iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D8040-18

(Test Method)

Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

SIGNIFICANCE AND USE
4.1 This test method will generally distinguish between HTF’s that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion inhibition. The actual service value of an HTF formulation can be determined by more comprehensive evaluation and field tests, agreed between customer and supplier.
SCOPE
1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air conditioning (HVAC) systems.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
30-Nov-2018
ICS
81.040.20 - Glass in building
Technical Committee
D15 - Engine Coolants and Related Fluids
Drafting Committee
D15.30 - Industrial Heat Transfer Fluids
Current Stage
Ref Project

Buy Standard

ASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in GlasswareASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware
PreviousNext
Standard
ASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in GlasswareREDLINE ASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware
PreviousNext
Standard
REDLINE ASTM D8040-18 - Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D8040 − 18
Standard Test Method for
1
Corrosion Test for Heat Transfer Fluids in Glassware
This standard is issued under the fixed designation D8040; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1384 Test Method for Corrosion Test for Engine Coolants
in Glassware
1.1 This test method covers a simple beaker-type procedure
E1 Specification for ASTM Liquid-in-Glass Thermometers
for evaluating the effects of heat transfer fluids (HTF) on metal
E177 Practice for Use of the Terms Precision and Bias in
specimens under controlled laboratory conditions. Fluids tested
ASTM Test Methods
under this method are specifically designed for heating and air
E178 Practice for Dealing With Outlying Observations
conditioning (HVAC) systems.
E230 Specification for Temperature-Electromotive Force
1.2 The values stated in SI units are to be regarded as the
(emf) Tables for Standardized Thermocouples
standard. The values given in parentheses are for information
E691 Practice for Conducting an Interlaboratory Study to
only.
Determine the Precision of a Test Method
3
1.3 This standard does not purport to address all of the 2.2 ASTM Adjunct:
safety concerns, if any, associated with its use. It is the
All-glass apparatus for corrosion test (2 drawings)
responsibility of the user of this standard to establish appro-
3. Summary of Test Method
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use. 3.1 In this test method, specimens of metals typical of those
Specific hazards statements are given in 10.1.7.2, 10.1.7.3, present in HVAC systems are totally immersed in aerated HTF
10.1.7.4, and A1.1.6. solutions for 336 h at 88 °C (190 °F). The corrosion-inhibitive
1.4 This international standard was developed in accor- properties of the test solution are evaluated on the basis of the
dance with internationally recognized principles on standard- weight changes incurred by the specimens. Each test is run in
ization established in the Decision on Principles for the triplicate, and the average weight change is determined for
Development of International Standards, Guides and Recom- each metal. A single test may occasionally be completely out of
mendations issued by the World Trade Organization Technical line (see 11.2).
Barriers to Trade (TBT) Committee.
4. Significance and Use
2. Referenced Documents
4.1 This test method will generally distinguish between
2
HTF’s that are definitely deleterious from the corrosion stand-
2.1 ASTM Standards:
point and those that are suitable for further evaluation.
B32 Specification for Solder Metal
However, the results of this test method cannot stand alone as
B36/B36M Specification for Brass Plate, Sheet, Strip, And
evidence of satisfactory corrosion inhibition. The actual ser-
Rolled Bar
vice value of an HTF formulation can be determined by more
comprehensive evaluation and field tests, agreed between
1
This test method is under the jurisdiction of ASTM Committee D15 on Engine
customer and supplier.
Coolants and Related Fluids and is the direct responsibility of Subcommittee
D15.30 on Industrial Heat Transfer Fluids.
5. Apparatus
Current edition approved Dec. 1, 2018. Published December 2018. Originally
5.1 Container, a 1000 mL, tall-form, spoutless beaker, made
approved in 2017. Last previous edition approved in 2017 as D8040–17. DOI:
10.1520/D8040–18.
of heat-resistant glass, for containing the HTF solution and test
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Details available from ASTM International Headquarters. Order Adjunct No.
the ASTM website. ADJD1384. Original adjunct produced in 1980.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D8040 − 18
FIG. 1 Metal Specimens and Equipment for 336 h Corrosion Test
specimens. The beaker shall be tightly closed with a No. 15 5.5 Heater, a constant-temperature bath containing a high-
rubber stopper, having drill holes to accommodate a water boiling liquid (see Note 1) that is capable of giving continuous
condenser, an aerator tube, and a thermometer as shown in Fig. service with the specified temperature control. The size of the
4
1. Optionally, an all-glass apparatus may be used. bath will be determined by the number of corrosion tests that
are to be
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D8040 − 17 D8040 − 18
Standard Test Method for
1
Corrosion Test for Heat Transfer Fluids in Glassware
This standard is issued under the fixed designation D8040; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal
specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air
conditioning (HVAC) systems.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
B32 Specification for Solder Metal
B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar
D1384 Test Method for Corrosion Test for Engine Coolants in Glassware
E1 Specification for ASTM Liquid-in-Glass Thermometers
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E178 Practice for Dealing With Outlying Observations
E230 Specification for Temperature-Electromotive Force (emf) Tables for Standardized Thermocouples
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3
2.2 ASTM Adjunct:
All-glass apparatus for corrosion test (2 drawings)
3. Summary of Test Method
3.1 In this test method, specimens of metals typical of those present in HVAC systems are totally immersed in aerated HTF
solutions for 336 h at 88 °C (190 °F). The corrosion-inhibitive properties of the test solution are evaluated on the basis of the
weight changes incurred by the specimens. Each test is run in triplicate, and the average weight change is determined for each
metal. A single test may occasionally be completely out of line (see 11.2).
4. Significance and Use
4.1 This test method will generally distinguish between HTF’s that are definitely deleterious from the corrosion standpoint and
those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory
corrosion inhibition. The actual service value of an HTF formulation can be determined by more comprehensive evaluation and
field tests, agreed between customer and supplier.
1
This test method is under the jurisdiction of ASTM Committee D15 on Engine Coolants and Related Fluids and is the direct responsibility of Subcommittee D15.30 on
Industrial Heat Transfer Fluids.
Current edition approved May 1, 2017Dec. 1, 2018. Published June 2017December 2018. Originally approved in 2017. Last previous edition approved in 2017 as
D8040–17. DOI: 10.1520/D8040-17.10.1520/D8040–18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
3
Details available from ASTM International Headquarters. Order Adjunct No. ADJD1384. Original adjunct produced in 1980.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D8040 − 18
5. Apparatus
5.1 Container, a 1000-mL, 1000 mL, tall-form, spoutless beaker, made of heat-resistant glass, for containing the HTF solution
and test specimens. The beaker shall be tightly closed with a No. 15 rubber stopper, having drill holes to accommodate a water
4
condenser, an aerator tube, and a thermometer as shown in Fig. 1. Optionally, an all-glass apparatus m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8040-18(2023)(Test Method)
Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

SIGNIFICANCE AND USE
4.1 This test method will generally distinguish between HTFs that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion inhibition. The actual service value of an HTF formulation can be determined by more comprehensive evaluation and field tests, agreed between customer and supplier.
SCOPE
1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air conditioning (HVAC) systems.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1279-23(Test Method)
Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass

SIGNIFICANCE AND USE
5.1 The strength and performance of heat-strengthened and fully-tempered glass is greatly affected by the surface and edge stress induced during the heat-treating process.  
5.2 The edge and surface stress levels are specified in Specification C1048, in the Engineering Standards Manual3 of GANA Tempering Division and in foreign specifications.  
5.3 This test method offers a direct and convenient way to non-destructively determine the residual state of stress on the surface and at the edge of annealed and heat-treated glass.
SCOPE
1.1 This test method covers the determination of edge stresses and surface stresses in annealed, heat-strengthened, and fully tempered flat glass products.  
1.2 This test method is non-destructive.  
1.3 This test method uses transmitted light and is, therefore, applicable to light-transmitting glasses.  
1.4 The test method is not applicable to chemically-tempered glass.  
1.5 Using the procedure described, surface stresses can be measured only on the “tin” side of float glass.  
1.6 Surface-stress measuring instruments are designed for a specific range of surface index of refraction.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D8040-18(2023)(Test Method)
Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

SIGNIFICANCE AND USE
4.1 This test method will generally distinguish between HTFs that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion inhibition. The actual service value of an HTF formulation can be determined by more comprehensive evaluation and field tests, agreed between customer and supplier.
SCOPE
1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air conditioning (HVAC) systems.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E424-71(2023)(Test Method)
Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials

SIGNIFICANCE AND USE
5.1 Solar-energy transmittance and reflectance are important factors in the heat admission through fenestration, most commonly through glass or plastics. (See Appendix X3.) These methods provide a means of measuring these factors under fixed conditions of incidence and viewing. While the data may be of assistance to designers in the selection and specification of glazing materials, the solar-energy transmittance and reflectance are not sufficient to define the rate of heat transfer without information on other important factors. The methods have been found practical for both transparent and translucent materials as well as for those with transmittances reduced by highly reflective coatings. Method B is particularly suitable for the measurement of transmittance of inhomogeneous, patterned, or corrugated materials since the transmittance is averaged over a large area.
SCOPE
1.1 These test methods cover the measurement of solar energy transmittance and reflectance (terrestrial) of materials in sheet form. Method A, using a spectrophotometer, is applicable for both transmittance and reflectance and is the referee method. Method B is applicable only for measurement of transmittance using a pyranometer in an enclosure and the sun as the energy source. Specimens for Method A are limited in size by the geometry of the spectrophotometer while Method B requires a specimen 0.61 m2 (2 ft2). For the materials studied by the drafting task group, both test methods give essentially equivalent results.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C1249-18(2023)(Guide)
Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications

SIGNIFICANCE AND USE
4.1 It should be realized that the design of an IG unit edge seal for use in SSG systems is a collaborative effort of at least the IG unit fabricator, sealant manufacturer, and design professional, among others.  
4.2 This guide provides information on silicone sealants that are used for the secondary seal of IG units that are glazed into SSG systems.  
4.3 Information is also provided on the other major components of the IG unit edge seal, compatibility of components, durability, and quality assurance (QA).
SCOPE
1.1 This guide covers design and fabrication considerations for the edge seal of conventionally sealed insulating glass units, herein referred to as IG units. The IG units described are used in structural silicone sealant glazing systems, herein referred to as SSG systems. SSG systems typically are either two or four sided, glazed with a structural sealant. Other conditions such as one, three, five, six sided may be used.  
1.2 This guides does not cover the IG units of other than conventional edge seal design (Fig. 1); however, the information contained herein may be of benefit to the designers of such IG units.
FIG. 1 Sealed IG Edge Seal: Basic Components  
1.3 In an SSG system, IG units are retained to a metal framing system by a structural seal (Fig. 2). The size and shape of that seal, as well as numerous other SSG system design considerations, are not addressed in this guide.
FIG. 2 Typical A-Side SSG System Mullion: Horizontal Section (Vertical Joint)  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 The committee with jurisdiction for this standard is not aware of any comparable standard guides published by other organizations.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    13 pages
    English language
    sale 15% off
ASTM
ASTM E2461-22(Practice)
Standard Practice for Determining the Thickness of Glass in Airport Traffic Control Tower Cabs

SIGNIFICANCE AND USE
5.1 This standard procedure facilitates determination of the thickness of a glass construction required to resist a specified design load with a selected probability of breakage.  
5.2 For optical purposes, ATCT cab glass typically utilize only annealed glass products. For this reason, some specifying authorities mandate its use and prohibit heat-strengthened and tempered glass in control cabs. This standard procedure therefore addresses the following glass constructions: annealed monolithic, annealed laminated, and insulating glass fabricated with annealed monolithic or annealed laminated glass, or both. In cases where the specifying authority approves the use of heat-strengthened or fully tempered glass in the control cab or in areas where optical characteristics do not apply but are deemed critical to the facility operation, the NFL values obtained from standard may be adjusted using appropriate Glass Type Factors (GTF) and procedures for their use as specified in Practice E1300.  
5.3 Use of these procedures assume:  
5.3.1 The glass is free of edge damage and is properly glazed,  
5.3.2 The glass has not been subjected to abuse,  
5.3.3 The surface condition of the glass is typical of glass that has been in service for several years and is significantly weaker than freshly manufactured glass due to minor abrasions on exposed surfaces,  
5.3.4 The glass edge support system is sufficiently stiff to limit the lateral deflections of the supported glass edges to less than 1/175 of their lengths. The specified design load shall be used for this calculation, and  
5.3.5 The center of glass deflection shall not result in loss of edge support. Typically maintaining center of glass deflection at or below the magnitude of three times the nominal glass thickness assures that no loss of edge support will occur.  
5.4 Many other factors affect the selection of glass type and thickness. These factors include but are not limited to: thermal stresses, the effects of win...
SCOPE
1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design wind loading.  
1.2 The procedures apply to common outward sloping cab glass designs for which the specified loads do not exceed 15 kPa (313 psf).  
1.3 The procedures assume control tower cab glass has an aspect ratio no greater than 3.  
1.4 The procedures assume control tower cab glass has an area no less than 1.86 m2 (20 ft2).  
1.5 The use of the procedures assumes the following:  
1.5.1 Monolithic and laminated glass installed in ATCTs shall have continuous lateral support along two parallel edges, along any three edges, or along all four edges;  
1.5.2 Insulating glass shall have continuous lateral support along all four edges; and  
1.5.3 Supported glass edges are simply supported and free to slip in plane.  
1.6 The procedures do not apply to any form of wired, patterned, etched, sandblasted, or glass types with surface treatments that reduce the glass strength.  
1.7 The procedures do not apply to drilled, notched, or grooved glass.  
1.8 The procedures address the determination of thickness and construction type to resist a specified design wind load at a selected probability of breakage. The final glass thickness and construction determined also depends upon a variety of other factors (see 5.4).  
1.9 These procedures do not address blast loading on glass.  
1.10 These procedures do not apply to triple-glazed insulating glass units.  
1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.12 This standard does not purport to address all of the safety concerns, if any, assoc...

  • Standard
    98 pages
    English language
    sale 15% off
  • Standard
    98 pages
    English language
    sale 15% off
ASTM
ASTM C1265-22(Test Method)
Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications

SIGNIFICANCE AND USE
5.1 Frequently IG units are adhered with a structural sealant to a metal framing system. In such applications, only the inward lite of glass is usually adhered to the frame. As a result, a significant portion of any outward-acting or negative wind load must be carried in tension by the joint seal between the two lites of the IG unit. This test will not provide information on the integrity of the IG unit primary seal; however, it may provide data on load sharing between the primary IG vapor seal and the secondary structural sealant.  
5.2 Although this test method prescribes one environmental condition, other environmental conditions and exposure cycles can be employed for specific project evaluation. Such deviations should be described when reporting the data.
SCOPE
1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.”  
1.2 The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test method must recognize that the IG edge seal assembly influences the secondary sealant properties.  
1.3 The values determined by this test method will be characteristic of the particular edge seal assembly that is tested.  
Note 1: Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized as having the necessary durability for use in structural sealant glazing applications.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F1233-21(Test Method)
Standard Test Method for Security Glazing Materials And Systems

SIGNIFICANCE AND USE
6.1 This test method is based on field experience rather than laboratory analysis. It provides a basis for the comparative evaluation of ballistic/forced entry/containment resistance of security glazings and systems and should not be used to establish or confirm the absolute prevention of forcible entries or forced exits. This test method defines three factors which determine the success or failure of any attempt to forcefully enter (or exit) the glazing or system. They are: (1) the tools employed, (2) the techniques and methods used by the attackers, and (3) the total time available to effect the entry or exit. This test method defines two of the three factors (tools and techniques) and allows the third (duration) to vary in order to establish levels of forced entry or exit resistance.
SCOPE
1.1 This test method sets forth procedures whose purpose is limited to the evaluation of the resistance of security glazing materials and systems against the following threats:  
1.1.1 Ballistic Impact,  
1.1.2 Blunt Tool Impacts,  
1.1.3 Sharp Tool Impacts,  
1.1.4 Thermal Stress,  and  
1.1.5 Chemical Deterioration.
Note 1: Specifically exempted from this test method are the use of power (motor or engine-driven) tools or devices, explosives, military ordinance (excepting small arms) and tools, processes or devices requiring more than two persons to transport and operate.  
1.2 The values stated in inch-pounds are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see Warning in 10.1.1.6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM E2141-21(Test Method)
Standard Test Method for Accelerated Aging of Electrochromic Devices in Sealed Insulating Glass Units

SIGNIFICANCE AND USE
4.1 EC glazings perform a number of important functions in a building envelope including: minimizing the solar energy heat gain; providing for passive solar energy gain; controlling a variable visual connection with the outside world; enhancing human comfort (heat gain), illumination, and glare control; and providing for architectural expression. It is therefore important to understand the relative serviceability of these glazings.  
4.2 This test method is intended to provide a means for evaluating the relative serviceability of EC Glazings as described in Section 1.  
4.3 The procedures in this test method include (a) rapid but realistic current-voltage cycling tests emphasizing the electrical properties, and (b) environmental test parameters that are typically used in weatherability tests by standards organizations and are realistic for the intended use of large-area EC IGUs.
SCOPE
1.1 This test method covers the accelerated aging of electrochromic devices (ECD) integrated in insulating glass units.  
1.2 The test method is applicable for any electrochromic device incorporated into sealed insulating glass units (IGUs) fabricated for vision glass (superstrate and substrate) areas for use in buildings, such as sliding doors, windows, skylights, and exterior wall systems. The layers used for constructing the EC device and electrochromically changing the optical properties may be inorganic or organic materials.  
1.3 The electrochromic (EC) glazings used in this test method are exposed to environmental conditions, including solar radiation. They are employed to control the amount of transmitted radiation by absorption and reflection and, thus, limit the solar heat gain and amount of solar radiation that is transmitted into the building.  
1.4 The test method is not applicable to other chromogenic devices, such as, photochromic and thermochromic devices which do not respond to electrical stimulus.  
1.5 The test method is not applicable to electrochromic (EC) glazings that are constructed from superstrate or substrate materials other than glass.  
1.6 The test method referenced herein is a laboratory test conducted under specified conditions. The test is intended to simulate and, in some cases, to also accelerate actual in-service use of the electrochromic glazing. Results from these tests cannot be used to predict the performance with time of in-service units unless actual corresponding in-service tests have been conducted and appropriate analyses have been conducted to show how performance can be predicted from the accelerated aging tests.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F3057-21(Test Method)
Standard Test Method for Electromagnetic Shielding Effectiveness of Glazings

SIGNIFICANCE AND USE
5.1 This test method provides measurement procedures for determining the electromagnetic shielding effectiveness of glazings and glazing configurations as a material. This test method specifies a method for comparing the glazings and glazing configurations as an infill component to allow comparison of between different infills. In addition, this test method is written to minimize variations in measured shielding effectiveness at a given frequency and test point regardless of test personnel, equipment, and test site. Therefore, the shielding effectiveness of a glazing or glazing configuration from any supplier can be determined. This test method specifies a minimum set of measurements over a frequency range to determine shielding effectiveness.  
5.2 Source Fields—Performance of a shielded enclosure and glazing or glazing configurations are to be assessed for three source fields: magnetic, electric, and plane wave.
SCOPE
1.1 This test method covers the determination of the electromagnetic shielding effectiveness of glazings or glazing configurations.  
1.1.1 The intended application of this test method is for glazings or glazing configurations to be evaluated for their transmittance or shielding capability to electromagnetic frequencies.  
1.1.2 This is a component test. It is not applicable to full systems such as walls, floors, ceilings, shielded racks, or window systems.  
1.1.3 The intention of this test method is to standardize a measurement procedure for glazings or glazing configurations, with and without coatings, films, interlayers, or other enhancements, as single or insulating units at a standard size and when mounted in a standardized frame.  
1.1.4 This test method is to provide a means of generating data for the glazing or glazing configuration infills that can be used by the consumer, designer, and system manufacturer to understand the capability and contribution of glazings or glazing configurations to a system used for Electromagnetic Interference (EMI) security.  
1.2 This test method is for use in the assessment of EMI transmittance for frequency ranges 100 kHz to 20 GHz. Specific test frequencies within these ranges are required.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 8 on Hazards.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off