ASTM B338-13

Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers

ABSTRACT
This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements prescribed. Welded tube shall be made from flat-rolled product by an automatic arc-welding process. The welded tube shall be sufficiently cold worked to final size in order to transform the cast weld microstructure into a typical equiaxed microstructure in the weld upon subsequent heat treatment. The titanium shall conform to the chemical requirements prescribed. The room temperature tensile properties of the tube in the condition normally supplied shall conform to the requirements prescribed. Tubing shall withstand, without cracking, flattening under a load applied gradually at room temperature until the distance between the load platens is not more than the required height. Welded tube shall be subjected to a reverse flattening test in accordance with supplement II of test methods and definitions A 370. Welded tubing shall be tested using both a non-destructive electromagnetic test and an ultrasonic test method. Seamless and welded/cold worked tubing shall be tested using an ultrasonic test method. Welded tubing shall be tested with a hydrostatic or pneumatic test method. Seamless tubing shall be tested with an electromagnetic or hydrostatic or pneumatic test method.
SCOPE
1.1 This specification2 covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers, as follows:  
1.1.1 Grade 1—Unalloyed titanium,  
1.1.2 Grade 2—Unalloyed titanium,
1.1.2.1 Grade 2H—Unalloyed titanium (Grade 2 with 58 ksi minimum UTS),  
1.1.3 Grade 3—Unalloyed titanium,  
1.1.4 Grade 7—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.4.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi minimum UTS),  
1.1.5 Grade 9—Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.6 Grade 11—Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.7 Grade 12—Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.8 Grade 13—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.9 Grade 14—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.10 Grade 15—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.11 Grade 16—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.11.1 Grade 16H—Unalloyed titanium plus 0.04 to 0.08 % palladium (Grade 16 with 58 ksi minimum UTS),  
1.1.12 Grade 17—Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.13 Grade 18—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.14 Grade 26—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.14.1 Grade 26H—Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),  
1.1.15 Grade 27—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.16 Grade 28—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 to 0.14 % ruthenium,  
1.1.17 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.18 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.19 Grade 33—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.20 Grade 34—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.21 Grade 35—Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),  
1.1.22 Grade 36—Titanium alloy (45 % niobium),  
1.1.23 Grade 37—Titanium alloy (1.5 % aluminum),  
1.1.24 Grade 38—Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron), and  
1.1.25 Grade 39—Titanium alloy (0.25 % iron, 0.4 % silicon).Note 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed minimum UTS, and may always be certified as meet...

General Information

• Status: Historical
• Publication Date: 31-May-2013
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B10 - Reactive and Refractory Metals and Alloys
• Drafting Committee: B10.01 - Titanium

Relations

• Replaces: ASTM B338-10e1 - Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers
• Effective Date: 01-Jun-2013
• Replaced By: ASTM B338-13a - Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers
• Effective Date: 01-Jul-2013
• Referred By: ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
• Effective Date: 01-Jun-2013
• Referred By: ASTM B891/B891M-19 - Standard Specification for Seamless and Welded Titanium and Titanium Alloy Condenser and Heat Exchanger Tubes with Enhanced Surface for Improved Heat Transfer
• Effective Date: 01-Jun-2013
• Referred By: ASTM F1511-18(2023) - Standard Specification for Mechanical Seals for Shipboard Pump Applications
• Effective Date: 01-Jun-2013
• Referred By: ASTM F2015-00(2019) - Standard Specification for Lap Joint Flange Pipe End Applications
• Effective Date: 01-Jun-2013
• Referred By: ASTM B363-19 - Standard Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings
• Effective Date: 01-Jun-2013
• Referred By: ASTM F2014-00(2019) - Standard Specification for Non-Reinforced Extruded Tee Connections for Piping Applications
• Effective Date: 01-Jun-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B338 −13
StandardSpecification for
Seamless and Welded Titanium and Titanium Alloy Tubes
1
for Condensers and Heat Exchangers
This standard is issued under the fixed designation B338; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 1.1.13 Grade 18—Titanium alloy (3 % aluminum, 2.5 %
2 vanadium) plus 0.04 to 0.08 % palladium,
1.1 This specification covers the requirements for 28
1.1.14 Grade 26—Unalloyed titanium plus 0.08 to 0.14 %
grades of titanium and titanium alloy tubing intended for
ruthenium,
surface condensers, evaporators, and heat exchangers, as fol-
lows:
1.1.14.1 Grade 26H—Unalloyed titanium plus 0.08 to
1.1.1 Grade 1—Unalloyed titanium,
0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
1.1.2 Grade 2—Unalloyed titanium,
1.1.15 Grade 27—Unalloyed titanium plus 0.08 to 0.14 %
1.1.2.1 Grade 2H—Unalloyedtitanium(Grade2with58ksi
ruthenium,
minimum UTS),
1.1.16 Grade 28—Titanium alloy (3 % aluminum, 2.5 %
1.1.3 Grade 3—Unalloyed titanium,
vanadium) plus 0.08 to 0.14 % ruthenium,
1.1.4 Grade 7—Unalloyed titanium plus 0.12 to 0.25 %
1.1.17 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 %
palladium,
palladium),
1.1.4.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 %
palladium (Grade 7 with 58 ksi minimum UTS),
1.1.18 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 %
1.1.5 Grade 9—Titanium alloy (3 % aluminum, 2.5 %
palladium),
vanadium),
1.1.19 Grade 33—Titanium alloy (0.4 % nickel, 0.015 %
1.1.6 Grade 11—Unalloyed titanium plus 0.12 to 0.25 %
palladium, 0.025 % ruthenium, 0.15 % chromium),
palladium,
1.1.20 Grade 34—Titanium alloy (0.4 % nickel, 0.015 %
1.1.7 Grade 12—Titaniumalloy(0.3 %molybdenum,0.8 %
palladium, 0.025 % ruthenium, 0.15 % chromium),
nickel),
1.1.21 Grade 35—Titanium alloy (4.5 % aluminum, 2 %
1.1.8 Grade 13—Titanium alloy (0.5 % nickel, 0.05 %
molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
ruthenium),
1.1.22 Grade 36—Titanium alloy (45 % niobium),
1.1.9 Grade 14—Titanium alloy (0.5 % nickel, 0.05 %
ruthenium),
1.1.23 Grade 37—Titanium alloy (1.5 % aluminum),
1.1.10 Grade 15—Titanium alloy (0.5 % nickel, 0.05 %
1.1.24 Grade 38—Titanium alloy (4 % aluminum, 2.5 %
ruthenium),
vanadium, 1.5 % iron), and
1.1.11 Grade 16—Unalloyed titanium plus 0.04 to 0.08 %
1.1.25 Grade 39—Titanium alloy (0.25 % iron, 0.4 %
palladium,
silicon).
1.1.11.1 Grade 16H—Unalloyed titanium plus 0.04 to
0.08 % palladium (Grade 16 with 58 ksi minimum UTS),
NOTE 1—H grade material is identical to the corresponding numeric
1.1.12 Grade 17—Unalloyed titanium plus 0.04 to 0.08 %
grade (that is, Grade 2H = Grade 2) except for the higher guaranteed
palladium, minimum UTS, and may always be certified as meeting the requirements
of its corresponding numeric grade. Grades 2H, 7H, 16H, and 26H are
intended primarily for pressure vessel use.
The H grades were added in response to a user association request
1
This specification is under the jurisdiction of ASTM Committee B10 on
based on its study of over 5200 commercial Grade 2, 7, 16, and 26 test
Reactive and Refractory Metals and Alloys and is the direct responsibility of
reports, where over 99 % met the 58 ksi minimum UTS.
Subcommittee B10.01 on Titanium.
Current edition approved June 1, 2013. Published June 2013. Originally
1.2 The values stated in inch-pound units are to be regarded
ε1
approved in 1958. Last previous edition approved in 2010 as B338 – 10 . DOI:
as standard. The values given in parentheses are mathematical
10.1520/B0338-13.
2 conversions to SI units that are provided for information only
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
cation SB-338 in Section II of that Code. and are not considered standard.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B338−13
2. Referenced Documents 4.1.7 Product analysis, if desired (Section 7 and Table 2),
3 4.1.8 Special mechanical properties, if desired (Section 8
2.1 ASTM Standards:
and Table 3),
A370 Test Methods and Definitions for Mechanical Testing
4.1.9 Nondestructive tests (Section 11),
of Steel Products
4.1.10 Packaging (Section 23),
E8 Test Methods for Tension Testing of Metallic Materials
4.1.11 Inspection (Section 17), and
E29 Practice for Using Significant Digits in Test Data to
4.1.12 Certification (Section 21).
Determine Conformance with Specifications
E1409 Test Method for Det
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: B338 − 10 B338 − 13
Standard Specification for
Seamless and Welded Titanium and Titanium Alloy Tubes
1
for Condensers and Heat Exchangers
This standard is issued under the fixed designation B338; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
ε NOTE—References in section 11.1 were corrected editorially in April 2012.
1. Scope*
2
1.1 This specification covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface
condensers, evaporators, and heat exchangers, as follows:
1.1.1 Grade 1—Unalloyed titanium,
1.1.2 Grade 2—Unalloyed titanium,
1.1.2.1 Grade 2H—Unalloyed titanium (Grade 2 with 58 ksi minimum UTS),
1.1.3 Grade 3—Unalloyed titanium,
1.1.4 Grade 7—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.4.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi minimum UTS),
1.1.5 Grade 9—Titanium alloy (3 % aluminum, 2.5 % vanadium),
1.1.6 Grade 11—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7 Grade 12—Titanium alloy (0.3 % molybdenum, 0.8 % nickel),
1.1.8 Grade 13—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.9 Grade 14—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.10 Grade 15—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.11 Grade 16—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.11.1 Grade 16H—Unalloyed titanium plus 0.04 to 0.08 % palladium (Grade 16 with 58 ksi minimum UTS),
1.1.12 Grade 17—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.13 Grade 18—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,
1.1.14 Grade 26—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.14.1 Grade 26H—Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
1.1.15 Grade 27—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.16 Grade 28—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 to 0.14 % ruthenium,
1.1.17 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.18 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.19 Grade 33—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.20 Grade 34—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.21 Grade 35—Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
1.1.22 Grade 36—Titanium alloy (45 % niobium),
1.1.23 Grade 37—Titanium alloy (1.5 % aluminum), and
1.1.24 Grade 38—Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron).iron), and
NOTE 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed minimum
UTS, and may always be certified as meeting the requirements of its corresponding numeric grade. Grades 2H, 7H, 16H, and 26H are intended primarily
for pressure vessel use.
1
This specification is under the jurisdiction of ASTM Committee B10 on Reactive and Refractory Metals and Alloys and is the direct responsibility of Subcommittee
B10.01 on Titanium.
Current edition approved May 1, 2010June 1, 2013. Published May 2010June 2013. Originally approved in 1958. Last previous edition approved in 20092010 as
ε1
B338 – 09.B338 – 10 . DOI: 10.1520/B0338-10E01.10.1520/B0338-13.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-338 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B338 − 13
The H grades were added in response to a user association request based on its study of over 5200 commercial Grade 2, 7, 16, and 26 test reports,
where over 99 % met the 58 ksi minimum UTS.
1.1.25 Grade 39—Titanium alloy (0.25 % iron, 0.4 % silicon).
NOTE 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed minimum
UTS, and may always be certified as meeting the requirements of its corresponding numeric grade. Grades 2H, 7H, 16H, and 26H are intended primarily
for pressure vessel use.
The H grades were added in response
...