polyethylene (PEX) tubing that is outside diameter controlled, and intended for non-potable radiant heating applications for pressures up to 75 psig in sizes 5/8 NTS (nominal tubing size) and 7/8 NTS. This specification also includes fittings that are specifically designed for this 0.070 in.-wall PEX tubing. Only maximum 75-psig relief valves shall be used with this tubing. Included in this specification are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, environmental stress cracking, stabilizer functionality, bent-tube hydrostatic pressure, excessive temperature and degree of crosslinking. Requirements for tubing markings are also given. This specification incorporates an optional middle or outer oxygen barrier layer. This tubing is not intended for field bending at temperatures above 120 ºF (49 ºC).  
1.2 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off