iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1482-04

(Guide)

Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring

Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring

SIGNIFICANCE AND USE
This practice provides minimum recommendations for the installation and preparation of wood-based, fiber-reinforced gypsum and fiber-cement panel underlayments suitable to receive resilient floor coverings. Actual requirements for materials to be used, mixtures, and other details are generally included as part of project plans or specification detail and may vary from the minimum recommendations set forth in this practice.
SCOPE
1.1 This practice includes recommendations for wood based, fiber reinforced gypsum and fiber-cement panel underlayment/subfloor assemblies upon which resilient flooring may be installed.
1.2 This practice does not cover the adequacy of the subfloor assembly to perform its structural requirements, which is governed by local building codes.
1.3 This practice does not supersede in any manner the resilient flooring, underlayment or adhesive manufacturer's written instructions. Consult the individual resilient flooring, underlayment or adhesive manufacturer for specific recommendations.
1.4 See Supplementary Requirements for "Select Warnings" that have been provided.
1.5 The values stated in inch/pound units are to be regarded as standard; the metric units in parentheses are for reference only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
29-Feb-2004
ICS
97.150 - Floor coverings
Technical Committee
F06 - Resilient Floor Coverings
Drafting Committee
F06.40 - Practices
Current Stage
Ref Project

Relations

Replaces
ASTM F1482-03 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
Effective Date
01-Mar-2004
Replaced By
ASTM F1482-04(2009)e1 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
Effective Date
01-May-2009
Referred By
ASTM F2753-21 - Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System
Effective Date
01-Mar-2004
Referred By
ASTM F1344-21a - Standard Specification for Rubber Floor Tile
Effective Date
01-Mar-2004
Referred By
ASTM F1303-04(2021) - Standard Specification for Sheet Vinyl Floor Covering with Backing
Effective Date
01-Mar-2004
Referred By
ASTM F3041-14(2019) - Standard Specification for Bonded Rubber Crumb Floor Coverings
Effective Date
01-Mar-2004
Referred By
ASTM F2471-19 - Standard Practice for Installation of Thick Poured Lightweight Cellular Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
Effective Date
01-Mar-2004
Referred By
ASTM F2034-18 - Standard Specification for Sheet Linoleum Floor Covering
Effective Date
01-Mar-2004
Referred By
ASTM F1859-21a - Standard Specification for Rubber Sheet Floor Covering Without Backing
Effective Date
01-Mar-2004
Referred By
ASTM F1860-21a - Standard Specification for Rubber Sheet Floor Covering With Backing
Effective Date
01-Mar-2004
Referred By
ASTM F2873-20 - Standard Practice for the Installation of Self-Leveling Underlayment and the Preparation of Surface to Receive Resilient Flooring
Effective Date
01-Mar-2004
Referred By
ASTM F2419-11(2021) - Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
Effective Date
01-Mar-2004
Referred By
ASTM F2678-16(2021) - Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Thick Poured Lightweight Cellular Concrete Underlayments, and Concrete Subfloors with Underlayment Patching Compounds to Receive Resilient Flooring
Effective Date
01-Mar-2004
Referred By
ASTM F3311-19 - Standard Practice for Mat Bond Evaluation of Performance and Compatibility for Resilient Flooring System Components Prior to Installation
Effective Date
01-Mar-2004

Buy Standard

ASTM F1482-04 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient FlooringASTM F1482-04 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
PreviousNext
Guide
ASTM F1482-04 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1482–04
Standard Practice for
Installation and Preparation of Panel Type Underlayments to
1
Receive Resilient Flooring
This standard is issued under the fixed designation F 1482; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
3
1. Scope ANSI/A208.1-1998 Particleboard
3
ANSI/AHAA135.4-1995 Basic Hardboard
1.1 This practice includes recommendations for the instal-
2.3 NIST Standards:
lation of panel type underlayments including wood based, fiber
Voluntary Product Standard PS1-95 for Construction and
reinforced gypsum and fiber-cement panel underlayment/
3,4
Industrial Plywood
subfloor assemblies upon which resilient flooring may be
Voluntary Product Standard PS2-92 for Wood-Based
installed.
3,4
Structural-Use Panels
1.2 The structural integrity of subfloor assemblies is gov-
2.4 Other Documents:
erned by local building codes.
5
APA Engineered Wood Construction Guide, Form E30
1.3 This practice does not supersede in any manner the
APAInstallation and Preparation of Plywood Underlayment
resilient flooring, underlayment or adhesive manufacturer’s
5
for Resilient Flooring, Form L335
written instructions. Consult the individual resilient flooring,
Resilient Floor Covering Institute (RFCI) Recommended
underlayment or adhesive manufacturer for specific recom-
Work Practices for Removal of Resilient Floor Coverings
mendations. Manufacturer’s instructions supercede the recom-
6
(January 1998)
mendations included in this practice.
Lead-Based Paint: Interim Guidelines for Hazard Identifi-
1.4 SeeSupplementaryRequirementsfor“SelectWarnings”
cation andAbatement in Public and Indian housing (1991
that have been provided.
7
revised)
1.5 The values stated in inch/pound units are to be regarded
as standard. The metric units in parentheses are for reference
3. Terminology
only.
3.1 Definitions used in this standard shall be in accordance
1.6 This standard does not purport to address all of the
with Terminology F 141.
safety concerns, if any, associated with its use. It is the
3.2 Definitions of Terms Specific to This Standard:
responsibility of the user of this standard to establish appro-
3.2.1 fully adhered flooring—resilient flooring which has
priate safety and health practices and determine the applica-
adhesive under the entire product, bonding it to the underlay-
bility of regulatory limitations prior to use.
ment surface.
2. Referenced Documents 3.2.2 non fully adhered flooring—resilient flooring that may
2
be loose laid, in which no adhesive is utilized, or partially
2.1 ASTM Standards:
bonded to the surface of the underlayment, typically at seams
C 1278/C 1278M Specification for Fiber-Reinforced Gyp-
or the surrounding perimeter, or both, of the product.
sum Panel
C 1288 Specification for Discrete Non-Asbestos Fiber-
4. Significance and Use
Cement Interior Substrate Sheets
4.1 This practice provides minimum recommendations for
F 141 Terminology Relating to Resilient Floor Coverings
theinstallationandpreparationofwood-based,fiber-reinforced
2.2 ANSI Standards:
3
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
1
ThisguideisunderthejurisdictionofASTMCommitteeF06onResilientFloor 4th Floor, New York, NY 10036, www.ansi.org.
4
Coverings and is the direct responsibility of Subcommittee F06.40 on Special Available from National Institute of Standards and Technology (NIST), 100
Properties. Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460, www.nist.gov.
5
Current edition approved March 1, 2004. Published April 2004. Originally Available from APA—The Engineered Wood Association, 7011 S. 19th St.,
approved in 1994. Last previous edition approved in 2003 as F 1482 – 03. Tacoma, WA 98466–5399, www.apawood.org.
2 6
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Resilient Floor Covering Institute, 401 E. Jefferson Suite 102 Rockville, MD
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 20850, www.rfci.com.
7
Standards volume information, refer to the standard’s Document Summary page on U.S. Department of Housing & Urban Development, Washington, DC,
the ASTM website. www.hud.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1482–04
gypsum and fiber-cement panel underlayments suitable to literature offers specific recommendations or prohibitions as to
receive resilient floor coverings. Actual requirements for ma- types of underlayments for use under their flooring products.
terials to be used, mixtures, and other details are g
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3441-23a(Guide)
Standard Guide for Measurement of pH Below Resilient Flooring Installations

SIGNIFICANCE AND USE
4.1 There is typically a higher concentration of soluble alkali salts in the surface region of a concrete slab due to the initial bleeding process of a freshly placed concrete slab. If after a resilient floor covering material is installed there is sufficient moisture within the slab to place these salts into solution a potentially damaging high pH solution can develop beneath the installed material.  
4.2 Results obtained through the use of this guide indicate the comparative pH of reagent water placed on properly prepared concrete slab surfaces only at the time of the procedure and in the specific locations evaluated.  
4.3 If pre-installation surface pH evaluation is required by the manufacturer of the resilient flooring, adhesive, patching/underlayment products or project specifications, their instructions and limitations should be consulted.
SCOPE
1.1 This guide discusses procedures that may be used for evaluating the comparative change in pH of reagent water placed on the surface of a properly prepared concrete slab surface.  
1.2 This guide is intended to be used in conjunction with the flat surface electrode pH meter manufacturer’s calibration procedures, operation instructions, and interpretive data where available.  
1.3 This guide is intended to be used in conjunction with the pH paper manufacturer’s instructions, product shelf life, and interpretive data where available.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use Some specific hazards statements are given in Section 9 on Hazards.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3404-23a(Specification)
Standard Specification for Heterogeneous Polyurethane Tile or Plank Flooring

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F141-23(Terminology)
Standard Terminology Relating to Resilient Floor Coverings
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1516-23(Practice)
Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)

SIGNIFICANCE AND USE
4.1 Seams in some resilient flooring are heat sealed to prevent openings from forming between cut edges and to prevent penetrations of dirt, liquids, etc., into the seams. Decorative appearances may also be achieved using contrasting heat weld thread (rod).
SCOPE
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in resilient flooring sealed by the heat weld method.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See precaution information in 6.1.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F693-01(2023)(Practice)
Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers

SIGNIFICANCE AND USE
4.1 Seams in some sheet resilient flooring are sealed to prevent openings from forming between cut edges and prevent penetrations of dirt, liquids, etc., into the seams.
SCOPE
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in sheet resilient flooring sealed with liquid seam sealers.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3191-23(Practice)
Standard Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring

SIGNIFICANCE AND USE
5.1 The ability of a substrate surface to readily absorb water is a key indicator in determining how to correctly install many types of flooring adhesives, primers, self-leveling underlayments, and other products. Several flooring industry publications such as CRI’s Carpet Installation Standard, RFCI’s Recommended Installation Practice for Homogenous Sheet Flooring, Fully-Adhered, as well as most flooring, adhesive, primer, and underlayment manufacturers reference substrate surface porosity criteria in their application instructions since this directly impacts the spread rate of directly applied material, the open time, and other critical installation factors.  
5.2 Installing flooring products over low or non-absorptive (sometimes referred to as “non-porous”) substrates such as densely machine-troweled concrete, mature and well-hydrated concrete, existing resilient flooring, polymer terrazzo and others may require adjustments to the surface preparation method or product selection to ensure a successful installation.  
5.3 Use this practice to obtain a qualitative assessment of substrate water absorption (porosity) and whether or not that substrate should be regarded as porous/absorptive or non-porous/non-absorptive as these terms relate to the installation of resilient floor coverings, adhesives, self-leveling underlayments, primers, and other products. This practice will produce results directly applicable to determining appropriate surface preparation requirements in accordance with manufacturer’s specifications, but it is in no way meant to replace published manufacturer’s literature regarding the determination of substrate water absorption (porosity) and the impact such has, if any, on substrate preparation requirements and on the installation of their respective materials.  
5.4 Substrates that evidence immediate absorption, are chalky or dusty, or have varying degrees of absorption may require priming or other additional surface preparation prior to subseq...
SCOPE
1.1 This practice covers the determination of whether or not a substrate surface, in lieu of written instruction from a product manufacturer, is considered porous or non-porous prior to the installation of resilient flooring materials.  
1.2 Although carpet tiles, carpet, wood flooring, coatings, films, paints, self-leveling and trowel-grade underlayments, primers, and other associated products are not specifically intended to be included in the category of resilient floor coverings, the procedures included in this practice may be useful for assessing the substrate water absorption for substrates to receive such materials.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 6 on Hazards.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3403-23(Specification)
Standard Specification for Heterogeneous Polyurethane Sheet Flooring

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane sheet flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane sheet flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F710-22(Practice)
Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring

ABSTRACT
This practice covers the procedure for determining the acceptability of concrete floors for the installation of resilient flooring. It also includes suggestions for ensuring that the constructed concrete floor is acceptable for such installations but does not cover tests for adequacy of the concrete floor to perform structural requirements. A permanent, effective moisture vapor retarder, of the specified thickness and permeance, is required under all on- or below-grade concrete floors. Concrete floors for resilient floorings should be permanently dry, clean, smooth, structurally sound, and free of substances that may prevent adhesive bonding. Surface cracks, grooves, depression, control joints or other non-moving joints, and other irregularities should be filled or smoothed with latex patching or a recommended underlayment compound. The surface of the floor should be cleaned by scraping, brushing, vacuuming, or any other method. All concrete slabs should be tested for moisture regardless of age or grade level while all concrete floors should be tested for pH before installing resilient flooring.
SCOPE
1.1 This practice covers the determination of the acceptability of a concrete floor for the installation of resilient flooring.  
1.2 This practice includes suggestions for the construction of a concrete floor to ensure its acceptability for installation of resilient flooring.  
1.3 This practice does not cover the adequacy of the concrete floor to perform its structural requirements.  
1.4 This practice covers the necessary preparation of concrete floors prior to the installation of resilient flooring.  
1.5 This practice does not supersede in any manner the resilient flooring or adhesive manufacturer's written instructions. Consult the individual manufacturer for specific recommendations.  
1.6 Although carpet tiles, carpet, wood flooring, coatings, films, and paints are not specifically intended to be included in the category of resilient floor coverings, the procedures included in this practice may be useful for preparing concrete floors to receive such finishes.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See 4.1.1, 7.1.1, and 7.1.2 for specific warning statements.  
1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM F1037-18(2022)(Test Method)
Standard Test Method for Visual Rating of Appearance of Resilient Floors

SIGNIFICANCE AND USE
4.1 Ratings are developed by some subjective or comparative evaluation criteria, or both, of a sample(s) to some reference criteria or when compared to a control sample. These parameters generally include change in gloss, color, surface texture, alterations to pattern and possibly restorability of appearance with normal maintenance procedures, including the use of finishes or buffing. Rating is done by a qualified individual or preferably by a panel of qualified observers under specified lighting conditions in accordance with prescribed procedures.
SCOPE
1.1 This test method is intended to provide a numerical rating system for classification of resilient floors during the various stages of their wear life in relation to their condition, as perceived by a knowledgeable user.  
1.2 This test method is intended to allow comparison between two or more samples or groups of samples for differences in visual appearance.  
1.3 This method provides recommended viewing conditions and lighting for rating visual differences between samples or groups of samples.  
1.4 This method can be utilized to evaluate change in visual appearance before and after some specified test condition exposure, for example, in service wear due to foot traffic, or other tests where change in appearance might occur.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental health practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F410-08(2022)(Test Method)
Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement

SIGNIFICANCE AND USE
3.1 This test method is applicable for wear layers with a minimum thickness of 0.001 in. (0.02 mm) to a maximum thickness of 0.1 in. (2.54 mm), where measurements within 0.0005 in. or 0.01 mm are tolerable.
SCOPE
1.1 This test method covers the determination of the thickness of the wear layer of resilient non-textile floor coverings, in tile or sheet form, with or without felt backing or foam layer, by optical measurement.  
1.2 This test method is applicable for wear layers with a minimum thickness of 0.0004 in. (0.01 mm) to a maximum thickness of 0.1 in. (2.54 mm), where measurements within 0.0001 in. or 0.0025 mm are tolerable.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off