iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2052-05(2010)

(Test Method)

Standard Test Method for Colorfastness of Zippers to Drycleaning

Standard Test Method for Colorfastness of Zippers to Drycleaning

SIGNIFICANCE AND USE
Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1—For guidance in evaluating the results of this test method, refer to Practice D3692.
This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.
If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no p...
SCOPE
1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this test method.
1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-May-2010
ICS
61.040 - Headgear. Clothing accessories. Fastening of clothing
Technical Committee
D13 - Textiles
Drafting Committee
D13.54 - Subassemblies
Current Stage
Ref Project

Relations

Replaces
ASTM D2052-05 - Standard Test Method for Colorfastness of Zippers to Drycleaning
Effective Date
01-Jun-2010
Referred By
ASTM D2062-03(2021) - Standard Test Methods for Operability of Zippers
Effective Date
01-Jun-2010
Referred By
ASTM D2058-03(2022) - Standard Test Method for Durability of Finish of Zippers to Drycleaning
Effective Date
01-Jun-2010
Referred By
ASTM D3692-89(2021) - Standard Practice for Selection of Zippers for Care-Labeled Apparel and Household Furnishings
Effective Date
01-Jun-2010
Referred By
ASTM D2057-05(2022) - Standard Test Method for Colorfastness of Zippers to Laundering
Effective Date
01-Jun-2010
Referred By
ASTM D3181-15(2019) - Standard Guide for Conducting Wear Tests on Textiles
Effective Date
01-Jun-2010
Referred By
ASTM D2051-14(2022) - Standard Test Method for Durability of Finish of Zippers to Laundering
Effective Date
01-Jun-2010
Referred By
ASTM D2053-99(2022) - Standard Test Method for Colorfastness of Zippers to Light
Effective Date
01-Jun-2010
Referred By
ASTM D2060-14(2022) - Standard Test Methods for Measuring Zipper Dimensions
Effective Date
01-Jun-2010
Referred By
ASTM D2061-07(2021) - Standard Test Methods for Strength Tests for Zippers
Effective Date
01-Jun-2010
Referred By
ASTM D2059/D2059M-03(2022) - Standard Test Method for Resistance of Zippers to Salt Spray (Fog)
Effective Date
01-Jun-2010

Buy Standard

ASTM D2052-05(2010) - Standard Test Method for Colorfastness of Zippers to DrycleaningASTM D2052-05(2010) - Standard Test Method for Colorfastness of Zippers to Drycleaning
PreviousNext
Standard
ASTM D2052-05(2010) - Standard Test Method for Colorfastness of Zippers to Drycleaning
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2052 − 05(Reapproved 2010)
Standard Test Method for
Colorfastness of Zippers to Drycleaning
This standard is issued under the fixed designation D2052; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2060 Test Methods for Measuring Zipper Dimensions
D2061 Test Methods for Strength Tests for Zippers
1.1 This test method covers the determination of change in
D2062 Test Methods for Operability of Zippers
shade and of staining of zipper stringers under drycleaning
D2724 Test Methods for Bonded, Fused, and Laminated
conditions. This test method is applicable to the textile portion
Apparel Fabrics
of zipper stringers of all materials.
D3692 Practice for Selection of Zippers for Care-Labeled
1.2 The values stated in either SI units or inch-pound units
Apparel and Household Furnishings
are to be regarded separately as the standard. Within the text,
2.2 AATCC Methods:
the inch-pound units are shown in parentheses. The values
Evaluation Procedure 1, AATCC Gray Scale for Color
stated in each system are not exact equivalents; therefore, each
Change
system shall be used independently of the other. Combining
Evaluation Procedure 3, AATCC Chromatic Transference
values from the two systems may result in nonconformance
Scale
with this test method.
3. Terminology
1.3 This standard does not purport to address all of the
safety problems associated with its use. It is the responsibility
3.1 For all terminology related to D13.54, Subassemblies,
of whoever uses this standard to consult and establish appro-
refer to Terminology D2050.
priate safety and health practices and determine the applica-
3.1.1 The following terms are relevant to this standard:
bility of regulatory limitations prior to use.
colorfastness, drycleaning.
3.2 For all other terminology relating to textiles, see Termi-
2. Referenced Documents
nology D123.
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
4. Summary of Test Method
D2050 Terminology Relating to Fasteners and Closures
4.1 A specimen of the zipper stringer, in conjunction with
Used with Textiles
multifiber test fabric is subjected to drycleaning. The dry-
D2051 Test Method for Durability of Finish of Zippers to
cleaned specimen is compared with an original specimen (see
Laundering
10.1)andanychangeincolorofthespecimenorstainingofthe
D2053 Test Method for Colorfastness of Zippers to Light
multifiber test cloth is then assessed using the AATCC Gray
D2054 Test Method for Colorfastness of Zipper Tapes to
ScaleforColorChangeortheAATCCChromaticTransference
Crocking
Scale, as appropriate.
D2057 Test Method for Colorfastness of Zippers to Laun-
dering
5. Significance and Use
D2058 Test Method for Durability of Finish of Zippers to
5.1 Test Method D2052 is useful for testing to determine if
Drycleaning
the degree of alteration in shade is satisfactory for the intended
D2059 Test Method for Resistance of Zippers to Salt Spray
end-use and for determining if unacceptable staining of color
(Fog)
into adjacent fabric will occur.
NOTE1—Forguidanceinevaluatingtheresultsofthistestmethod,refer
This test method is under the jurisdiction ofASTM Committee D13 on Textiles
to Practice D3692.
and is the direct responsibility of Subcommittee D13.54 on Subassemblies. The
method was developed in cooperation with the Slide Fastener Assn., Inc.
5.2 This test method is considered satisfactory for accep-
Current edition approved June 1, 2010. Published August 2010. Originally
tance testing of commercial shipments because the method has
approved in 1961. Last previous edition approved in 2005 as D2052 – 05. DOI:
been used extensively in the trade for acceptance testing.
10.1520/D2052-05R10.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Technical Manual of the American Association of Textile Chemists and
the ASTM website. Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D2052 − 05 (2010)
5.2.1 If there are differences of practical significance be- specified in Section8 at random from each container in the lot
tween reported test results for two laboratories (or more), sample. Consider the zippers as both the laboratory sample and
comparative tests should be performed to determine if their is the test specimens.
a statistical bias between them, using competent statistical
8. Number of Specimens
assistance.As a minimum, the test samples should be used that
8.1 Unless otherwise agreed upon, as when specified in an
are as homogeneous as possible, that are drawn from the
applicable material specification, take one zipper at random
material from which the disparate test results were obtained,
from each individual container selected for sampling.
and that are randomly assigned in equal numbers to each
laboratory for testing. Other materials with established test
9. Test Specimen
values may be used for this purpose. The test results from the
9.1 The test specimen shall consist of approximately 40 cm
two laboratories should be compared using a statistical test for
(6.4 in. ) of zipper stringer taken from each zipper sample.The
unpaired data, at probability level chosen prior to the testing
specimen need not be a continuous length.
series. If a bias is found, either its cause must be found and
corrected, or future test results must be adjusted in consider-
9.2 A duplicate specimen shall be prepared and held for
ation of the known bias.
comparison in evaluating the results of the test.
5.3 The method(s) in this standard along with those in Test
10. Conditioning
Methods D2051, D2053, D2054, D2057, D2058, D2059,
10.1 The specimens shall be conditioned for at least4hin
D2060, D2061, and D2062 are a collection of proven zipper
the standard atmosph
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2050-23(Terminology)
Standard Terminology Relating to Fastener Subassemblies Used in the Manufacture of Textiles

SCOPE
1.1 This standard identifies terminology related to subassemblies which are categorized as any component that is used in the construction or assembly of a textile product. Subassemblies can be in the form of components used as closures (for example, slide fasteners, buttons, snap fasteners, hook and loop (touch) fasteners) or methods used to join textile sections (for example, stitches and seams).  
1.2 Terms relating to Buttons are found in Section 3.  
1.3 Terms relating to Hook and Loop (Touch) fasteners are in Section 4.  
1.4 Terms relating to Snap Fasteners are found in Section 5.  
1.5 Terms relating to Slide Fasteners are found in Section 6.  
1.6 For other terms related to textiles, refer to Terminology D123.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4035-22(Specification)
Standard Performance Specification for Knitted Necktie and Scarf Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4035 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers knitted necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4153-22(Specification)
Standard Performance Specification for Men's, Women's, and Children's Woven Handkerchief Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4153 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics to be used in the manufacture of men's, women's, and children's handkerchiefs, both utilitarian and decorative.  
1.2 This performance specification is not applicable to open-work fabrics such as lace which is used primarily to decorate handkerchiefs, or woven fabrics used for the manufacture of scarves.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2060-14(2022)(Test Method)
Standard Test Methods for Measuring Zipper Dimensions

SIGNIFICANCE AND USE
4.1 The significance of specific tests is discussed in the appropriate sections.  
4.2 These test methods are considered satisfactory for acceptance testing of commercial shipments because the test methods have been used extensively in the trade for this purpose, and because current estimates of between-laboratory precision are acceptable in most cases.  
4.2.1 In case of a dispute arising from differences in reported test results when using Test Methods D2060 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias if found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.  
4.3 The test method(s) in these test methods, along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2059, D2061, and D2062, are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either be...
SCOPE
1.1 These test methods cover the measurement of the dimensions of all types and sizes of zippers.  
1.2 The test methods appear as follows:    
Sections  
Chain Flatness  
34 – 39  
Chain Straightness  
40 – 44  
Chain Thickness  
28 – 33  
Chain Width  
45 – 50  
Length of Zipper or Parts  
9 – 14  
Longitudinal Dimensional Change  
51 – 58  
Slider Mouth Width  
21 – 27  
Tape Width  
15 – 20  
1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D2057-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Laundering

SIGNIFICANCE AND USE
5.1 Test Method D2057 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in D2051, D2052, D2053, D2054, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because...
SCOPE
1.1 This test method covers the determination of alteration in shade and of staining under conditions similar to that experienced in domestic washing of zipper stringers. This test method is applicable to the textile portion of zipper stringers that utilize tapes made of cotton, linen, or manufactured organic fibers, and to combinations thereof.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2053-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Light

SIGNIFICANCE AND USE
5.1 This test method is useful in determining if the loss of color due to light exposure is satisfactory for the intended end-use.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The test method(s) in this standard along with those in Test Methods D2051, D2052, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and...
SCOPE
1.1 This test method covers the determination of the alteration in shade of the textile portion of zippers when exposed to light, regardless of the materials of manufacture.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2059/D2059M-03(2022)(Test Method)
Standard Test Method for Resistance of Zippers to Salt Spray (Fog)

SIGNIFICANCE AND USE
5.1 The resistance of a zipper to a variety of saline and non-saline environments can be estimated from the amount and nature of corrosion products and their effect on operability. Results of exposure to the salt spray are merely indicative of the reaction to other corrosive conditions. While the results cannot be related precisely to a given length of exposure in a specific atmosphere, they are useful for measuring relative performance under prescribed conditions for controlling a manufacturing process, and for measuring the effectiveness of protective coatings.  
5.2 Test Method D2059 for the determination of the resistance of zippers to salt spray is considered satisfactory for acceptance testing of commercial shipments of zippers because the test method is used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. T...
SCOPE
1.1 This test method covers the determination of the resistance of all types of zippers to corrosion and their ability to function properly after exposure of specified duration in a prescribed salt spray.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2054-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zipper Tapes to Crocking

SIGNIFICANCE AND USE
5.1 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the determination of the degree of color that may be transferred from the textile tape of zippers of all fibers to other surfaces by rubbing under wet or dry conditions, or both.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2052-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this test method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been publishe...
SCOPE
1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2058-03(2022)(Test Method)
Standard Test Method for Durability of Finish of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2058 is useful for determining the effect of repeated drycleaning on the appearance of the decorative coating of a zipper.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thoroug...
SCOPE
1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off