ASTM D3350-10

Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

ABSTRACT
This specification covers the identification of polyethylene plastic pipe and fitting materials. Cell classification of materials shall be according to tests of primary properties like density, melt index, flexural modulus, tensile strength at yield, slow crack growth resistance, and hydrostatic strength classification. Materials shall be manufactured by molding and extrusion of polyethylene plastic in the form of powder, granules, or pellets. Color and ultraviolet stabilizer, thermal stability, brittleness temperature, density, tensile strength at yield, and elongation at break shall conform to this specification.
SCOPE
1.1 This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing tolerances, or to determine suitability for use for a specific application.
1.2 Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 2). This specification allows for the use of those polyethylene materials, provided that all specific requirements of this specification are met.
Note 1—The notes in this specification are for information only and shall not be considered part of this specification.
Note 2—See Guide D5033 for information and definitions related to recycled plastics.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 3—There is no known ISO equivalent to this standard.  
1.5 For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and cable materials see Specification D1248.

General Information

• Status: Historical
• Publication Date: 31-Dec-2009
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Relations

• Replaces: ASTM D3350-08 - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
• Effective Date: 01-Jan-2010
• Replaced By: ASTM D3350-10a - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
• Effective Date: 15-Nov-2010
• Referred By: ASTM F2021-17(2022) - Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems
• Effective Date: 01-Jan-2010
• Referred By: ASTM D2239-22 - Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
• Effective Date: 01-Jan-2010
• Referred By: ASTM F667/F667M-16(2021) - Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
• Effective Date: 01-Jan-2010
• Referred By: ASTM F2720/F2720M-20 - Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe
• Effective Date: 01-Jan-2010
• Referred By: ASTM F2435-22 - Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe
• Effective Date: 01-Jan-2010
• Referred By: ASTM E1858-23 - Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry
• Effective Date: 01-Jan-2010
• Referred By: ASTM F1759-97(2018) - Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
• Effective Date: 01-Jan-2010
• Referred By: ASTM D2683-20 - Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
• Effective Date: 01-Jan-2010
• Referred By: ASTM D3485-22 - Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)
• Effective Date: 01-Jan-2010
• Referred By: ASTM E2009-23 - Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
• Effective Date: 01-Jan-2010
• Referred By: ASTM F2896-23 - Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
• Effective Date: 01-Jan-2010
• Referred By: ASTM F1545-15a(2021) - Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
• Effective Date: 01-Jan-2010
• Referred By: ASTM D1248-16 - Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
• Effective Date: 01-Jan-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3350 – 10
Standard Specification for
1
Polyethylene Plastics Pipe and Fittings Materials
This standard is issued under the fixed designation D3350; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* and Elastomers by Impact
D790 Test Methods for Flexural Properties of Unreinforced
1.1 This specification covers the identification of polyeth-
andReinforcedPlasticsandElectricalInsulatingMaterials
ylene plastic pipe and fittings materials in accordance with a
D792 Test Methods for Density and Specific Gravity (Rela-
cell classification system. It is not the function of this specifi-
tive Density) of Plastics by Displacement
cationtoprovidespecificengineeringdatafordesignpurposes,
D883 Terminology Relating to Plastics
tospecifymanufacturingtolerances,ortodeterminesuitability
D1238 Test Method for Melt Flow Rates ofThermoplastics
for use for a specific application.
by Extrusion Plastometer
1.2 Polyethylene plastic materials, being thermoplastic, are
D1248 Specification for Polyethylene Plastics Extrusion
reprocessable and recyclable (Note 2). This specification al-
Materials for Wire and Cable
lows for the use of those polyethylene materials, provided that
D1505 Test Method for Density of Plastics by the Density-
all specific requirements of this specification are met.
Gradient Technique
NOTE 1—The notes in this specification are for information only and
D1603 Test Method for Carbon Black Content in Olefin
shall not be considered part of this specification.
Plastics
NOTE 2—See Guide D5033 for information and definitions related to
D1693 Test Method for Environmental Stress-Cracking of
recycled plastics.
Ethylene Plastics
1.3 The values stated in SI units are to be regarded as
3
D1898 Practice for Sampling of Plastics
standard.
D2837 TestMethodforObtainingHydrostaticDesignBasis
1.4 This standard does not purport to address all of the
forThermoplasticPipeMaterialsorPressureDesignBasis
safety concerns, if any, associated with its use. It is the
for Thermoplastic Pipe Products
responsibility of the user of this standard to establish appro-
D2839 Practice for Use of a Melt Index Strand for Deter-
priate safety and health practices and determine the applica-
mining Density of Polyethylene
bility of regulatory limitations prior to use.
D3892 Practice for Packaging/Packing of Plastics
NOTE 3—There is no known ISO equivalent to this standard. D4218 Test Method for Determination of Carbon Black
Content in Polyethylene Compounds By the Muffle-
1.5 For information regarding molding and extrusion mate-
Furnace Technique
rials see Specification D4976. For information regarding wire
D4703 Practice for Compression Molding Thermoplastic
and cable materials see Specification D1248.
Materials into Test Specimens, Plaques, or Sheets
D4883 Test Method for Density of Polyethylene by the
2. Referenced Documents
2 Ultrasound Technique
2.1 ASTM Standards:
D4976 Specification for Polyethylene Plastics Molding and
D618 Practice for Conditioning Plastics for Testing
Extrusion Materials
D638 Test Method for Tensile Properties of Plastics
D5033 Guide for Development of ASTM Standards Relat-
D746 Test Method for Brittleness Temperature of Plastics
3
ing to Recycling and Use of Recycled Plastics
F1473 Test Method for Notch Tensile Test to Measure the
1
Resistance to Slow Crack Growth of Polyethylene Pipes
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
and Resins
Materials.
2.2 ISO Standard:
Current edition approved Jan. 1, 2010. Published February 2010. Originally
ISO12162 Thermoplastic Materials for Pipes and Fittings
approved in 1974. Last previous edition approved in 2008 as D3350-08. DOI:
10.1520/D3350-10. for Pressure Applications—Classification and
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
3
the ASTM website. Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3350 – 10
Designation—Overall Service (Design) Coefficient 3.3.2 Specification D3350:
3.3.2.1 Type(I,II,III)=densityranges(sameasTypesI,II,
3. Terminology
and III in Specification D1248 and Classes 1, 2, and 3 in
3.1 Definitions—Terms as described in Terminology D883
Specification D4976).
shall a
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3350–08 Designation: D3350 – 10
Standard Specification for
1
Polyethylene Plastics Pipe and Fittings Materials
This standard is issued under the fixed designation D3350; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell
classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify
manufacturing tolerances, or to determine suitability for use for a specific application.
1.2 Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 2).This specification allows for
the use of those polyethylene materials, provided that all specific requirements of this specification are met.
NOTE 1—The notes in this specification are for information only and shall not be considered part of this specification.
NOTE 2—See Guide D5033 for information and definitions related to recycled plastics.
1.3 The values stated in SI units are to be regarded as standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE3—There is no similar or equivalent ISO standard. 3—There is no known ISO equivalent to this standard.
1.5 For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and
cable materials see Specification D1248.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D746 Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1603 Test Method for Carbon Black Content in Olefin Plastics
D1693 Test Method for Environmental Stress-Cracking of Ethylene Plastics
3
D1898 Practice for Sampling of Plastics
D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for
Thermoplastic Pipe Products
D2839 Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
D3892 Practice for Packaging/Packing of Plastics
D4218 TestMethodforDeterminationofCarbonBlackContentinPolyethyleneCompoundsBytheMuffle-FurnaceTechnique
D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
D4883 Test Method for Density of Polyethylene by the Ultrasound Technique
D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materials.
Current edition approved AprilJan. 1, 2008.2010. Published May 2008.February 2010. Originally approved in 1974. Last previous edition approved in 20062008 as
D3350-068. DOI: 10.1520/D3350-108.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3350 – 10
D5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics
F1473 Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
2.2 ISO Standard:
ISO12162 ThermoplasticMateria
...