ASTM E1119-22e1
(Specification)Standard Specification for Industrial Grade Ethylene Glycol
Standard Specification for Industrial Grade Ethylene Glycol
ABSTRACT
This specification covers industrial grade ethylene glycol. The acidity, appearance, color, glycols, water mass, ash content, distillation range, relative density, and water miscibility shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers industrial grade ethylene glycol.
1.2 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling and safety precautions.
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: E1119 − 22
Standard Specification for
1
Industrial Grade Ethylene Glycol
This standard is issued under the fixed designation E1119; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorial corrections were made to Table 1 in August 2022.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers industrial grade ethylene gly- 2.1 ASTM Standards:
D482 Test Method for Ash from Petroleum Products
col.
D850 Test Method for Distillation of Industrial Aromatic
1.2 Review the current Safety Data Sheets (SDS) for de-
Hydrocarbons and Related Materials
tailed information concerning toxicity, first aid procedures,
D1722 Test Method for Water Miscibility of Water-Soluble
handling and safety precautions.
Solvents
1.3 The following applies to all specified limits in this
D4052 Test Method for Density, Relative Density, and API
standard; for purposes of determining conformance with this
Gravity of Liquids by Digital Density Meter
standard, an observed value or a calculated value shall be
D5386 Test Method for Color of Liquids Using Tristimulus
rounded off “to the nearest unit” in the last right-hand digit
Colorimetry
used in expressing the specification limit, in accordance with
D8005 Test Method for Color of Clear Liquids (Platinum-
the rounding-off method of Practice E29.
Cobalt Scale)
E29 Practice for Using Significant Digits in Test Data to
1.4 The values stated in SI units are to be regarded as
Determine Conformance with Specifications
standard. No other units of measurement are included in this
E300 Practice for Sampling Industrial Chemicals
standard.
E1064 Test Method for Water in Organic Liquids by Coulo-
1.5 This standard does not purport to address all of the
metric Karl Fischer Titration
safety concerns, if any, associated with its use. It is the
E2409 Test Method for Glycol Impurities in Mono-, Di-, Tri-
responsibility of the user of this standard to establish appro-
and Tetraethylene Glycol and in Mono- and Dipropylene
priate safety, health, and environmental practices and deter-
Glycol (Gas Chromatographic Method)
mine the applicability of regulatory limitations prior to use.
E2679 Test Method for Acidity in Mono-, Di-, Tri- and
1.6 This international standard was developed in accor-
Tetraethylene Glycol by Non-Aqueous Potentiometric
dance with internationally recognized principles on standard-
Titration
ization established in the Decision on Principles for the
E2680 Test Method for Appearance of Clear, Transparent
Development of International Standards, Guides and Recom-
Liquids (Visual Inspection Procedure)
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
3. Requirements
3.1 Industrial grade ethylene glycol shall conform to the
specification chemical and physical requirements (see Table 1).
1
This specification is under the jurisdiction of ASTM Committee D16 on
Aromatic, Industrial, Specialty and Related Chemicals and is the direct responsi-
2
bility of Subcommittee D16.14 on Alcohols & Glycols. For referenced ASTM standards, visit the ASTM website, www.astm.org
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: E1119 − 22 E1119 − 22
Standard Specification for
1
Industrial Grade Ethylene Glycol
This standard is issued under the fixed designation E1119; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorial corrections were made to Table 1 in August 2022.
1. Scope*
1.1 This specification covers industrial grade ethylene glycol.
1.2 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling and
safety precautions.
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an
observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the
specification limit, in accordance with the rounding-off method of Practice E29.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D482 Test Method for Ash from Petroleum Products
D850 Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials
D1722 Test Method for Water Miscibility of Water-Soluble Solvents
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
D8005 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
1
This specification is under the jurisdiction of ASTM Committee D16 on Aromatic, Industrial, Specialty and Related Chemicals and is the direct responsibility of
Subcommittee D16.14 on Alcohols & Glycols.
ɛ1
Current edition approved July 1, 2022. Published July 2022. Originally approved in 1986. Last previous edition approved in 2015 as E1119 – 09 (2015) . DOI:
10.1520/E1119-22.10.1520/E1119-22E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.