ASTM D6158-16
(Specification)Standard Specification for Mineral Hydraulic Oils
Standard Specification for Mineral Hydraulic Oils
ABSTRACT
This specification covers the standard for mineral oils used in hydraulic systems which require refined base oil (Class HH), refined mineral base oil with rust and oxidation inhibitors (Class HL) or refined mineral base oil with rust and oxidation inhibitors plus antiwear characteristics (Class HM). This specification only covers lubricating oils before they are installed in the hydraulic system and does not include all hydraulic oils. Requirements for the mineral oils shall include, but not limited to, viscosity, specific gravity, appearance, flash point, chemical acid number, corrosion, water separation, elastomer compatibility, air release, and thermal stability.
SCOPE
1.1 This specification covers mineral and synthetic oils of the types API groups I, II, III, and IV used in hydraulic systems, where the performance requirements demand fluids with one of the following characteristics:
1.1.1 A refined base oil or synthetic base stock (Class HH),
1.1.2 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors (Class HL),
1.1.3 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics (Class HM),
1.1.4 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors, anti-wear characteristics, and increased viscosity index higher than 140 (Class HV),
1.1.5 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics meeting a higher performance level than an HM fluid to address higher demanding hydraulic systems (Class HMHP), and
1.1.6 A refined mineral base oil with rust or synthetic base stock and oxidation inhibitors, anti-wear characteristics, and increased viscosity index higher than 140 meeting a higher performance level than an HV fluid to address higher demanding hydraulic systems (Class HVHP).
1.2 This specification defines the requirements of mineral oil-based or synthetic-based hydraulic fluids that are compatible with most existing machinery components when there is adequate maintenance.
1.3 This specification defines only new lubricating oils before they are installed in the hydraulic system.
1.4 This specification defines specific types of hydraulic oils. It does not include all hydraulic oils. Some oils that are not included may be satisfactory for certain hydraulic applications. Certain equipment or conditions of use may permit or require a wider or narrower range of characteristics than those described herein.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5.1 Exception—In X1.3.9 on Wear Protection, the values of pump pressure are in MPa, and the psi follows in brackets as a reference point immediately recognized by a large part of the industry.
1.6 The following safety hazard caveat pertains to the test methods referenced in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitation prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6158 −16
Standard Specification for
1
Mineral Hydraulic Oils
This standard is issued under the fixed designation D6158; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.5 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
1.1 This specification covers mineral and synthetic oils of
standard.
the types API groups I, II, III, and IV used in hydraulic
1.5.1 Exception—In X1.3.9 on Wear Protection, the values
systems, where the performance requirements demand fluids
ofpumppressureareinMPa,andthepsifollowsinbracketsas
with one of the following characteristics:
a reference point immediately recognized by a large part of the
1.1.1 Arefined base oil or synthetic base stock (Class HH),
industry.
1.1.2 Arefined mineral base oil or synthetic base stock with
1.6 The following safety hazard caveat pertains to the test
rust and oxidation inhibitors (Class HL),
methods referenced in this specification. This standard does
1.1.3 Arefined mineral base oil or synthetic base stock with
not purport to address all of the safety concerns, if any,
rust and oxidation inhibitors plus anti-wear characteristics
associated with its use. It is the responsibility of the user of this
(Class HM),
standard to establish appropriate safety and health practices
1.1.4 Arefined mineral base oil or synthetic base stock with
and determine the applicability of regulatory limitation prior
rust and oxidation inhibitors, anti-wear characteristics, and
to use.
increased viscosity index higher than 140 (Class HV),
1.1.5 Arefined mineral base oil or synthetic base stock with
2. Referenced Documents
rust and oxidation inhibitors plus anti-wear characteristics
2
meeting a higher performance level than an HM fluid to 2.1 ASTM Standards:
address higher demanding hydraulic systems (Class HMHP),
D92 Test Method for Flash and Fire Points by Cleveland
and Open Cup Tester
1.1.6 A refined mineral base oil with rust or synthetic base D97 Test Method for Pour Point of Petroleum Products
stock and oxidation inhibitors, anti-wear characteristics, and D130 Test Method for Corrosiveness to Copper from Petro-
increased viscosity index higher than 140 meeting a higher leum Products by Copper Strip Test
performance level than an HV fluid to address higher demand-
D445 Test Method for Kinematic Viscosity of Transparent
ing hydraulic systems (Class HVHP). and Opaque Liquids (and Calculation of Dynamic Viscos-
ity)
1.2 This specification defines the requirements of mineral
D471 Test Method for Rubber Property—Effect of Liquids
oil-based or synthetic-based hydraulic fluids that are compat-
D664 Test Method for Acid Number of Petroleum Products
ible with most existing machinery components when there is
by Potentiometric Titration
adequate maintenance.
D665 Test Method for Rust-Preventing Characteristics of
1.3 This specification defines only new lubricating oils
Inhibited Mineral Oil in the Presence of Water
before they are installed in the hydraulic system.
D892 Test Method for Foaming Characteristics of Lubricat-
1.4 This specification defines specific types of hydraulic ing Oils
oils.Itdoesnotincludeallhydraulicoils.Someoilsthatarenot D943 Test Method for Oxidation Characteristics of Inhibited
included may be satisfactory for certain hydraulic applications. Mineral Oils
Certain equipment or conditions of use may permit or require D974 Test Method for Acid and Base Number by Color-
a wider or narrower range of characteristics than those de- Indicator Titration
scribed herein. D1298 Test Method for Density, Relative Density, or API
Gravity of Crude Petroleum and Liquid Petroleum Prod-
ucts by Hydrometer Method
1
This specification is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
2
Subcommittee D02.N0 on Hydraulic Fluids. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 15, 2016. Published February 2016. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1997. Last previous edition approved in 2014 as D6158 – 14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D6158-16. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6158−16
D1401 TestMethodforWaterSeparabilityofPetroleum
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6158 − 14 D6158 − 16
Standard Specification for
1
Mineral Hydraulic Oils
This standard is issued under the fixed designation D6158; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers mineral oils and synthetic oils of the types API groups I, II, III, and IV used in hydraulic systems,
where the performance requirements demand fluids with one of the following characteristics:
1.1.1 A refined base oil or synthetic base stock (Class HH),
1.1.2 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors (Class HL), and
1.1.3 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics (Class
HM),
1.1.4 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus antiwear characteristics (Class
HM).inhibitors, anti-wear characteristics, and increased viscosity index higher than 140 (Class HV),
1.1.5 A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics meeting
a higher performance level than an HM fluid to address higher demanding hydraulic systems (Class HMHP), and
1.1.6 A refined mineral base oil with rust or synthetic base stock and oxidation inhibitors, anti-wear characteristics, and
increased viscosity index higher than 140 meeting a higher performance level than an HV fluid to address higher demanding
hydraulic systems (Class HVHP).
1.2 This specification defines the requirements of mineral oil-based or synthetic-based hydraulic fluids that are compatible with
most existing machinery components when there is adequate maintenance.
1.3 This specification defines only new lubricating oils before they are installed in the hydraulic system.
1.4 This specification defines specific types of hydraulic oils. It does not include all hydraulic oils. Some oils that are not
included may be satisfactory for certain hydraulic applications. Certain equipment or conditions of use may permit or require a
wider or narrower range of characteristics than those described herein.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5.1 Exception—In X1.3.9 on Wear Protection, the values of pump pressure are in MPa, and the psi follows in brackets as a
reference point immediately recognized by a large part of the industry.
1.6 The following safety hazard caveat pertains to the test methods referenced in this specification.This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitation prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
D97 Test Method for Pour Point of Petroleum Products
D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D471 Test Method for Rubber Property—Effect of Liquids
D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration
D665 Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
D892 Test Method for Foaming Characteristics of Lubricating Oils
1
This specification is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.N0.10D02.N0 on SpecificationsHydraulic Fluids.
Current edition approved Dec. 1, 2014Jan. 15, 2016. Published February 2015February 2016. Originally approved in 1997. Last previous edition approved in 20102014
as D6158 – 10.D6158 – 14. DOI: 10.1520/D6158-14.10.1520/D6158-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C70
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.