A01.03 - Steel Rod and Wire

ABSTRACT
This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs that are not subject to high stress or requiring high fatigue properties and wire forms. The steel specimens shall either be ingot cast or strand cast. Cast or heat and product analysis shall be performed wherein steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Specimens shall also undergo tension and wrap tests and shall conform to the requirements of tensile properties.
SCOPE
1.1 This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs, rings, and wire forms that are not subject to high stress or requiring high fatigue properties.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification deals with the general requirements for round carbon spring steel wire coils intended for the manufacture of mechanical springs and wire forms that are heat treated after fabrication. Heat treatment processes include austenitizing, quenching and tempering. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace process and the wire shall be thermally treated, or thermally treated and drawn. Product analysis, wrap testing, and chemical analysis shall be performed and materials shall conform to the requirements for chemical composition, metallurgical structure and mechanical properties such as tensile strength. Packaging of the coils of wire shall be by agreement between the manufacturer and the purchaser wherein the agreement shall include coil dimensions and weights, while marking and bar coding for identification shall be by tag securely attached to each coil of wire.
SCOPE
1.1 This specification covers round carbon spring steel wire in coils intended for the manufacture of mechanical springs and wire forms that are heat treated (austenitized, quenched, and tempered) after fabrication.  
1.2 The values stated in inch-pound units are to be regarded as the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers round, shaped and flat rolled plain carbon and alloy steel spring wires, uniform in quality and temper, intended for the manufacture of mechanical springs that can withstand moderate fatigue stresses over some relatively low number of cycles. This wire shall be either in the annealed and cold-drawn or oil-tempered conditions. The steel may be made by any commercially accepted steel making process in either ingot cast or strand cast form. The percentage of the following elements: carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium, shall conform to the chemical composition requirements and be determined by heat analysis. Tensile and wrap tests shall conform to the mechanical requirements such as tensile strength. Metallurgical requirements including eddy current testing for etched surface, decarburization, and inclusion content are detailed.
SCOPE
1.1 This specification covers four different grades of round and shaped plain carbon and alloy steel spring wire, uniform in quality and temper, intended for the manufacture of mechanical springs that can withstand moderate fatigue stresses over some relatively low number of cycles. The quality level is between the commercial quality grades of wire such as Specifications A401/A401M, A231/A231M, and A229/A229M and the valve spring quality grades such Specifications as A230/A230M, A232/A232M, and A877/A877M. It is similar to the grade TD (referenced in EN 10270-2) intended for medium fatigue levels, such as required for clutch springs. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the highest quality of round chromium-silicon alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition. The steel may be made by any commercially accepted steel making process, shall be continuously cast, and shall be free from detrimental pipe and undue segregation and surface imperfections. Heat analysis, tensile testing, wrap testing, and surface inspection by magnetic or eddy current defect analysis shall be done. Both heat and product analysis shall conform to the chemical composition requirements specified for carbon, manganese, phosphorus, sulfur, silicon, and chromium. The mechanical requirements for the steel wire including cooling, heat treatment, and tensile strength, and the metallurgical requirements including etched surface testing, decarburization, and inclusion content are detailed.
SCOPE
1.1 This specification covers the highest quality of round and shaped chromium-silicon and chromium-silicon-vanadium alloys of steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers round, cold-drawn, steel spring wire having properties and quality intended for the manufacture of the following types of upholstery springs:  
1.1.1 Type A—Coiled (Marshall pack),  
1.1.2 Type B—Coiled and knotted,  
1.1.3 Type C—Coiled and knotted (offset style),  
1.1.4 Type D—Coiled and hooked (single and cross helicals),  
1.1.5 Type E—Coiled and hooked (short tension—regular tensile strength),  
1.1.6 Type F—Coiled and hooked (short tension—high tensile strength),  
1.1.7 Type G—Regular lacing,  
1.1.8 Type H—Automatic lacing,  
1.1.9 Type I—Zig-zag (U-formed),  
1.1.10 Type J—Square-formed, and  
1.1.11 Type K—Sinuous for furniture spring units.  
1.2 These types of upholstery springs are used in the manufacture of automotive seat springs, furniture springs, bed spring units, mattresses, furniture cushions, and automobile seats. This wire is not intended for the manufacture of mechanical springs.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers uncoated and four classes of round, metallic coated, cold-drawn, carbon steel wire rope in five strength levels. The following materials testing procedures shall be conducted: standard tensile testing; alternate tensile testing; torsion testing; and wrap testing. The wire diameter tolerances of uncoated, drawn-galvanized or drawn-Zn5 Al-MM, and final-galvanized or final-coated Zn5 Al-MM rope wires shall be described. Minimum breakage forces for the carbon steel wire rope shall also be presented. During torsion testing, varying amounts of load shall be applied to the wire being tested.
SCOPE
1.1 This specification covers uncoated and metallic coated classes of round, cold-drawn, carbon steel wire for wire rope in five strength levels. This specification specifies:  
1.1.1 Dimensional tolerances,  
1.1.2 Mechanical characteristics,  
1.1.3 Chemical composition requirements,  
1.1.4 Coating requirements (if applicable), and  
1.1.5 Packaging requirements.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers stranded steel wire ropes of various grades and constructions manufactured from uncoated or metallic coated wire and cord products manufactured from metallic coated wire. Dimensional characteristics include the diameter and lay length of the rope. Mechanical property requirements include: rope breaking force, spinning loss factor, and stretch; and wire torsions, tensile strength, tensile grade, and level. Cores of stranded ropes shall normally either be of steel or fiber composition. All wire ropes shall be lubricated and impregnated in the manufacturing process. Wire finish may be final-galvanized rope or drawn-galvanized (zinc coated) rope. Rope workmanship and finish; testing and compliance; acceptance tests; and packaging and identification are also detailed.
SCOPE
1.1 This specification covers the general requirements for the more common types of steel wire ropes. Included in this specification are wire ropes in various grades and constructions from 1/4 to 31/2 in. [6 to 89 mm] manufactured from uncoated or metallic coated wire. Also included are cord products from 1/32 to 3/8 in. [0.8 to 10 mm] manufactured from metallic coated wire. For specific applications, additional or alternative requirements may apply.  
1.2 The values stated in either inch-pounds or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers epoxy-coated steel wires, in coils, for general use. The protective epoxy coatings covered here are available in three classes, namely: Class A, which are intended for use in moderate corrosion protection; Class B, which are intended for more severe protection; and Class C, which are intended for severe corrosion and abrasion protection. Prior to cleaning and coating, the steel wires shall be free of surface contaminants such as oil, grease, or paint. Wire surfaces shall be cleaned by abrasive cleaning or chemical cleaning to ensure proper adherence of the epoxy. Coatings shall then be applied as soon as possible after cleaning, before possible oxidation, and shall be properly cured. Wrap, bend and tensile tests shall be performed in order to evaluate coating properties, including thickness, continuity, adherence, size tolerance, and tensile strength.
SCOPE
1.1 This specification covers steel wire in the size range of 0.120 to 0.500 in. (3.05 to 12.7 mm) with three classes of protective epoxy coating, in coils, for general use. Class A coating is intended for use for moderate corrosion protection, Class B coating for more severe protection, and Class C for severe corrosion and abrasion protection.  
Note 1: The coating applicator is identified throughout this specification as the manufacturer.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths. Chemical compositions are specified by ranges or limits for carbon and other elements. The grades commonly specified for carbon steel wire rods and coarse round wire are presented. Grain size, when specified, and the mechanical properties enumerated in individual specifications shall be determined in accordance with reference test materials.
SCOPE
1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.  
1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, inch-pound units are shown in brackets.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification deals with the highest quality of round carbon steel spring wire, uniform in quality and temper, intended especially for the manufacture of valve springs and other springs requiring high-fatigue properties. The steel wire shall be subjected to continuous casting, hardening, and tempering to produce the desired mechanical properties. The steel shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, and silicon. Mechanical properties shall be determined by the tension test, wrap test, twist test, and special surface inspection. The material as represented by tension test specimens shall conform to the tensile requirements for tensile strength and reduction of area. Metallurgical characterization of steel shall include decarburization, surface condition, and microstructure.
SCOPE
1.1 This specification covers the highest quality of round and shaped carbon steel spring wire, uniform in quality and temper, intended especially for the manufacture of valve springs and other springs requiring high-fatigue properties. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers carbon steel wire coils for general use. Steel samples shall be hard drawn, annealed in process, or annealed at finish size. The steel shall either be ingot cast or strand cast. The carbon steel shall also undergo tensile tests and shall conform to the required values of tensile strength. Final products shall be marked either by a tag or bar code.
SCOPE
1.1 This specification covers carbon steel wire, supplied in coils, for general use. It may be produced hard drawn, annealed in process, or annealed at finish size.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the highest quality of round modified chromium vanadium alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall either be in the annealed and cold-drawn or oil-tempered condition. The steel shall be subjected to continuous casting and be free from detrimental pipe and undue segregation. Heat and product analysis shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium. Mechanical properties shall be determined by the following: annealing and cold-drawing, oil tempering, wrap testing, and special surface inspection. In the oil-tempered condition, steel shall conform to the tensile requirements for different wire diameters. Metallurgical characterization shall include surface condition, decarburization, and inclusion content. The wire or wire rod shall conform to the maximum inclusion content requirements for the surface and core zones.
SCOPE
1.1 This specification covers the highest quality of round and shaped modified chromium vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independent of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers high strength, cold drawn or cold rolled steel wire with rectangular cross-section and round mill edge. The wire is intended for use in pre-stressed vessel and press frame windings. The steel shall be manufactured by basic oxygen, electric furnace, or vacuum induction processes and produced as ingot cast or continuous cast. Materials shall be tested for contents of carbon, manganese, phosphorus, sulphur, and silicon. A tension tests shall also be performed to evaluate mechanical properties conformance. Guidelines for workmanship, finish, and appearance are stated, as well as the inspection, certification of reports, packaging, marking, and loading for shipment.
SCOPE
1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings.  
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers round chromium-silicon alloy steel spring wire having properties and quality intended for the manufacture of springs resistant to set when used at moderately elevated temperatures. This product is not meant to be used for high cycle fatigue applications. Either ingot or strand cast steel may be made by any commercially accepted steel making process. The steel shall conform on heat and product analysis to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, silicon and chromium. Annealed and cold drawn or oil-tempered wires shall conform to the specified mechanical properties including tensile strength. Requirements for tension and wrap tests as well as metallurgical requirements for etched surface testing and decarburization are detailed.
SCOPE
1.1 This specification covers round and shaped chromium-silicon alloy steel spring wire having properties and quality intended for the manufacture of springs resistant to set when used at moderately elevated temperatures. This product is not meant to be used for non-static applications involving moderate fatigue stresses (see Specification A1000/A1000M) or high cycle fatigue applications (see Specification A877/A877M). This wire shall be provided either in the annealed and cold-drawn or quench and tempered condition as specified by the purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.2.1 Within the text, the inch-pound units are shown in brackets.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the highest quality of round chromium-vanadium alloy steel wires for manufacture of valve springs and other springs with high-fatigue properties under moderately elevated temperatures. The wires shall be annealed, cold-drawn, or oil-tempered. The material shall conform to specified carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium contents. Guidelines for mechanical testing are given. Values for tensile requirements are provided. Material decarburization shall be examined. Attention is also given to workmanship, finish, and appearance of the product, and as well as its inspection, rejection, rehearing, and certification. Packaging, marking, and loading for shipment is also described.
SCOPE
1.1 This specification covers the highest quality of round and shaped chromium-vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers round chromium-vanadium alloy steel spring wires having properties and quality intended for the manufacture of springs used at moderately elevated temperatures. Wires shall either be in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser. The steel may either be ingot cast or strand cast, and the finished wire shall be free from detrimental pipe and undue segregation. Specimens shall undergo cast or heat analysis, and shall conform to required chemical compositions for carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium. Wrap tests shall also be performed wherein mechanical properties shall be assessed for tensile strength requirements. Metallurgical properties, such as the surface condition and decarburization, shall be inspected as well. For all test procedures, one specimen shall be taken for each ten coils, or fraction thereof, in a lot. Each cast or heat in a given lot shall be tested.
SCOPE
1.1 This specification covers round and shaped chromium-vanadium alloy steel spring wire having properties and quality intended for the manufacture of springs used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.2.1 Within the text, the inch-pound units are shown in brackets.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers high quality, round, cold-drawn steel music spring quality wire for the manufacture of springs subject to high stresses or requiring good fatigue properties. The steel shall either be ingot cast or strand cast. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Steel specimens shall also undergo tension test, wrap test, and torsion tests. Final products shall be marked by a tag.
SCOPE
1.1 This specification covers two types of round, cold-drawn steel music spring quality wire, uniform in mechanical properties, intended especially for the manufacture of springs subject to high stresses or requiring good fatigue properties.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers two classes of oil-tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms. The steel may be made by any commercially accepted steel-making process and shall either be ingot cast or strand cast. The finished wire shall be free of detrimental pipe and undue segregation. The wire shall be oil quenched and tempered to produce the desired mechanical properties such as tensile strength. Cast, heat, and product analysis shall conform to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, and silicon. Tension, wrap, and surface tests shall be performed. The surface of the wire as-received shall be free of rust, excessive scale die marks, pits, and scratches detrimental to the end application. Other metallurgical requirements such as microstructure and decarburization are detailed.
SCOPE
1.1 This specification covers two classes of commercial quality round and shaped quenched and tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms. The quality level is lower than specialty spring quality (Specification A1000/A1000M) or valve spring quality (Specification A230/A230M).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems can result in non-conformance with the standard. Within the text, the inch-pound units are shown in brackets.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Tension tests are generally to be performed on new wire ropes. The use of wire rope in any application can reduce individual wire strengths due to abrasion and nicking that will result in the wire rope strength being reduced. Damage to the outer wires will also lower the maximum strength achieved during tension testing.  
4.2 The modulus of elasticity of wire rope is not considered to be a standard requirement at this time. The determination of this material property requires specialized equipment and techniques.  
4.3 Rope to be tested should be thoroughly examined to verify that no external wire damage is present. If present, it should be noted. When possible, a new undamaged sample should be obtained for testing.  
4.4 End attachments and their installation can directly affect breaking force achieved during testing. Any attachment that can be used to directly achieve the required rope breaking force can be used. Standard testing with a poured socket, using zinc, white metal or thermoset resin, has been considered the most efficient. Proficiency in attachment of any fitting can have a direct effect on the final test results.
SCOPE
1.1 This test method covers the tension testing of wire ropes and strand at room temperature, specifically to determine the measured breaking force, yield strength, elongation, and modulus of elasticity. Methods described in this standard are not intended for other purposes.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 1  and Note 2.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 The complex stress and strain conditions that occur in the sample during the torsion test are sensitive to minor variations in materials, making the torsion test a useful tool in assessing wire ductility under torsional loading.
SCOPE
1.1 This test method describes the torsion (or twist) testing of metallic wire.  
1.2 The values stated in U.S. customary units are to be regarded as the standard. The SI equivalents of U.S. customary units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers round, uncoated, high tensile strength, cold-drawn steel spring wires having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both. The steel shall be made by any commercially accepted steel making process. The steel shall either be ingot cast or continuous strand cast. The finished wire shall be free from detrimental pipe and undue segregation. The wire shall be cold drawn to produce the desired tensile strength. The wire finish shall be suitable for forming or coiling. It is not intended that this material be furnished with a metallic coating. Heat and product analysis shall be conducted wherein the material shall conform to the required chemical composition values of carbon, manganese, phosphorus, sulfur, and silicon. The material shall undergo tensile and wrap tests. The steel shall have fine pearlite microstructure and the wire surface shall not exhibit imperfections.
SCOPE
1.1 This specification covers round, uncoated, high tensile strength, cold drawn steel spring wire, having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers stranded steel wire ropes of various grades and constructions manufactured from uncoated or metallic coated wire and cord products manufactured from metallic coated wire. Dimensional characteristics include the diameter and lay length of the rope. Mechanical property requirements include: rope breaking force, spinning loss factor, and stretch; and wire torsions, tensile strength, tensile grade, and level. Cores of stranded ropes shall normally either be of steel or fiber composition. All wire ropes shall be lubricated and impregnated in the manufacturing process. Wire finish may be final-galvanized rope or drawn-galvanized (zinc coated) rope. Rope workmanship and finish; testing and compliance; acceptance tests; and packaging and identification are also detailed.
SCOPE
1.1 This specification covers the general requirements for the more common types of steel wire ropes. Included in this specification are wire ropes in various grades and constructions from 1/4 in. [6 mm] to 31/2 in. [89 mm] manufactured from uncoated or metallic coated wire. Also included are cord products from 1/32 in. [0.8 mm] to 3/8 in. [10 mm] manufactured from metallic coated wire. For specific applications, additional or alternative requirements may apply.  
1.2 The values stated in either inch-pounds or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths. Chemical compositions are specified by ranges or limits for carbon and other elements. The grades commonly specified for carbon steel wire rods and coarse round wire are presented. Grain size, when specified, and the mechanical properties enumerated in individual specifications shall be determined in accordance with reference test materials.
SCOPE
1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.  
1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers round, cold-drawn, steel spring wire having properties and quality intended for the manufacture of the following types of upholstery springs:  
1.1.1 Type A—Coiled (Marshall pack),  
1.1.2 Type B—Coiled and knotted,  
1.1.3 Type C—Coiled and knotted (offset style),  
1.1.4 Type D—Coiled and hooked (single and cross helicals),  
1.1.5 Type E—Coiled and hooked (short tension—regular tensile strength),  
1.1.6 Type F—Coiled and hooked (short tension—high tensile strength),  
1.1.7 Type G—Regular lacing,  
1.1.8 Type H—Automatic lacing,  
1.1.9 Type I—Zig-zag (U-formed),  
1.1.10 Type J—Square-formed, and  
1.1.11 Type K—Sinuous for furniture spring units.  
1.2 These types of upholstery springs are used in the manufacture of automotive seat springs, furniture springs, bed spring units, mattresses, furniture cushions, and automobile seats. This wire is not intended for the manufacture of mechanical springs.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers two classes of oil-tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms. The steel may be made by any commercially accepted steel-making process and shall either be ingot cast or strand cast. The finished wire shall be free of detrimental pipe and undue segregation. The wire shall be oil quenched and tempered to produce the desired mechanical properties such as tensile strength. Cast, heat, and product analysis shall conform to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, and silicon. Tension, wrap, and surface tests shall be performed. The surface of the wire as-received shall be free of rust, excessive scale die marks, pits, and scratches detrimental to the end application. Other metallurgical requirements such as microstructure and decarburization are detailed.
SCOPE
1.1 This specification covers two classes of commercial quality round and shaped quenched and tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms. The quality level is lower than specialty spring quality (Specification A1000/A1000M) or valve spring quality (Specification A230/A230M).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems can result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs that are not subject to high stress or requiring high fatigue properties and wire forms. The steel specimens shall either be ingot cast or strand cast. Cast or heat and product analysis shall be performed wherein steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Specimens shall also undergo tension and wrap tests and shall conform to the requirements of tensile properties.
SCOPE
1.1 This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs, rings, and wire forms that are not subject to high stress or requiring high fatigue properties.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers high strength, cold drawn or cold rolled steel wire with rectangular cross-section and round mill edge. The wire is intended for use in pre-stressed vessel and press frame windings. The steel shall be manufactured by basic oxygen, electric furnace, or vacuum induction processes and produced as ingot cast or continuous cast. Materials shall be tested for contents of carbon, manganese, phosphorus, sulphur, and silicon. A tension tests shall also be performed to evaluate mechanical properties conformance. Guidelines for workmanship, finish, and appearance are stated, as well as the inspection, certification of reports, packaging, marking, and loading for shipment.
SCOPE
1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings.  
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the highest quality of round modified chromium vanadium alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall either be in the annealed and cold-drawn or oil-tempered condition. The steel shall be subjected to continuous casting and be free from detrimental pipe and undue segregation. Heat and product analysis shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium. Mechanical properties shall be determined by the following: annealing and cold-drawing, oil tempering, wrap testing, and special surface inspection. In the oil-tempered condition, steel shall conform to the tensile requirements for different wire diameters. Metallurgical characterization shall include surface condition, decarburization, and inclusion content. The wire or wire rod shall conform to the maximum inclusion content requirements for the surface and core zones.
SCOPE
1.1 This specification covers the highest quality of round and shaped modified chromium vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independent of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers round, shaped and flat rolled plain carbon and alloy steel spring wires, uniform in quality and temper, intended for the manufacture of mechanical springs that can withstand moderate fatigue stresses over some relatively low number of cycles. This wire shall be either in the annealed and cold-drawn or oil-tempered conditions. The steel may be made by any commercially accepted steel making process in either ingot cast or strand cast form. The percentage of the following elements: carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium, shall conform to the chemical composition requirements and be determined by heat analysis. Tensile and wrap tests shall conform to the mechanical requirements such as tensile strength. Metallurgical requirements including eddy current testing for etched surface, decarburization, and inclusion content are detailed.
SCOPE
1.1 This specification covers four different grades of round and shaped plain carbon and alloy steel spring wire, uniform in quality and temper, intended for the manufacture of mechanical springs that can withstand moderate fatigue stresses over some relatively low number of cycles. The quality level is between the commercial quality grades of wire such as Specifications A401/A401M, A231/A231M, and A229/A229M and the valve spring quality grades such Specifications as A230/A230M, A232/A232M, and A877/A877M. It is similar to the grade TD (referenced in EN 10270-2) intended for medium fatigue levels, such as required for clutch springs. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification deals with the general requirements for round carbon spring steel wire coils intended for the manufacture of mechanical springs and wire forms that are heat treated after fabrication. Heat treatment processes include austenitizing, quenching and tempering. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace process and the wire shall be thermally treated, or thermally treated and drawn. Product analysis, wrap testing, and chemical analysis shall be performed and materials shall conform to the requirements for chemical composition, metallurgical structure and mechanical properties such as tensile strength. Packaging of the coils of wire shall be by agreement between the manufacturer and the purchaser wherein the agreement shall include coil dimensions and weights, while marking and bar coding for identification shall be by tag securely attached to each coil of wire.
SCOPE
1.1 This specification covers round carbon spring steel wire in coils intended for the manufacture of mechanical springs and wire forms that are heat treated (austenitized, quenched, and tempered) after fabrication.  
1.2 The values stated in inch-pound units are to be regarded as the standard.

ABSTRACT
This specification covers carbon steel wire coils for general use. Steel samples shall be hard drawn, annealed in process, or annealed at finish size. The steel shall either be ingot cast or strand cast. The carbon steel shall also undergo tensile tests and shall conform to the required values of tensile strength. Final products shall be marked either by a tag or bar code.
SCOPE
1.1 This specification covers carbon steel wire, supplied in coils, for general use. It may be produced hard drawn, annealed in process, or annealed at finish size.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

ABSTRACT
This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs that are not subject to high stress or requiring high fatigue properties and wire forms. The steel specimens shall either be ingot cast or strand cast. Cast or heat and product analysis shall be performed wherein steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Specimens shall also undergo tension and wrap tests and shall conform to the requirements of tensile properties.
SCOPE
1.1 This specification covers two classes of round cold-drawn steel spring wire having properties and quality for the manufacture of mechanical springs that are not subject to high stress or requiring high fatigue properties and wire forms.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification covers the highest quality of round chromium-silicon alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition. The steel may be made by any commercially accepted steel making process, shall be continuously cast, and shall be free from detrimental pipe and undue segregation and surface imperfections. Heat analysis, tensile testing, wrap testing, and surface inspection by magnetic or eddy current defect analysis shall be done. Both heat and product analysis shall conform to the chemical composition requirements specified for carbon, manganese, phosphorus, sulfur, silicon, and chromium. The mechanical requirements for the steel wire including cooling, heat treatment, and tensile strength, and the metallurgical requirements including etched surface testing, decarburization, and inclusion content are detailed.
SCOPE
1.1 This specification covers the highest quality of round and shaped chromium-silicon and chromium-silicon-vanadium alloys of steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification covers high quality, round, cold-drawn steel music spring quality wire for the manufacture of springs subject to high stresses or requiring good fatigue properties. The steel shall either be ingot cast or strand cast. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Steel specimens shall also undergo tension test, wrap test, and torsion tests. Final products shall be marked by a tag.
SCOPE
1.1 This specification covers two types of round, cold-drawn steel music spring quality wire, uniform in mechanical properties, intended especially for the manufacture of springs subject to high stresses or requiring good fatigue properties.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification covers the highest quality of round chromium-silicon alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition. The steel may be made by any commercially accepted steel making process, shall be continuously cast, and shall be free from detrimental pipe and undue segregation and surface imperfections. Heat analysis, tensile testing, wrap testing, and surface inspection by magnetic or eddy current defect analysis shall be done. Both heat and product analysis shall conform to the chemical composition requirements specified for carbon, manganese, phosphorus, sulfur, silicon, and chromium. The mechanical requirements for the steel wire including cooling, heat treatment, and tensile strength, and the metallurgical requirements including etched surface testing, decarburization, and inclusion content are detailed.
SCOPE
1.1 This specification covers the highest quality of round and shaped chromium-silicon and chromium-silicon-vanadium alloys of steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. It is similar to the grade VD (referenced in EN 10270-2) intended for high fatigue levels. This wire shall be either in the annealed and cold-drawn or quenched and tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification covers round chromium-silicon alloy steel spring wire having properties and quality intended for the manufacture of springs resistant to set when used at moderately elevated temperatures. This product is not meant to be used for high cycle fatigue applications. Either ingot or strand cast steel may be made by any commercially accepted steel making process. The steel shall conform on heat and product analysis to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, silicon and chromium. Annealed and cold drawn or oil-tempered wires shall conform to the specified mechanical properties including tensile strength. Requirements for tension and wrap tests as well as metallurgical requirements for etched surface testing and decarburization are detailed.
SCOPE
1.1 This specification covers round and shaped chromium-silicon alloy steel spring wire having properties and quality intended for the manufacture of springs resistant to set when used at moderately elevated temperatures. This product is not meant to be used for non-static applications involving moderate fatigue stresses (see Specification A1000/A1000M) or high cycle fatigue applications (see Specification A877/A877M). This wire shall be provided either in the annealed and cold-drawn or quench and tempered condition as specified by the purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.2.1 Within the text, the inch-pound units are shown in brackets.

ABSTRACT
This specification covers round chromium-vanadium alloy steel spring wires having properties and quality intended for the manufacture of springs used at moderately elevated temperatures. Wires shall either be in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser. The steel may either be ingot cast or strand cast, and the finished wire shall be free from detrimental pipe and undue segregation. Specimens shall undergo cast or heat analysis, and shall conform to required chemical compositions for carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium. Wrap tests shall also be performed wherein mechanical properties shall be assessed for tensile strength requirements. Metallurgical properties, such as the surface condition and decarburization, shall be inspected as well. For all test procedures, one specimen shall be taken for each ten coils, or fraction thereof, in a lot. Each cast or heat in a given lot shall be tested.
SCOPE
1.1 This specification covers round and shaped chromium-vanadium alloy steel spring wire having properties and quality intended for the manufacture of springs used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.2.1 Within the text, the inch-pound units are shown in brackets.

ABSTRACT
This specification covers stranded steel wire ropes of various grades and constructions manufactured from uncoated or metallic coated wire and cord products manufactured from metallic coated wire. Dimensional characteristics include the diameter and lay length of the rope. Mechanical property requirements include: rope breaking force, spinning loss factor, and stretch; and wire torsions, tensile strength, tensile grade, and level. Cores of stranded ropes shall normally either be of steel or fiber composition. All wire ropes shall be lubricated and impregnated in the manufacturing process. Wire finish may be final-galvanized rope or drawn-galvanized (zinc coated) rope. Rope workmanship and finish; testing and compliance; acceptance tests; and packaging and identification are also detailed.
SCOPE
1.1 This specification covers the general requirements for the more common types of stranded steel wire ropes. Included in this specification are wire ropes in various grades and constructions from 1/4 in. [6 mm] to 23/8 in. [60 mm] manufactured from uncoated or metallic coated wire. Also included are cord products from 1/32 in. [0.8 mm] to 3/8 in. [10 mm] manufactured from metallic coated wire. For specific applications, additional or alternative requirements may apply.  
1.2 The values stated in either inch-pounds or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

ABSTRACT
This specification covers uncoated and four classes of round, metallic coated, cold-drawn, carbon steel wire rope in five strength levels. The following materials testing procedures shall be conducted: standard tensile testing; alternate tensile testing; torsion testing; and wrap testing. The wire diameter tolerances of uncoated, drawn-galvanized or drawn-Zn5 Al-MM, and final-galvanized or final-coated Zn5 Al-MM rope wires shall be described. Minimum breakage forces for the carbon steel wire rope shall also be presented. During torsion testing, varying amounts of load shall be applied to the wire being tested.
SCOPE
1.1 This specification covers uncoated and four classes of round, metallic coated, cold-drawn, carbon steel wire for wire rope in five strength levels. This specification specifies:  
1.1.1 Dimensional tolerances,  
1.1.2 Mechanical characteristics,  
1.1.3 Chemical composition requirements,  
1.1.4 Coating requirements (if applicable), and  
1.1.5 Packaging requirements.  
1.2 The values stated for metric equivalents are provided for informational purposes only.

ABSTRACT
This specification covers high quality, round, cold-drawn steel music spring quality wire for the manufacture of springs subject to high stresses or requiring good fatigue properties. The steel shall either be ingot cast or strand cast. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, and silicon. Steel specimens shall also undergo tension test, wrap test, and torsion tests. Final products shall be marked by a tag.
SCOPE
1.1 This specification covers a high quality, round, cold-drawn steel music spring quality wire, uniform in mechanical properties, intended especially for the manufacture of springs subject to high stresses or requiring good fatigue properties.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification covers epoxy-coated steel wires, in coils, for general use. The protective epoxy coatings covered here are available in three classes, namely: Class A, which are intended for use in moderate corrosion protection; Class B, which are intended for more severe protection; and Class C, which are intended for severe corrosion and abrasion protection. Prior to cleaning and coating, the steel wires shall be free of surface contaminants such as oil, grease, or paint. Wire surfaces shall be cleaned by abrasive cleaning or chemical cleaning to ensure proper adherence of the epoxy. Coatings shall then be applied as soon as possible after cleaning, before possible oxidation, and shall be properly cured. Wrap, bend and tensile tests shall be performed in order to evaluate coating properties, including thickness, continuity, adherence, size tolerance, and tensile strength.
SCOPE
1.1 This specification covers steel wire in the size range of 0.120 to 0.500 in. (3.05 to 12.7 mm) with three classes of protective epoxy coating, in coils, for general use. Class A coating is intended for use for moderate corrosion protection, Class B coating for more severe protection, and Class C for severe corrosion and abrasion protection. Note 1—The coating applicator is identified throughout this specification as the manufacturer.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

ABSTRACT
This specification covers the general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths. Chemical compositions are specified by ranges or limits for carbon and other elements. The grades commonly specified for carbon steel wire rods and coarse round wire are presented. Grain size, when specified, and the mechanical properties enumerated in individual specifications shall be determined in accordance with reference test materials.
SCOPE
1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.  
1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

SIGNIFICANCE AND USE
4.1 Wire rope tests are generally to be performed on new rope. The use of wire rope in any application can reduce individual wire strengths due to abrasion and nicking that will result in the wire rope strength being reduced. Damage to the outer wires will also lower the maximum strength achieved during tension testing.  
4.2 The modulus of elasticity of wire rope is not considered to be a standard requirement at this time. The determination of this material property requires specialized equipment and techniques.  
4.3 Rope to be tested should be thoroughly examined to verify that no external wire damage is present. If present, it should be noted. When possible, a new undamaged sample should be obtained for testing.  
4.4 End attachments and their installation can directly affect breaking force achieved during testing. Any attachment that can be used to directly achieve the required rope breaking force can be used. Standard testing with a poured socket, using zinc, white metal or thermoset resin, has been considered the most efficient. Proficiency in attachment of any fitting can have a direct effect on the final test results.
SCOPE
1.1 This test method covers the tension testing of wire ropes and strand at room temperature, specifically to determine the measured breaking force, yield strength, elongation, and modulus of elasticity. Methods described in this standard are not intended for other purposes.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 1 and Note 2.

SCOPE
1.1 This specification covers round, cold-drawn, steel spring wire having properties and quality intended for the manufacture of the following types of upholstery springs:  
1.1.1 Type A—Coiled (Marshall pack),  
1.1.2 Type B—Coiled and knotted,  
1.1.3 Type C—Coiled and knotted (offset style),  
1.1.4 Type D—Coiled and hooked (single and cross helicals),  
1.1.5 Type E—Coiled and hooked (short tension—regular tensile strength),  
1.1.6 Type F—Coiled and hooked (short tension—high tensile strength),  
1.1.7 Type G—Regular lacing,  
1.1.8 Type H—Automatic lacing,  
1.1.9 Type I—Zig-zag (U-formed),  
1.1.10 Type J—Square-formed, and  
1.1.11 Type K—Sinuous for furniture spring units.  
1.2 These types of upholstery springs are used in the manufacture of automotive seat springs, furniture springs, bed spring units, mattresses, furniture cushions, and automobile seats. This wire is not intended for the manufacture of mechanical springs.

SIGNIFICANCE AND USE
4.1 The complex stress and strain conditions that occur in the sample during the torsion test are sensitive to minor variations in materials, making the torsion test a useful tool in assessing wire ductility under torsional loading.
SCOPE
1.1 This test method describes the torsion (or twist) testing of metallic wire.  
1.2 The values stated in U.S. customary units are to be regarded as the standard. The SI equivalents of U.S. customary units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers two classes of oil-tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms. The steel may be made by any commercially accepted steel-making process and shall either be ingot cast or strand cast. The finished wire shall be free of detrimental pipe and undue segregation. The wire shall be oil quenched and tempered to produce the desired mechanical properties such as tensile strength. Cast, heat, and product analysis shall conform to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, and silicon. Tension, wrap, and surface tests shall be performed. The surface of the wire as-received shall be free of rust, excessive scale die marks, pits, and scratches detrimental to the end application. Other metallurgical requirements such as microstructure and decarburization are detailed.
SCOPE
1.1 This specification covers two classes of round and shaped quenched and tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems can result in non-conformance with the standard.

ABSTRACT
This specification covers round, uncoated, high tensile strength, cold-drawn steel spring wires having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both. The steel shall be made by any commercially accepted steel making process. The steel shall either be ingot cast or continuous strand cast. The finished wire shall be free from detrimental pipe and undue segregation. The wire shall be cold drawn to produce the desired tensile strength. The wire finish shall be suitable for forming or coiling. It is not intended that this material be furnished with a metallic coating. Heat and product analysis shall be conducted wherein the material shall conform to the required chemical composition values of carbon, manganese, phosphorus, sulfur, and silicon. The material shall undergo tensile and wrap tests. The steel shall have fine pearlite microstructure and the wire surface shall not exhibit imperfections.
SCOPE
1.1 This specification covers round, uncoated, high tensile strength, cold-drawn steel spring wire, having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

SCOPE
1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.  
1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. ^REFERENCE:
ASTM Standards:
A5 Specification for High-Carbon Steel Joint Bars; Replaced by A 3 (Withdrawn)
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel (Metric)
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1040 Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E30 Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron (Withdrawn)
E112 Test Methods for Determining Average Grain Size
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
SAE Standard:  
J 1086 Numbering Metals and Alloy
AIAG Standard:  
AIAGB-5 02.00 Primary Metals Identification Tag Application Standard

ABSTRACT
This specification covers the highest quality of round modified chromium vanadium alloy steel valve spring wires, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall either be in the annealed and cold-drawn or oil-tempered condition. The steel shall be subjected to continuous casting and be free from detrimental pipe and undue segregation. Heat and product analysis shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium. Mechanical properties shall be determined by the following: annealing and cold-drawing, oil tempering, wrap testing, and special surface inspection. In the oil-tempered condition, steel shall conform to the tensile requirements for different wire diameters. Metallurgical characterization shall include surface condition, decarburization, and inclusion content. The wire or wire rod shall conform to the maximum inclusion content requirements for the surface and core zones.
SCOPE
1.1 This specification covers the highest quality of round modified chromium vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by purchaser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other.

ABSTRACT
This specification covers the highest quality of round chromium-vanadium alloy steel wires for manufacture of valve springs and other springs with high-fatigue properties under moderately elevated temperatures. The wires shall be annealed, cold-drawn, or oil-tempered. The material shall conform to specified carbon, manganese, phosphorus, sulfur, silicon, chromium, and vanadium contents. Guidelines for mechanical testing are given. Values for tensile requirements are provided. Material decarburization shall be examined. Attention is also given to workmanship, finish, and appearance of the product, and as well as its inspection, rejection, rehearing, and certification. Packaging, marking, and loading for shipment is also described.
SCOPE
1.1 This specification covers the highest quality of round chromium-vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve springs and other springs requiring high-fatigue properties when used at moderately elevated temperatures. This wire shall be either in the annealed and cold-drawn or oil-tempered condition as specified by the purchaser.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other.