ASTM C43-08

Standard Terminology of Structural Clay Products (Withdrawn 2009)

SCOPE
1.1 This terminology contains terms and definitions of terms associated with the standards specific to masonry units and roofing tile manufactured by firing clay and shale raw materials.
1.2 The definitions and definitions of terms in this terminology pertain to Specifications C 32, C 34, C 56, C 62, C 126, C 212, C 216, C 279, C 410, C 652, C 902, C 1088, C 1167, C 1261, C 1272, C 1405, and Test Methods C 67.
1.3 Generic terminology for masonry is found in Terminology C 1232. Terminology C 1232 also applies to masonry units manufactured by firing clay and shale raw materials.
WITHDRAWN RATIONALE
This terminology contains terms and definitions of terms associated with the standards specific to masonry units and roofing tile manufactured by firing clay and shale raw materials.
Formerly under the jurisdiction of Committee C15 on Manufactured Masonry Units, this terminology was withdrawn in February 2009 and its terms were moved to Terminology C 1232 on Masonry.

General Information

• Status: Withdrawn
• Publication Date: 31-May-2008
• Withdrawal Date: 31-Jan-2009
• ICS: 81.080 - Refractories
• Technical Committee: C15 - Manufactured Masonry Units
• Drafting Committee: C15.08 - Terminology

Relations

• Replaces: ASTM C43-07 - Standard Terminology of Structural Clay Products
• Effective Date: 01-Jun-2008
• Referred By: ASTM C1400-11(2017) - Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls
• Effective Date: 01-Jun-2008
• Referred By: ASTM E2266-22 - Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
• Effective Date: 01-Jun-2008
• Referred By: ASTM C479-04(2022) - Standard Specification for Vitrified Clay Liner Plates
• Effective Date: 01-Jun-2008
• Referred By: ASTM E1602-03(2017) - Standard Guide for Construction of Solid Fuel Burning Masonry Heaters
• Effective Date: 01-Jun-2008
• Referred By: ASTM C1568-08(2020) - Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method)
• Effective Date: 01-Jun-2008
• Referred By: ASTM D5703-95(2022)e1 - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
• Effective Date: 01-Jun-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C43–08
Standard Terminology of
1
Structural Clay Products
ThisstandardisissuedunderthefixeddesignationC 43;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* C 1088 Specification for Thin Veneer Brick Units Made
From Clay or Shale
1.1 Thisterminologycontainstermsanddefinitionsofterms
C 1167 Specification for Clay Roof Tiles
associated with the standards specific to masonry units and
C 1232 Terminology of Masonry
roofing tile manufactured by firing clay and shale raw materi-
C 1261 Specification for Firebox Brick for Residential Fire-
als.
places
1.2 The definitions and definitions of terms in this terminol-
C 1272 Specification for Heavy Vehicular Paving Brick
ogy pertain to Specifications C 32, C 34, C 56, C 62, C 126,
C 1405 Specification for Glazed Brick (Single Fired, Brick
C 212, C 216, C 279, C 410, C 652, C 902, C 1088, C 1167,
Units)
C 1261, C 1272, C 1405, and Test MethodsC67.
1.3 Generic terminology for masonry is found in Terminol-
3. Terminology
ogyC 1232.TerminologyC 1232alsoappliestomasonryunits
3.1 Terms and Definitions:
manufactured by firing clay and shale raw materials.
RAW MATERIALS
2. Referenced Documents
2
2.1 ASTM Standards: clay, n—an earthy or stony mineral aggregate consisting
essentially of hydrous silicates of alumina, plastic when
C32 Specification for Sewer and Manhole Brick (Made
From Clay or Shale) sufficiently pulverized and wetted, rigid when dry, and
vitreous when fired to a sufficiently high temperature.
C34 Specification for Structural Clay Load-Bearing Wall
Tile fire clay, n—a sedimentary clay of low flux content.
reactive particulates, n—a particle or particles present in a
C56 Specification for Structural Clay Nonloadbearing Tile
C62 Specification for Building Brick (Solid Masonry Units clay body, which when near the surface may flake off or
Made From Clay or Shale) cause an eruption (pop-outs) of the surface when exposed to
the weather.
C67 Test Methods for Sampling and Testing Brick and
Structural Clay Tile shale, n—a thinly stratified, consolidated, sedimentary clay
with well-marked cleavage parallel to the bedding.
C 126 Specification for Ceramic Glazed Structural Clay
Facing Tile, Facing Brick, and Solid Masonry Units surface clay, n—an unconsolidated, unstratified clay, occur-
ring on the surface.
C 212 Specification for Structural Clay Facing Tile
C 216 Specification for Facing Brick (Solid Masonry Units
MANUFACTURE
Made from Clay or Shale)
C 279 Specification for Chemical-Resistant Masonry Units
body color—the range of color obtained when materials used
C 410 Specification for Industrial Floor Brick
toformthebrickreacttotheeffectsoffiringtemperatureand
C 652 Specification for Hollow Brick (Hollow Masonry
atmosphere.
Units Made From Clay or Shale)
DISCUSSION—Theremaybeadditivesinthebodytoproduceadesired
C 902 Specification for Pedestrian and Light Traffic Paving
color. When no materials are added to the surface of the brick and the
Brick
unit is not flashed when fired, the body color is also the through-body
color, a surface feature.
1
This terminology is under the jurisdiction of ASTM Committee C15 on
cells/core holes, n—continuous openings or perforations
Manufactured Masonry Units and is the direct responsibility of Subcommittee
within extruded clay products.
C15.08 on Terminology.
CurrenteditionapprovedJune1,2008.PublishedJuly2008.Originallyapproved
DISCUSSION—The extent of permissible openings is specified for each
in 1965. Last previous edition approved in 2007 as C 43 – 07.
product as the percentage of gross area in the normal bedding surface
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
plane that must be net (solid) area. Core hole is generally used for brick
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
while cell is used for structural tile. Cells are distinguished from core
Standards volume information, refer to the standard’s Document Summary page on
holesbybeinglargerinsize.Asanillustration,cellsmustbelargerthan
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C43–08
2 2 2 2
1
1 in. (645 mm ) under Specification C34, and 1 ⁄2 in. (968 mm )
struck surface, n—the surface of a molded brick that is not in
under Specification C 652.
contact with the mold and from which the excess clay/shale
mixture is removed.
coring, v—the process of perforating structural clay products,
webs, n—the partitions dividing tile or
...