ASTM A905-04(2010)

Standard Specification for Steel Wire, Pressure Vessel Winding

ABSTRACT
This specification covers high strength, cold drawn or cold rolled steel wire with rectangular cross-section and round mill edge. The wire is intended for use in pre-stressed vessel and press frame windings. The steel shall be manufactured by basic oxygen, electric furnace, or vacuum induction processes and produced as ingot cast or continuous cast. Materials shall be tested for contents of carbon, manganese, phosphorus, sulphur, and silicon. A tension tests shall also be performed to evaluate mechanical properties conformance. Guidelines for workmanship, finish, and appearance are stated, as well as the inspection, certification of reports, packaging, marking, and loading for shipment.
SCOPE
1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.

General Information

• Status: Historical
• Publication Date: 31-Mar-2010
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.03 - Steel Rod and Wire

Relations

• Replaces: ASTM A905-04 - Standard Specification for Steel Wire, Pressure Vessel Winding
• Effective Date: 01-Apr-2010
• Replaced By: ASTM A905-04(2017) - Standard Specification for Steel Wire, Pressure Vessel Winding
• Effective Date: 01-Sep-2017

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A905 −04 (Reapproved 2010)
Standard Specification for
1
Steel Wire, Pressure Vessel Winding
This standard is issued under the fixed designation A905; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 Military Standard:
MIL-STD-163 Steel Mill Products, Preparation for Ship-
1.1 This specification covers requirements for a high
4
ment and Storage
strength drawn and cold rolled steel wire in two strength
2.3 Federal Standard:
classes, with rectangular cross section, and round mill edge.
6
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
This wire is intended for prestressed vessel and press frame
2.4 AIAG Standard:
windings.
AIAGB-5 02.00 Primary Metals Identification Tag Applica-
1.2 The values stated in either inch-pound units or SI
5
tion Standard
(metric) units are to be regarded separately as standards.
Within the text and tables, the SI units are shown in parenthe-
3. Ordering Information
ses.The values stated in each system are not exact equivalents.
3.1 It shall be the responsibility of the purchaser to specify
Therefore, each system must be used independent of the other.
all requirements that are necessary for material under this
Combining values from the two systems may result in noncon-
specification. Such requirements may include, but are not
formance with the specification.
limited to, the following:
3.1.1 Quantity (mass),
2. Referenced Documents
3.1.2 Name of material,
2
2.1 ASTM Standards:
3.1.3 Dimensions (see Section 7),
A370 Test Methods and Definitions for Mechanical Testing
3.1.4 Finish (see Section 8),
of Steel Products
3.1.5 Packaging (see Section 11),
A510 Specification for General Requirements for Wire Rods
3.1.6 Cast or heat analysis report (see Section 5),
and Coarse Round Wire, Carbon Steel
3.1.7 Number of certification or test reports required (see
A510M Specification for General Requirements for Wire
Section 10),
Rods and Coarse Round Wire, Carbon Steel (Metric)
3.1.8 ASTM designation and year of issue, and
3
(Withdrawn 2011)
3.1.9 Supplementary requirements, if any.
A700 Practices for Packaging, Marking, and Loading Meth-
ods for Steel Products for Shipment
4. Material and Manufacture
E30 Test Methods for ChemicalAnalysis of Steel, Cast Iron,
3 4.1 The steel shall be produced by any of the following
Open-Hearth Iron, and Wrought Iron (Withdrawn 1995)
primary processes: (1) basic oxygen, and (2) electric furnace or
E309 Practice for Eddy-Current Examination of Steel Tubu-
vacuum induction (VIM). The primary melting may incorpo-
lar Products Using Magnetic Saturation
rate separate degassing or refining and may be followed by
secondary melting by the electrode slag process (ESR) or the
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
vacuum arc remelting process (VAR).
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
4.1.1 The steel may be ingot cast or continuously cast.
A01.03 on Steel Rod and Wire.
Current edition approved April 1, 2010. Published April 2010. Originally
4.2 The finished wire shall be free from detrimental pipe
approved in 1991. Last previous edition approved in 2004 as A905 – 04. DOI:
and undue segregation.
10.1520/A0905-04R10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
the ASTM website. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
3 5
The last approved version of this historical standard is referenced on Available fromAutomotive IndustryAction Group (AIAG), 26200 Lahser Rd.,
www.astm.org. Suite 200, Southfield, MI 48034.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A905−04 (2010)
TABLE 2 Tensile Requirements
4.3 The wire shall be cold drawn or cold rolled, or both, to
A
produce the desired mechanical properties and dimensions Thickness Tensile strength Yield strength Elongation
in. (mm)
min. ksi min. ksi min %
after subjecting it to the patenting treatment.
(MPa) (MPa)
4.4 The width to thickness ratio of the wire cross section
Class 1 Class 2 Class 1 Class 2 Class 1 Class 2
0.020 (051) 296 (2045) 268 (1850) 260 (1795) 232 (1600) 4.0 5.0
shall not exceed 8.
0.030 (0.76) 290 (2000) 262 (1810) 255 (1760) 226 (1560) 4.0
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A905–04 Designation: A905 – 04 (Reapproved 2010)
Standard Specification for
1
Steel Wire, Pressure Vessel Winding
This standard is issued under the fixed designation A905; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope *
1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with
rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text
and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each
system must be used independent of the other. Combining values from the two systems may result in nonconformance with the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A510 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel (Metric)
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
3
E30 Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron and Wrought Iron
E309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
2.2 Military Standard:
4
MIL-STD-163 Steel Mill Products, Preparation for Shipment and Storage
2.3 Federal Standard:
6
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.4 AIAG Standard:
5
AIAGB-5 02.00 Primary Metals Identification Tag Application Standard
3. Ordering Information
3.1 It shall be the responsibility of the purchaser to specify all requirements that are necessary for material under this
specification. Such requirements may include, but are not limited to, the following:
3.1.1 Quantity (mass),
3.1.2 Name of material,
3.1.3 Dimensions (see Section 7),
3.1.4 Finish (see Section 8),
3.1.5 Packaging (see Section 11),
3.1.6 Cast or heat analysis report (see Section 5),
3.1.7 Number of certification or test reports required (see Section 10),
3.1.8 ASTM designation and year of issue, and
3.1.9 Supplementary requirements, if any.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.03
on Steel Rod and Wire.
Current edition approved Sept.April 1, 2004.2010. Published September 2004.April 2010. Originally approved in 1991. Last previous edition approved in 19982004 as
A905–93(1998).A905 – 04. DOI: 10.1520/A0905-04R10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
5
Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd., Suite 200, Southfield, MI 48034.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A905 – 04 (2010)
4. Material and Manufacture
4.1 The steel shall be produced by any of the following primary processes: (1) basic oxygen, and (2) electric furnace or vacuum
induction (VIM). The primary melting may incorporate separate degassing or refining and may be followed by secondary melting
by the electrode slag process (ESR) or the vacuum arc remelting process (VAR).
4.1.1 The steel may be ingot cast or continuously cast.
4.2 The finished wire shall be free from detrimental pipe and undue segregation.
4.3 The wire shall be cold drawn or cold rolled, or both, to produce the desired mechanical properties and dimensions after
subjecting it to the patenting treatment.
4.4 The width to thickness ratio of the wire cross section shall n
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A905–04 Designation: A905 – 04 (Reapproved 2010)
Standard Specification for
1
Steel Wire, Pressure Vessel Winding
This standard is issued under the fixed designation A905; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope *
1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with
rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text
and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each
system must be used independent of the other. Combining values from the two systems may result in nonconformance with the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A510 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel (Metric)
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
3
E30 Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron and Wrought Iron
E309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
2.2 Military Standard:
4
MIL-STD-163 Steel Mill Products, Preparation for Shipment and Storage
2.3 Federal Standard:
6
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.4 AIAG Standard:
5
AIAGB-5 02.00 Primary Metals Identification Tag Application Standard
3. Ordering Information
3.1 It shall be the responsibility of the purchaser to specify all requirements that are necessary for material under this
specification. Such requirements may include, but are not limited to, the following:
3.1.1 Quantity (mass),
3.1.2 Name of material,
3.1.3 Dimensions (see Section 7),
3.1.4 Finish (see Section 8),
3.1.5 Packaging (see Section 11),
3.1.6 Cast or heat analysis report (see Section 5),
3.1.7 Number of certification or test reports required (see Section 10),
3.1.8 ASTM designation and year of issue, and
3.1.9 Supplementary requirements, if any.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.03
on Steel Rod and Wire.
Current edition approved Sept.April 1, 2004.2010. Published September 2004.April 2010. Originally approved in 1991. Last previous edition approved in 19982004 as
A905–93(1998).A905 – 04. DOI: 10.1520/A0905-04R10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
5
Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd., Suite 200, Southfield, MI 48034.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A905 – 04 (2010)
4. Material and Manufacture
4.1 The steel shall be produced by any of the following primary processes: (1) basic oxygen, and (2) electric furnace or vacuum
induction (VIM). The primary melting may incorporate separate degassing or refining and may be followed by secondary melting
by the electrode slag process (ESR) or the vacuum arc remelting process (VAR).
4.1.1 The steel may be ingot cast or continuously cast.
4.2 The finished wire shall be free from detrimental pipe and undue segregation.
4.3 The wire shall be cold drawn or cold rolled, or both, to produce the desired mechanical properties and dimensions after
subjecting it to the patenting treatment.
4.4 The width to thickness ratio of the wire cross section shall not exceed 8.
5. Chemical Composition
5.1 The steel shall conform to
...