iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D1708-10

(Test Method)

Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

SIGNIFICANCE AND USE
This test method provides data for quality control and acceptance or rejection under specifications.
Before proceeding with this test method, reference should be made to the ASTM specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the materials specification shall take precedence over those mentioned in this test method. If there are no material specifications, then the default conditions herein apply. Table 1 of Classification System D4000 lists the ASTM materials standards that currently exist.
SCOPE
1.1 This test method covers certain material specifications for which a history of data has been obtained using the standard microtensile specimen. The specimen geometry has been changed to be equivalent to that of ISO 12086-2:1995. In general, this test method is superseded for general use by either Test Methods D882 or Test Method D638. The very small Type V specimen in Test Method D638 is the recommended specimen when limited amounts of material are available.
1.2 This test method covers the determination of the comparative tensile strength and elongation properties of plastics in the form of standard microtensile test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. It can be used for specimens of any thickness up to 3.2 mm (1/8 in.), including thin films.
1.3 This test method cannot be used for the determination of modulus of elasticity. For the determination of modulus, see Test Method D638 or Test Methods D882.
1.4 Test data obtained by this test method are relevant and appropriate for use in engineering design.
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this standard.

General Information

Status
Historical
Publication Date
31-Mar-2010
ICS
83.080.01 - Plastics in general
Technical Committee
D20 - Plastics
Drafting Committee
D20.10 - Mechanical Properties
Current Stage
Ref Project

Relations

Replaces
ASTM D1708-06a - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
Effective Date
01-Apr-2010
Replaced By
ASTM D1708-13 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
Effective Date
01-Sep-2013
Referred By
ASTM D4745-19 - Standard Classification System and Basis for Specification for Filled Polytetrafluoroethlyene (PTFE) Molding and Extrusion Materials Using ASTM Methods
Effective Date
01-Apr-2010
Referred By
ASTM D3307-21 - Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
Effective Date
01-Apr-2010
Referred By
ASTM D6456-10(2018) - Standard Specification for Finished Parts Made from Polyimide Resin
Effective Date
01-Apr-2010
Referred By
ASTM F3510-21 - Standard Guide for Characterizing Fiber-Based Constructs for Tissue-Engineered Medical Products
Effective Date
01-Apr-2010
Referred By
ASTM D3295-20 - Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing
Effective Date
01-Apr-2010
Referred By
ASTM D4895-18(2023) - Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion
Effective Date
01-Apr-2010
Referred By
ASTM D7194-19 - Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)
Effective Date
01-Apr-2010
Referred By
ASTM D4894-19 - Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
Effective Date
01-Apr-2010
Referred By
ASTM G21-15(2021)e1 - Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
Effective Date
01-Apr-2010
Referred By
ASTM G114-21 - Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
Effective Date
01-Apr-2010
Referred By
ASTM F561-19 - Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids
Effective Date
01-Apr-2010
Referred By
ASTM D7292-18 - Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI)
Effective Date
01-Apr-2010
Referred By
ASTM D3275-18(2023) - Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
Effective Date
01-Apr-2010

Buy Standard

ASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile SpecimensASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
PreviousNext
Standard
ASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile SpecimensREDLINE ASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
PreviousNext
Standard
REDLINE ASTM D1708-10 - Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1708 − 10
StandardTest Method for
Tensile Properties of Plastics by Use of Microtensile
1
Specimens
This standard is issued under the fixed designation D1708; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This test method covers certain material specifications 2.1 ASTM Standards:
forwhichahistoryofdatahasbeenobtainedusingthestandard D618 Practice for Conditioning Plastics for Testing
microtensile specimen. The specimen geometry has been D638 Test Method for Tensile Properties of Plastics
changed to be equivalent to that of ISO 12086-2:1995. In D882 Test Method for Tensile Properties of Thin Plastic
general,thistestmethodissupersededforgeneralusebyeither Sheeting
TestMethodsD882orTestMethodD638.TheverysmallType D883 Terminology Relating to Plastics
V specimen in Test Method D638 is the recommended speci- D4000 Classification System for Specifying Plastic Materi-
men when limited amounts of material are available. als
E691 Practice for Conducting an Interlaboratory Study to
1.2 This test method covers the determination of the com-
Determine the Precision of a Test Method
parativetensilestrengthandelongationpropertiesofplasticsin
2.2 ISO Standard:
the form of standard microtensile test specimens when tested
ISO 12086-2:1995 Plastics—Fluoropolymer Dispersion,
under defined conditions of pretreatment, temperature,
Moulding, and Extrusion Materials—Part 2 Preparation of
humidity, and testing machine speed. It can be used for
3
1 Test Specimens and Determination of Properties
specimens of any thickness up to 3.2 mm ( ⁄8 in.), including
thin films.
3. Terminology
1.3 Thistestmethodcannotbeusedforthedeterminationof
3.1 Definitions: Definitions of terms applying to this test
modulus of elasticity. For the determination of modulus, see
method appear in Terminology D883 and Test Method D638,
Test Method D638 or Test Methods D882.
Annex A2.
1.4 Test data obtained by this test method are relevant and
appropriate for use in engineering design.
4. Significance and Use
1.5 The values stated in SI units are to be regarded as
4.1 This test method provides data for quality control and
standard. The values given in parentheses are for information
acceptance or rejection under specifications.
only.
4.2 Before proceeding with this test method, reference
1.6 This standard does not purport to address all of the
should be made to the ASTM specification of the material
safety concerns, if any, associated with its use. It is the
being tested. Any test specimen preparation, conditioning,
responsibility of the user of this standard to establish appro-
dimensions, or testing parameters, or combination thereof,
priate safety and health practices and determine the applica-
covered in the materials specification shall take precedence
bility of regulatory limitations prior to use.
over those mentioned in this test method. If there are no
NOTE 1—There is no known ISO equivalent to this standard.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This test method is under the jurisdiction ofASTM Committee D20 on Plastics contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and is the direct responsibility of Subcommittee D20.10 on Mechanical Properties. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2010. Published April 2010. Originally the ASTM website.
3
approved in 1959. Last previous edition approved in 2006 as D1708 - 06a. DOI: Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
10.1520/D1708-10. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D1708 − 10
material specifications, then the default conditions herein 6. Test Specimens
apply. Table 1 of Classification System D4000 lists theASTM
6.1 Microtensile test specimens shall conform to the dimen-
materials standards that currently exist.
sions shown in Fig. 1. This specimen shall be prepared by
die-cutting or machining from sheet, plate, slab, or finished
5. Apparatus
article. Dimensions of a die suitable for preparing die-cut
specimens are also shown in Fig. 1. Specimens may also be
5.1 The apparatus shall be as specified in Test Method
prepared by injection molding or compress
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D1708–06a Designation:D1708–10
Standard Test Method for
Tensile Properties of Plastics by Use of Microtensile
1
Specimens
This standard is issued under the fixed designation D1708; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This test method covers certain material specifications for which a history of data has been obtained using the standard
microtensilespecimen.ThespecimengeometryhasbeenchangedtobeequivalenttothatofISO12086-2:1995ISO12086-2:1955.
In general, this test method is superseded for general use by either Test Methods D882 or Test Method D638. The very small Type
V specimen in Test Method D638 is the recommended specimen when limited amounts of material are available.
1.2 This test method covers the determination of the comparative tensile strength and elongation properties of plastics in the
form of standard microtensile test specimens when tested under defined conditions of pretreatment, temperature, humidity, and
1
testing machine speed. It can be used for specimens of any thickness up to 3.2 mm [( ⁄8 in.],in.), including thin films.
1.3 This test method cannot be used for the determination of modulus of elasticity. For the determination of modulus, see Test
Method D638 or Test Methods D882.
1.4 Test data obtained by this test method are relevant and appropriate for use in engineering design.
1.5 The values stated in SI units are to be regarded as standard. The values given in bracketsparentheses are for information
only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE1—There is no equivalent or similar ISO standard. 1—There is no known ISO equivalent to this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D883 Terminology Relating to Plastics
D4000 Classification System for Specifying Plastic Materials
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
2.2 ISO Standard:
ISO 12086-2:1995 Plastics—Fluoropolymer Dispersion, Moulding, and Extrusion Materials—Part 2 Preparation of Test
3
Specimens and Determination of Properties
3. Terminology
3.1 Definitions: Definitions of terms applying to this test method appear in Terminology D883 and Test Method D638, Annex
A2.
4. Significance and Use
4.1 This test method provides data for quality control and acceptance or rejection under specifications.
4.2 Before proceeding with this test method, reference should be made to theASTM specification of the material being tested.
1
This test method is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.10 on Mechanical Properties.
Current edition approved Nov.April 1, 2006.2010. Published November 2006.April 2010. Originally approved in 1959. Last previous edition approved in 2006 as
D1708 - 06a. DOI: 10.1520/D1708-06A.10.1520/D1708-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D1708–10
Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the materials
specification shall take precedence over those mentioned in this test method. If there are no material specifications, then the default
conditions herein apply. Table 1 of Classification System D4000 lists the ASTM materials standards that
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5675-13(2023)(Classification)
Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders

ABSTRACT
This classification system provides a method of adequately identifying PTFE micropowders using a system consistent with that also of another specific classification. These powders are sometimes known as lubricant powders which usually have a much smaller particle size than those used for molding or extrusion. The test methods and properties included are those required to identify and specify the various types of fluoropolymer micropowders. This classification covers two groups of fluoropolymer micropowders. Fluoropolymer micropowders are classified into groups according to their base fluoropolymer. These groups are further subdivided into classes and grades. Different tests shall be performed in order to determine the following properties of the micropowders: melting characteristics, melt flow rate, specific gravity, water content, particle size, surface area, and bulk density.
SCOPE
1.1 This classification system provides a method of adequately identifying low molecular weight polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) micronized powders using a system consistent with that of Classification System D4000. It further provides a means for specifying these materials by the use of a simple line callout designation. This classification covers fluoropolymer micronized powders that are used as lubricants and as additives to other materials in order to improve lubricity or to control other characteristics of the base material.  
1.2 These powders are sometimes known as lubricant powders. The powders usually have a much smaller particle size than those used for molding or extrusion, and they generally are not processed alone. The test methods and properties included are those required to identify and specify the various types of fluoropolymer micronized powders. Recycled fluoropolymer materials meeting the detailed requirements of this classification are included (see Guide D7209).  
1.3 These fluoropolymer micronized powders and the materials designated as filler powders (F) in ISO 12086-1 and ISO 12086-2 are equivalent.2  
1.4 The values stated in SI units as detailed in IEEE/ASTM SI-10 are to be regarded as the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.1.2.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1203-23(Test Method)
Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods

SIGNIFICANCE AND USE
4.1 The test methods are intended to be rapid empirical tests which have been found to be useful in the relative comparison of materials having the same nominal thickness.
Note 2: When the plastic material contains plasticizer, loss from the plastic is assumed to be primarily plasticizer. The effect of moisture is considered to be negligible.  
4.2 Correlation with ultimate application for various plastic materials shall be determined by the user.
SCOPE
1.1 These test methods cover the determination of volatile loss from a plastic material under defined conditions of time and temperature, using activated carbon as the immersion medium.  
1.2 Two test methods are covered as follows:  
1.2.1 Test Method A, Direct Contact with Activated Carbon—In this test method the plastic material is in direct contact with the carbon. This test method is particularly useful in the rapid comparison of a large number of plastic specimens.  
1.2.2 Test Method B, Wire Cage—This test method prescribes the use of a wire cage, which prevents direct contact between the plastic material and the carbon. By eliminating the direct contact, the migration of the volatile components to the surrounding carbon is minimized and loss by volatilization is more specifically measured.  
1.3 The values stated in SI units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This standard and ISO 176 address the same subject matter, but differ in technical content.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D883-23(Terminology)
Standard Terminology Relating to Plastics

SCOPE
1.1 This terminology covers definitions of technical terms used in the plastics industry. Terms that are generally understood or adequately defined in other readily available sources are not included.  
1.2 When a term is used in an ASTM document for which Committee D20 is responsible it is included only when judged, after review, by Subcommittee D20.92 to be a generally usable term.  
1.3 Definitions that are identical to those published by another standards body are identified with the abbreviation of the name of the organization; for example, IUPAC is the International Union of Pure and Applied Chemistry.  
1.4 A definition is a single sentence with additional information included in discussion notes.
Note 1: It is recommended that definitions be reviewed periodically.  
1.4.1 When a new definition is added to this terminology standard, or the wording of a definition is revised, the date of the change shall be appended to the new or revised definition.  
1.5 For literature related to plastics terminology, see Appendix X1.  
1.6 Subsections 1.6.1 – 1.6.5 contain references to specific terminology standards that are relevant to specific plastic products or applications. In case of conflict between a definition contained in Terminology D883 and one contained in another standard, the definition given in Terminology D883 shall prevail.  
1.6.1 For terms related to thermal insulation, the applicable definitions are contained in Terminology C168.  
1.6.2 For terms related to electrical or electronic insulating materials, the applicable definitions are contained in Terminology D1711.  
1.6.3 For terms relating to fire, the applicable definitions are contained in Terminology E176 and ISO 13943. In case of conflict between Terminology E176 and ISO 13943, the definitions given in Terminology E176 shall prevail.  
1.6.4 For terms relating to precision and bias and associated issues, the applicable definitions are contained in Terminology E456.  
1.6.5 For terms related to plastic piping systems, the applicable definitions are contained in Terminology F412.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D3763-23(Test Method)
Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors

SIGNIFICANCE AND USE
4.1 This test method is designed to provide load versus deformation response of plastics under essentially multi-axial deformation conditions at impact velocities. This test method further provides a measure of the rate sensitivity of the material to impact.  
4.2 Multi-axial impact response, while partly dependent on thickness, does not necessarily have a linear correlation with specimen thickness. Therefore, results must be compared only for specimens of essentially the same thickness, unless specific responses versus thickness formulae have been established for the material.  
4.3 For many materials, there are cases where a specification that requires the use of this test method, but with some procedural modifications that take precedence when adhering to the specification. Therefore, it is advisable to refer to that material specification before using this test method. Table 1 of Classification System D4000 lists the ASTM materials standards that currently exist.
SCOPE
1.1 This test method covers the determination of puncture properties of rigid plastics over a range of test velocities.  
1.2 Test data obtained by this test method are relevant and appropriate for use in engineering design.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This standard and ISO 6603-2 address the same subject matter, but differ in technical content. The technical content and results shall not be compared between the two test methods.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D5023-23(Test Method)
Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)

SIGNIFICANCE AND USE
5.1 This test method provides a simple means of characterizing the thermomechanical behavior of plastic compositions using very small amounts of material. The data obtained is used for quality control, research and development as well as the establishment of optimum processing conditions.  
5.2 Dynamic mechanical testing provides a sensitive means for determining thermomechanical characteristics by measuring the elastic and loss moduli as a function of frequency, temperature, or time. Plots of moduli and tan delta of a material versus these variables can be used to provide a graphical representation indicative of functional properties, effectiveness of cure (thermosetting resin system), and damping behavior under specified conditions.  
5.2.1 Observed data are specific to experimental conditions. Reporting in full (as described in this test method) the conditions under which the data was obtained is essential to assist users with interpreting the data an reconciling apparent or perceived discrepancies.  
5.3 This test method can be used to assess:  
5.3.1 Modulus as a function of temperature,  
5.3.2 Modulus as a function of frequency,  
5.3.3 The effects of processing treatment,  
5.3.4 Relative resin behavioral properties, including cure and damping.  
5.3.5 The effects of substrate types and orientation (fabrication) on modulus,  
5.3.6 The effects of formulation additives which might affect processability or performance,  
5.3.7 The effects of annealing on modulus and glass transition temperature,  
5.3.8 The effect of aspect ratio on the modulus of fiber reinforcements, and  
5.3.9 The effect of fillers, additives on modulus and glass transition temperature.  
5.4 Before proceeding with this test method, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM materials specification shall take precedence over those m...
SCOPE
1.1 This test method outlines the use of dynamic mechanical instrumentation for determining and reporting the visco-elastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular bars molded directly or cut from sheets, plates, or molded shapes. The data generated, using three-point bending techniques, is used to identify the thermomechanical properties of a plastic material or compositions using a variety of dynamic mechanical instruments.  
1.2 This test method is intended to provide means for determining the viscoelastic properties of a wide variety of plastics materials using nonresonant, forced-vibration techniques in accordance with Practice D4065. Plots of the elastic (storage) modulus; loss (viscous) modulus; complex modulus and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of polymeric material systems.  
1.3 This test method is valid for a wide range of frequencies, typically from 0.01 Hz to 100 Hz.  
1.4 Due to possible instrumentation compliance, the data generated are intended to indicate relative and not necessarily absolute property values.  
1.5 Test data obtained by this test method are relevant and appropriate for use in engineering design.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This test method is equivalent to ISO 6721, Part 5.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established ...

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5024-23(Test Method)
Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression

SIGNIFICANCE AND USE
5.1 This test method provides a simple means of characterizing the thermomechanical behavior of plastic compositions using very small amounts of material. The data obtained can be used for quality control and/or research and development purposes. For some classes of materials, such as thermosets, it can also be used to establish optimum processing conditions.  
5.2 Dynamic mechanical testing provides a sensitive method for determining thermomechanical characteristics by measuring the elastic and loss moduli as a function of frequency, temperature, or time. Plots of moduli and tan delta of a material versus these variables provide graphical representation indicative of functional properties, effectiveness of cure (thermosetting resin system), and damping behavior under specified conditions.  
5.2.1 Observed data are specific to experimental conditions. Reporting in full (as described in this test method) the conditions under which the data was obtained is essential to assist users with interpreting the data an reconciling apparent or perceived discrepancies.  
5.3 This test method can be used to assess:  
5.3.1 Modulus as a function of temperature,  
5.3.2 Modulus as a function of frequency,  
5.3.3 The effects of processing treatment, including orientation,  
5.3.4 Relative resin behavioral properties, including cure and damping,  
5.3.5 The effects of substrate types and orientation (fabrication) on elastic modulus,  
5.3.6 The effects of formulation additives which might affect processability or performance,  
5.3.7 The effects of annealing on modulus and glass transition temperature,  
5.3.8 The effect of aspect ratio on the modulus of fiber reinforcements, and  
5.3.9 The effect of fillers, additives on modulus and glass transition temperature.  
5.4 Before proceeding with this test method, make reference to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination...
SCOPE
1.1 This test method outlines the use of dynamic mechanical instrumentation for determining and reporting the viscoelastic properties of thermoplastic and thermosetting resins as well as composite systems in the form of cylindrical specimens molded directly or cut from sheets, plates, or molded shapes. The compression data generated is used to identify the thermomechanical properties of a plastics material or composition using a variety of dynamic mechanical instruments.  
1.2 This test method is intended to provide a means for determining the thermomechanical properties (as a function of a number of viscoelastic variables) for a wide variety of plastic materials using nonresonant, forced-vibration techniques as outlined in Practice D4065. Plots of the elastic (storage) modulus, loss (viscous) modulus, complex modulus, and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of the polymeric material system.  
1.3 This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz.  
1.4 Due to possible instrumentation compliance, the data generated are intended to indicate relative and not necessarily absolute property values.  
1.5 Test data obtained by this test method are relevant and appropriate for use in engineering design.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.8 This international standard was developed in accordance with internationally recognized pr...

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5026-23(Test Method)
Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension

SIGNIFICANCE AND USE
5.1 This test method provides a simple means of characterizing the thermomechanical behavior of plastic materials using very small amounts of material. The data obtained is used for quality control, research and development, as well as the establishment of optimum processing conditions.  
5.2 Dynamic mechanical testing provides a sensitive method for determining thermomechanical characteristics by measuring the elastic and loss moduli as a function of frequency, temperature, or time. Plots of moduli and tan delta of a material versus these variables can be used to provide graphical representation indicative of functional properties, effectiveness of cure (thermosetting resin system), and damping behavior under specified conditions.  
5.2.1 Observed data are specific to experimental conditions. Reporting in full (as described in this test method) the conditions under which the data was obtained is essential to assist users with interpreting the data an reconciling apparent or perceived discrepancies.  
5.3 This test method can be used to assess:  
5.3.1 Modulus as a function of temperature,  
5.3.2 Modulus as a function of frequency,  
5.3.3 The effects of processing treatment, including orientation,  
5.3.4 Relative resin behavioral properties, including cure and damping,  
5.3.5 The effects of substrate types and orientation (fabrication) on elastic modulus,  
5.3.6 The effects of formulation additives which might affect processability or performance,  
5.3.7 The effects of annealing on modulus and glass transition temperature,  
5.3.8 The effect of aspect ratio on the modulus of fiber reinforcements, and  
5.3.9 The effect of fillers, additives on modulus and glass transition temperature.  
5.4 Before proceeding with this test method, make reference to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM materials specificati...
SCOPE
1.1 This test method outlines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular specimens molded directly or cut from sheets, plates, or molded shapes. The tensile data generated is used to identify the thermomechanical properties of a plastic material or composition using a variety of dynamic mechanical instruments.  
1.2 This test method is intended to provide a means for determining viscoelastic properties of a wide variety of plastic materials using nonresonant forced-vibration techniques, in accordance with Practice D4065. Plots of the elastic (storage) modulus; loss (viscous) modulus; complex modulus and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of the polymeric material system.  
1.3 This test method is valid for a wide range of frequencies, typically from 0.01 Hz to 100 Hz.  
1.4 Due to possible instrumentation compliance, the data generated are intended to indicate relative and not necessarily absolute property values.  
1.5 Test data obtained by this test method are relevant and appropriate for use in engineering design.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This test method is technically equivalent to ISO 6721, Part 4.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Pri...

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2863-23(Test Method)
Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

SIGNIFICANCE AND USE
5.1 This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied.  
5.2 In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method.
SCOPE
1.1 This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen.  
1.2 This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index.  
1.3 Test specimens used for this test method are prepared into one of six types of specimens (see Table 1).    
1.4 This test method provides for testing materials that are structurally self-supporting in the form of vertical bars or sheet up to 10.5-mm thick. Such materials are solid, laminated or cellular materials characterized by an apparent density greater than 15 kg/m3.  
1.5 This test method also provides for testing flexible sheet or film materials, while supported vertically.  
1.6 This test method is also suitable, in some cases, for cellular materials having an apparent density of less than 15 kg/m3.
Note 1: Although this test method has been found applicable for testing some other materials, the precision of the test method has not been determined for these materials, or for specimen geometries and test conditions outside those recommended herein.  
1.7 This test method measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statement are given in Section 10.  
1.10 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
Note 2: This test method and ISO 4589-2 are technically equivalent when using the gas measurement and control device described in 6.3.1, with direct oxygen concentration measurement.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off
ASTM
ASTM D695-23(Test Method)
Standard Test Method for Compressive Properties of Rigid Plastics

SIGNIFICANCE AND USE
4.1 Compression tests provide information about the compressive properties of plastics when employed under conditions approximating those under which the tests are made.  
4.2 Compressive properties include modulus of elasticity, yield stress, deformation beyond yield point, and compressive strength (unless the material merely flattens but does not fracture). Materials possessing a low order of ductility may not exhibit a yield point. In the case of a material that fails in compression by a shattering fracture, the compressive strength has a very definite value. In the case of a material that does not fail in compression by a shattering fracture, the compressive strength is an arbitrary one depending upon the degree of distortion that is regarded as indicating complete failure of the material. Many plastic materials will continue to deform in compression until a flat disk is produced, the compressive stress (nominal) rising steadily in the process, without any well-defined fracture occurring. Compressive strength can have no real meaning in such cases.  
4.3 Compression tests provide a standard method of obtaining data for research and development, quality control, acceptance or rejection under specifications, and special purposes. The tests cannot be considered significant for engineering design in applications differing widely from the load-time scale of the standard test. Such applications require additional tests such as impact, creep, and fatigue.  
4.4 Before proceeding with this test method, reference should be made to the ASTM specification for the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in this test method. If there is no material specification, then the default conditions apply. Table 1 in Classification D4000 lists the ASTM materials standards that currently exist.
SCOPE
1.1 This test method covers the determination of the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading. Test specimens of standard shape are employed. This procedure is applicable for a composite modulus up to and including 41,370 MPa (6,000,000 psi).  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
Note 1: For compressive properties of resin-matrix composites reinforced with oriented continuous, discontinuous, or cross-ply reinforcements, tests may be made in accordance with Test Method D3410/D3410M or D6641/D6641M.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 13.1.
Note 2: This standard is equivalent to ISO 604.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D1929-23(Test Method)
Standard Test Method for Determining Ignition Temperature of Plastics

SIGNIFICANCE AND USE
4.1 Tests made under conditions herein prescribed can be of considerable value in comparing the relative ignition characteristics of different materials. Values obtained represent the lowest ambient air temperature that will cause ignition of the material under the conditions of this test. Test values are expected to rank materials according to ignition susceptibility under actual use conditions.  
4.2 This test is not intended to be the sole criterion for fire hazard. In addition to ignition temperatures, fire hazards include other factors such as burning rate or flame spread, intensity of burning, fuel contribution, products of combustion, and others.
SCOPE
1.1 This fire test response test method2 covers a laboratory determination of the flash ignition temperature and spontaneous ignition temperature of plastics using a hot-air furnace.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 Caution—During the course of combustion, gases or vapors, or both, are evolved that have the potential to be hazardous to personnel.  
1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.5 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 1.3 and 1.4.
Note 1: This test method and ISO 871-2022 (Option 1) are similar in all technical details.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off